Re: Booting The Debian GNU/Hurd get locked
On Thu, 20 Jan 2005, Yuval Tanny wrote:
> No. I didn't run it at all. The guide say: "Once you are presented with
> a shell prompt, and any time that the Hurd is in single user mode, it is
> necessary to set the terminal type:". I hadn't presented with a shell
> prompt in the GNU/Hurd system, yet. Should I chroot to in and run it
> (twice?)?
You will need to boot into your Hurd system to run ./native-install. This
needs to be done twice.
>
> (I'm not using the K8 installer...)
The tarball is very similar to baseGNU on the CD set.
Phil.
>
> Thanks,
>
> Yuval
>
>
> Philip Charles wrote:
>
> >Yuval,
> > Have you run ./native-install twice?
> >
> >Phil.
> >
> >On Thu, 20 Jan 2005, Yuval Tanny wrote:
> >
> >
> >
> >>Hello,
> >>
> >>
> >>After following this:
> >>
> >>http://www.debian.org/ports/hurd/hurd-install
> >>
> >>installation guide, I get this message at boot:
> >>
> >>(this is what I see on the screen)
> >>
> >>
> >>ide0 at 0x1f0-0x1f7, 0x3f6 on irq 14
> >>
> >>ide1 at 0x170-0x177, 0x3f6 on irq 15
> >>
> >>Floppy...
> >>
> >>FDC is a post 1991 82077
> >>
> >>Failed initialization of WD-7000 SCSI card!
> >>
> >>EATAO, address 0x1f0 in use skipping probe.
> >>
> >>EATAO, address 0x170 in use skipping probe.
> >>
> >>ppa: Version 1.42
> >>
> >>ppa: Probing port 03bc
> >>
> >>ppa: Probing port 0378
> >>
> >>...(and some other lines from ppa)..
> >>
> >>scsi: 0 hosts.
> >>
> >>scsi: detected total.
> >>
> >>rtl8139.c:B1.23a ...
> >>
> >> http:///www...
> >>
> >>eth0: RealTek RTL81396 Fast Ethernet at 0xa00 IRQ 10, 0:e0:ud: 7:98:ca
> >>
> >>Now the system lock. It's not responding.
> >>
> >>
> >>I installed from debian-gnu-hurd-2004.12.30.tar.gz. I have ABIT NF7-S
> >>(nforce 2 with SCSI controller that is in no use) motherboard, WD800JB
> >>hard disc (ATA connected), the Debian GNU/Hurd is on hda1or hd0s1 (I
> >>hope :-) ), It's a 6 GB (maybe this is it?) ext2 hurd partition.
> >>
> >>
> >>What is the problem and how can I fix it?
> >>
> >>
> >>I'll be glade to give more info,
> >>
> >>Thanks,
> >>
> >>Yuval
> >>
> >>
> >>--
> >>To UNSUBSCRIBE, email to debian-hurd-REQUEST@lists.debian.org
> >>with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
> >>
> >>
> >>
> >>
> >
> >--
> > Philip Charles; 39a Paterson Street, Abbotsford, Dunedin, New Zealand
> > +64 3 488 2818 Fax +64 3 488 2875 Mobile 025 267 9420
> > philipc@copyleft.co.nz - preferred. philipc@debian.org
> > I sell GNU/Linux & GNU/Hurd CDs & DVDs. See http://www.copyleft.co.nz
> >
> >
> >
> >
>
>
--
Philip Charles; 39a Paterson Street, Abbotsford, Dunedin, New Zealand
+64 3 488 2818 Fax +64 3 488 2875 Mobile 025 267 9420
philipc@copyleft.co.nz - preferred. philipc@debian.org
I sell GNU/Linux & GNU/Hurd CDs & DVDs. See http://www.copyleft.co.nz
Reply to: