[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: install/update/upgrade dance



 Dave, Helge et al,

The 3.9 kernel installs and boots but wants to use the serial console (OK I can do that). The displayed boot sequence stops at "Stopping boot logger: bootlogd." but a power button shutdown will get a response on the serial console. Please find attached the serial console trace.

I need to go outside and clean bricks before forecast rain gets here :-(.

Cheers,

Geoff.




----- Original Message -----
From:

To:

Cc:

Sent:

Subject:






Firmware Version 2.0


Duplex Console IO Dependent Code (IODC) revision 1

------------------------------------------------------------------------------

   (c) Copyright 1995-2000, Hewlett-Packard Company, All rights reserved

------------------------------------------------------------------------------


  Processor   Speed            State           Coprocessor State  I/D Cache 

  ---------  --------   ---------------------  -----------------  -------------

      0      750 MHz    Active                 Functional         768 kB/1536 kB

  Central Bus Speed:                   120 MHz

  Available memory:             1073741824 bytes
  Good memory required:           30945280 bytes

  Primary boot path:    FWSCSI.6.0
  Alternate boot path:  SCSI.6.0
  Console path:         GRAPHICS(2)
  Keyboard path:        USB


Processor is booting from first available device.


To discontinue, press any key within 10 seconds.


Boot terminated.



----- Main Menu -------------------------------------------------------------

      Command                           Description
      -------                           -----------
      BOot [PRI|ALT|<path>]             Boot from specified path
      PAth [PRI|ALT|CON|KEY [<path>]]   Display or modify a path
      SEArch [DIsplay|[[IPL] [<path>]]] Search for boot devices

      COnfiguration [<command>]         Access Configuration menu/commands
      INformation [<command>]           Access Information menu/commands
      SERvice [<command>]               Access Service menu/commands

      DIsplay                           Redisplay the current menu
      HElp [<menu>|<command>]           Display help for menu or command
      RESET                             Restart the system
-----
Main Menu: Enter command > sea


Searching for potential boot device(s)...

This may take several minutes.


To discontinue search, press any key (termination may not be immediate).



   Path Number        Device Path              Device Type

   -----------        -----------------        -----------

   P0                 IDE                      LITE-ON DVDRW SHM-165P6S
   P1                 FWSCSI.6.0               HP 18.2GMAN3184MC       


Main Menu: Enter command > bo p1

Interact with IPL (Y, N, Q)?> y



Booting... 

Boot IO Dependent Code (IODC) revision 0




HARD Booted.

palo ipl 1.14 root@penalosa Wed Oct  8 15:04:37 UTC 2008

Skipping extended partition 6 - beyond reach of IPL



Partition Start(MB) End(MB) Id Type


1               1      31   f0 Palo


2              32     156   83 ext2


5             157   16669   83 ext2



PALO(F0) partition contains:

    0/vmlinux32 4188604 bytes @ 0x48000


Information: No console specified on kernel command line. This is normal.

PALO will choose the console currently used by firmware (serial).Current command line:

2/vmlinux root=/dev/sda5 initrd=2/initrd.img HOME=/ console=ttyS0 TERM=vt102

 0: 2/vmlinux

 1: root=/dev/sda5

 2: initrd=2/initrd.img

 3: HOME=/

 4: console=ttyS0

 5: TERM=vt102


<#>    edit the numbered field

'b'    boot with this command line

'r'    restore command line

'l'    list dir

? 0 l

Directory listing of /.


  lost+found

  initrd.img

  vmlinux

  System.map-2.6.26-2-parisc

  config-2.6.26-2-parisc

  vmlinux-2.6.26-2-parisc

  initrd.img-2.6.26-2-parisc

  vmlinux-3.9

  config.parisc-kernel-3.9


Current command line:

2/vmlinux root=/dev/sda5 initrd=2/initrd.img HOME=/ console=ttyS0 TERM=vt102

 0: 2/vmlinux

 1: root=/dev/sda5

 2: initrd=2/initrd.img

 3: HOME=/

 4: console=ttyS0

 5: TERM=vt102


<#>    edit the numbered field

'b'    boot with this command line

'r'    restore command line

'l'    list dir

? 0 2 0

2/vmlinux-3.9

Current command line:

2/vmlinux-3.9 root=/dev/sda5 initrd=2/initrd.img HOME=/ console=ttyS0 TERM=vt102

 0: 2/vmlinux-3.9

 1: root=/dev/sda5

 2: initrd=2/initrd.img

 3: HOME=/

 4: console=ttyS0

 5: TERM=vt102


<#>    edit the numbered field

'b'    boot with this command line

'r'    restore command line

'l'    list dir

? 0 2

initrd=2/initrd.img                   

Current command line:

2/vmlinux-3.9 root=/dev/sda5  HOME=/ console=ttyS0 TERM=vt102

 0: 2/vmlinux-3.9

 1: root=/dev/sda5

 2: HOME=/

 3: console=ttyS0

 4: TERM=vt102


<#>    edit the numbered field

'b'    boot with this command line

'r'    restore command line

'l'    list dir

? 0 b


Command line for kernel: 'root=/dev/sda5 HOME=/ console=ttyS0 TERM=vt102 palo_kernel=2/vmlinux-3.9'

Selected kernel: /vmlinux-3.9 from partition 2

ELF64 executable

Entry 00100000 first 00100000 n 2

Segment 0 load 00100000 size 9170944 mediaptr 0x1000

Segment 1 load 00a3fe40 size 1206912 mediaptr 0x8c0e40

Branching to kernel entry point 0x00100000.  If this is the last

message you see, you may need to switch your console.  This is

a common symptom -- search the FAQ and mailing list at parisc-linux.org


[    0.000000] Linux version 3.9.0-64bit+ (deller@ls3530) (gcc version 4.7.2 20121105 (Red Hat 4.7.2-2.aa.20121114svn) (GCC) ) #226 SMP Thu May 9 23:02:41 CEST 2013
[    0.000000] unwind_init: start = 0x40884000, end = 0x408c9a00, entries = 17824
[    0.000000] FP[0] enabled: Rev 1 Model 19
[    0.000000] The 64-bit Kernel has started...
[    0.000000] bootconsole [ttyB0] enabled
[    0.000000] Initialized PDC Console for debugging.
[    0.000000] Determining PDC firmware type: System Map.
[    0.000000] model 00005dc0 00000481 00000000 00000002 77dc0ab2 100000f0 00000008 000000b2 000000b2
[    0.000000] vers  00000203
[    0.000000] CPUID vers 19 rev 7 (0x00000267)
[    0.000000] capabilities 0x7
[    0.000000] model 9000/785/C3700
[    0.000000] Total Memory: 1024 MB
[    0.000000] LCD display at fffffff0f05d0008,fffffff0f05d0000 registered
[    0.000000] PERCPU: Embedded 10 pages/cpu @0000000041a88000 s10432 r8192 d22336 u40960
[    0.000000] SMP: bootstrap CPU ID is 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 258560
[    0.000000] Kernel command line: root=/dev/sda5 HOME=/ console=ttyS0 TERM=vt102 palo_kernel=2/vmlinux-3.9
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[    0.000000] Memory: 1019548k/1048576k available (6676k kernel code, 29028k reserved, 2227k data, 348k init)
[    0.000000] virtual kernel memory layout:
    0.000000]     vmalloc : 0x0000000000008000 - 0x000000003f000000   (1007 MB)
    0.000000]     memory  : 0x0000000040000000 - 0x0000000080000000   (1024 MB)
    0.000000]       .init : 0x0000000040b10000 - 0x0000000040b67000   ( 348 kB)
    0.000000]       .data : 0x00000000407853b8 - 0x00000000409b22f0   (2227 kB)
    0.000000]       .text : 0x0000000040100000 - 0x00000000407853b8   (6676 kB)
[    0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=8
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	CONFIG_RCU_FANOUT set to non-default value of 32
[    0.000000] NR_IRQS:128
[    0.000000] Console: colour dummy device 160x64
[    0.056000] Calibrating delay loop... 1494.01 BogoMIPS (lpj=2988032)
[    0.164000] pid_max: default: 32768 minimum: 301
[    0.224000] Mount-cache hash table entries: 256
[    0.284000] Brought up 1 CPUs
[    0.324000] devtmpfs: initialized
[    0.372000] atomic64 test passed
[    0.416000] regulator-dummy: no parameters
[    0.468000] NET: Registered protocol family 16
[    0.528000] Searching for devices...
[    0.804000] Found devices:
[    0.840000] 1. Astro BC Runway Port at 0xfffffffffed00000 [10] { 12, 0x0, 0x582, 0x0000b }
[    0.948000] 2. Elroy PCI Bridge at 0xfffffffffed30000 [10/0] { 13, 0x0, 0x782, 0x0000a }
[    1.056000] 3. Elroy PCI Bridge at 0xfffffffffed32000 [10/1] { 13, 0x0, 0x782, 0x0000a }
[    1.160000] 4. Elroy PCI Bridge at 0xfffffffffed38000 [10/4] { 13, 0x0, 0x782, 0x0000a }
[    1.268000] 5. Elroy PCI Bridge at 0xfffffffffed3c000 [10/6] { 13, 0x0, 0x782, 0x0000a }
[    1.372000] 6. Allegro W2 at 0xfffffffffffa0000 [32] { 0, 0x0, 0x5dc, 0x00004 }
[    1.472000] 7. Memory at 0xfffffffffed10200 [49] { 1, 0x0, 0x09c, 0x00009 }
[    1.560000] Enabling regular chassis codes support v0.05
[    1.764000] CPU(s): 1 x PA8700 (PCX-W2) at 750.000000 MHz
[    1.840000] Setting cache flush threshold to 180000 (1 CPUs online)
[    1.948000] SBA found Astro 2.1 at 0xfffffffffed00000
[    2.016000] Elroy version TR4.0 (0x5) found at 0xfffffffffed30000
[    2.096000] LBA 10:0: PCI host bridge to bus 0000:00
[    2.160000] pci_bus 0000:00: root bus resource [io  0x0000-0x1fff]
[    2.244000] pci_bus 0000:00: root bus resource [mem 0xfffffffff4000000-0xfffffffff47fffff] (bus address [0xf4000000-0xf47fffff])
[    2.396000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    2.488000] PCI: Enabled native mode for NS87415 (pif=0x8f)
[    2.564000] Elroy version TR4.0 (0x5) found at 0xfffffffffed32000
[    2.644000] LBA 10:1: PCI host bridge to bus 0000:01
[    2.712000] pci_bus 0000:01: root bus resource [io  0x12000-0x13fff] (bus address [0x2000-0x3fff])
[    2.828000] pci_bus 0000:01: root bus resource [mem 0xfffffffff4800000-0xfffffffff4ffffff] (bus address [0xf4800000-0xf4ffffff])
[    2.980000] pci_bus 0000:01: root bus resource [??? 0x00000001 flags 0x0]
[    3.072000] Elroy version TR4.0 (0x5) found at 0xfffffffffed38000
[    3.152000] LBA 10:4: PCI host bridge to bus 0000:02
[    3.216000] pci_bus 0000:02: root bus resource [io  0x28000-0x29fff] (bus address [0x8000-0x9fff])
[    3.336000] pci_bus 0000:02: root bus resource [mem 0xfffffffff6000000-0xfffffffff67fffff] (bus address [0xf6000000-0xf67fffff])
[    3.488000] pci_bus 0000:02: root bus resource [??? 0x00000002 flags 0x0]
[    3.576000] Elroy version TR4.0 (0x5) found at 0xfffffffffed3c000
[    3.656000] LBA 10:6: PCI host bridge to bus 0000:03
[    3.724000] pci_bus 0000:03: root bus resource [io  0x3c000-0x3dfff] (bus address [0xc000-0xdfff])
[    3.840000] pci_bus 0000:03: root bus resource [mem 0xfffffffffa000000-0xfffffffffbffffff] (bus address [0xfa000000-0xfbffffff])
[    3.992000] pci_bus 0000:03: root bus resource [mem 0xfffffffff7000000-0xfffffffff77fffff] (bus address [0xf7000000-0xf77fffff])
[    4.144000] pci_bus 0000:03: root bus resource [??? 0x00000003 flags 0x0]
[    4.236000] iosapic: hpa not registered for 0000:03:02.0
[    4.312000] powersw: Soft power switch at 0xfffffff0f0400804 enabled.
[    4.400000] bio: create slab <bio-0> at 0
[    4.456000] vgaarb: loaded
[    4.492000] SCSI subsystem initialized
[    4.540000] Switching to clocksource cr16
[    4.600000] NET: Registered protocol family 2
[    4.660000] TCP established hash table entries: 8192 (order: 5, 131072 bytes)
[    4.752000] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[    4.840000] TCP: Hash tables configured (established 8192 bind 8192)
[    4.924000] TCP: reno registered
[    4.964000] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    5.044000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    5.128000] NET: Registered protocol family 1
[    5.184000] RPC: Registered named UNIX socket transport module.
[    5.264000] RPC: Registered udp transport module.
[    5.324000] RPC: Registered tcp transport module.
[    5.388000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    5.472000] SuperIO: Found NS87560 Legacy I/O device at 0000:00:0e.1 (IRQ 68)
[    5.564000] SuperIO: Serial port 1 at 0x3f8
[    5.620000] SuperIO: Serial port 2 at 0x2f8
[    5.676000] SuperIO: Parallel port at 0x378
[    5.732000] SuperIO: Floppy controller at 0x3f0
[    5.788000] SuperIO: ACPI at 0x7e0
[    5.836000] SuperIO: USB regulator enabled
[    5.944000] Enabling PDC chassis warnings support v0.05
[    6.012000] Performance monitoring counters enabled for Allegro W2
[    6.104000] VFS: Disk quotas dquot_6.5.2
[    6.156000] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    6.244000] fuse init (API version 7.21)
[    6.296000] msgmni has been set to 1991
[    6.348000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    6.448000] io scheduler noop registered
[    6.496000] io scheduler cfq registered (default)
[    6.564000] PDC Stable Storage facility v0.30
[    6.956000] STI GSC/PCI core graphics driver Version 0.9a
[    7.028000] sti 0000:03:02.0: enabling SERR and PARITY (0002 -> 0142)
[    7.112000] STI PCI graphic ROM found at fffffffff7000000 (64 kB), fb at fffffffffa000000 (32 MB)
[    7.312000] Unable to handle STI device '0000:03:02.0'
[    7.380000] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    7.460000] serial8250: ttyS0 at I/O 0x3f8 (irq = 3) is a 16550A
[    7.540000] console [ttyS0] enabled, bootconsole disabled
[    7.540000] console [ttyS0] enabled, bootconsole disabled
[    7.676000] serial8250: ttyS1 at I/O 0x2f8 (irq = 4) is a 16550A
[    7.752000] loop: module loaded
[    7.788000] Uniform Multi-Platform E-IDE driver
[    7.844000] Loading iSCSI transport class v2.0-870.
[    7.904000] iscsi: registered transport (qla4xxx)
[    7.960000] QLogic iSCSI HBA Driver
[    8.196000] sym0: <896> rev 0x7 at pci 0000:00:0f.0 irq 69
[    8.264000] sym0: PA-RISC Firmware, ID 7, Fast-40, SE, parity checking
[    8.340000] sym0: SCSI BUS has been reset.
[    8.396000] scsi0 : sym-2.2.3
[   13.588000] sym1: <896> rev 0x7 at pci 0000:00:0f.1 irq 69
[   13.656000] sym1: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking
[   13.736000] sym1: SCSI BUS has been reset.
[   13.792000] scsi1 : sym-2.2.3
[   18.496000] scsi 1:0:6:0: Direct-Access     HP 18.2G MAN3184MC        HP07 PQ: 0 ANSI: 2
[   18.592000] scsi target1:0:6: tagged command queuing enabled, command queue depth 16.
[   18.688000] scsi target1:0:6: Beginning Domain Validation
[   18.756000] scsi target1:0:6: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31)
[   18.844000] scsi target1:0:6: Domain Validation skipping write tests
[   18.920000] scsi target1:0:6: Ending Domain Validation
[   21.372000] tun: Universal TUN/TAP device driver, 1.6
[   21.432000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   21.508000] Linux Tulip driver version 1.1.15 (Feb 27, 2007)
[   21.584000] tulip0: no phy info, aborting mtable build
[   21.644000] tulip0:  MII transceiver #1 config 1000 status 782d advertising 01e1
[   21.740000] net eth0: Digital DS21142/43 Tulip rev 65 at Port 0x1000, 00:30:6e:2b:67:6a, IRQ 66
[   21.844000] LASI 82596 driver - Revision: 1.30
[   21.900000] mousedev: PS/2 mouse device common for all mice
[   21.968000] sd 1:0:6:0: [sda] 35566480 512-byte logical blocks: (18.2 GB/16.9 GiB)
[   22.060000] rtc-generic rtc-generic: rtc core: registered rtc-generic as rtc0
[   22.144000] Netfilter messages via NETLINK v0.30.
[   22.200000] sd 1:0:6:0: [sda] Write Protect is off
[   22.260000] TCP: cubic registered
[   22.300000] NET: Registered protocol family 17
[   22.352000] NET: Registered protocol family 33
[   22.404000] Key type rxrpc registered
[   22.448000] sd 1:0:6:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   22.556000] Key type rxrpc_s registered
[   22.604000] registered taskstats version 1
[   22.656000] rtc-generic rtc-generic: setting system clock to 2013-05-12 00:57:52 UTC (1368320272)
[   22.800000]  sda: sda1 sda2 sda3 < sda5 sda6 >
[   22.868000] sd 1:0:6:0: [sda] Attached SCSI disk
[   22.960000] kjournald starting.  Commit interval 5 seconds
[   23.028000] EXT3-fs (sda5): mounted filesystem with ordered data mode
[   23.104000] VFS: Mounted root (ext3 filesystem) readonly on device 8:5.
[   23.184000] Freeing unused kernel memory: 348k freed
modprobe: FATAL: Could not load /lib/modules/3.9.0-64bit+/modules.dep: No such file or directory



INIT: version 2.86 booting

Starting the hotplug events dispatcher: udevd[   26.936000] udevd (165): /proc/165/oom_adj is deprecated, please use /proc/165/oom_score_adj instead.
.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...done.
Starting boot logger: bootlogd.

locale: Cannot set LC_CTYPE to default locale: No such file or directory

locale: Cannot set LC_ALL to default locale: No such file or directory

Usage: vt-is-UTF8 [option]

valid options are:

	-q  --quiet    don't print result

	-h --help      display this help text and exit

	-V --version   display version information and exit

Activating swap...[   33.728000] Adding 706824k swap on /dev/sda6.  Priority:-1 extents:1 across:706824k 
done.

Checking root file system...fsck from util-linux 2.20.1

/dev/sda5: clean, 19784/1058832 files, 246687/4227072 blocks

d[   34.540000] EXT3-fs (sda5): using internal journal
one.

Cleaning up temporary files... /tmp /lib/init/rw.

Loading kernel module lasi_82596.

FATAL: Could not load /lib/modules/3.9.0-64bit+/modules.dep: No such file or directory

Loading kernel module loop.

FATAL: Could not load /lib/modules/3.9.0-64bit+/modules.dep: No such file or directory

FATAL: Could not load /lib/modules/3.9.0-64bit+/modules.dep: No such file or directory

Activating lvm and md swap...done.

Checking file systems...fsck from util-linux 2.20.1

/dev/sda2: clean, 19/64256 files, 32964/128520 blocks

done.

Setting kernel variables (/etc/sysctl.conf)...done.

Mounting local filesystems...done.

/etc/rcS.d/S35mountall.sh: line 59: kill: 43 1: arguments must be process or job IDs

Activating swapfile swap...done.

Cleaning up temporary files....

Configuring network interfaces...ifup: failed to open statefile /run/network/ifstate: No such file or directory

failed.

Starting NFS common utilities: statd failed!

Cleaning up temporary files....

Setting console screen modes and fonts.


INIT: Entering runlevel: 2


Starting enhanced syslogd: rsyslogd.

Starting MTA: exim4.

ALERT: exim paniclog /var/log/exim4/paniclog has non-zero size, mail system possibly broken ... failed!

Starting NFS common utilities: statd failed!

Not starting internet superserver: no services enabled.

Starting deferred execution scheduler: atd.

Starting periodic command scheduler: crond.

Stopping boot logger: bootlogd.
[ 1094.884000] kpowerswd: Shutdown requested...
[ 1097.932000] kpowerswd: Shutting down...

INIT: 
IN
INIT: Sending processes the KILL signal

Stopping deferred execution scheduler: atd.
Stopping MTA:.
ALERT: exim paniclog /var/log/exim4/paniclog has non-zero size, mail system possibly broken ... failed!
Stopping NFS common utilities: statd.
Stopping internet superserver: inetd.
Asking all remaining processes to terminate...done.
All processes ended within 1 seconds...done.
Saving the system clock.
Hardware Clock updated to Sun May 12 11:15:53 EST 2013.
Deconfiguring network interfaces...ifdown: failed to open statefile /run/network/ifstate: No such file or directory
failed.
Deactivating swap...done.
Unmounting local filesystems...done.
Will now restart.
[ 1107.724000] sd 1:0:6:0: [sda] Synchronizing SCSI cache
[ 1107.784000] Restarting system.

Reply to: