Problemi sulle tty e su LI..LO
Saluti a tutti,
ho da poco installato la debian su una macchina con un processore cyrix, il
problema piu' grosso che non riesco proprio a risolvere è che quando riavvio il
LILO si ferma su LI nonostante se faccio lilo -v tutto sembra essere normale e
a posto.
Il problema piu' curioso invece riguarda le porte tty che all'avvio ne vede un
po' troppe, vi allego il testo di dmesg...
Grazie a tutti.
Andrea.
Memory: sized by int13 088h
Console: 16 point font, 400 scans
Console: colour VGA+ 80x25, 1 virtual console (max 63)
pcibios_init : BIOS32 Service Directory structure at 0x000fb040
pcibios_init : BIOS32 Service Directory entry at 0xfb440
pcibios_init : PCI BIOS revision 2.10 entry at 0xfb470
Probing PCI hardware.
Calibrating delay loop.. ok - 132.71 BogoMIPS
Memory: 14044k/16384k available (1136k kernel code, 384k reserved, 820k data)
This processor honours the WP bit even when in supervisor mode. Good.
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: IGMP, ICMP, UDP, TCP
VFS: Diskquotas version dquot_5.6.0 initialized_
Checking 386/387 coupling... Ok, fpu using exception 16 error reporting.
Checking 'hlt' instruction... Ok.
Linux version 2.0.36 (root@gondor) (gcc version 2.7.2.3) #2 Sun Jan 17 19:38:45
EST 1999
Starting kswapd v 1.4.2.2
Real Time Clock Driver v1.09
tpqic02: Runtime config, $Revision: 0.4.1.5 $, $Date: 1994/10/29 02:46:13 $
tpqic02: DMA buffers: 20 blocks, at address 0x282800 (0x2826ec)
Ramdisk driver initialized : 16 ramdisks of 4096K size
loop: registered device at major 7
hda: FUJITSU M1623TAU, 1623MB w/128kB Cache, CHS=824/64/63
hdc: CRD-8322B, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
Floppy drive(s): fd0 is 1.44M
FDC 0 is an 8272A
md driver 0.36.3 MAX_MD_DEV=4, MAX_REAL=8
Failed initialization of WD-7000 SCSI card!
scsi : 0 hosts.
scsi : detected total.
Partition check:
hda: [PTBL] [206/255/63] hda1 hda2
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 80320k swap-space (priority -1)
ne2k-pci.c:v0.99L 2/7/98 D. Becker/P. Gortmaker
http://cesdis.gsfc.nasa.gov/linux/drivers/ne2k-pci.html
ne2k-pci.c: PCI NE2000 clone 'Winbond 89C940' at I/O 0x6100, IRQ 11.
eth0: PCI NE2000 found at 0x6100, IRQ 11, 48:54:E8:27:11:1D.
Serial driver version 4.13 with no serial options enabled
tty00 at 0x03f8 (irq = 4) is a 16550A
tty01 at 0x02f8 (irq = 3) is a 16550A
tty32 at 0x3220 (irq = 3) is a 8250
tty33 at 0x3228 (irq = 3) is a 16550
tty34 at 0x4220 (irq = 3) is a 8250
tty35 at 0x4228 (irq = 3) is a 16550
tty36 at 0x5220 (irq = 3) is a 8250
tty37 at 0x5228 (irq = 3) is a 16550
eth0: Tx timed out, cable problem? TSR=0x0, ISR=0x0, t=1000.
Reply to: