Re: Newbie : B2000, 2.6.18.dfsg.1-13etch4, boots fine, works fine then later read-only fs
On Thu, Oct 18, 2007 at 02:41:54PM -0600, Matthew Wilcox wrote:
> On Thu, Oct 18, 2007 at 09:31:52PM +0100, Jo Mills wrote:
> > Today, I came back from work, ssh into B2000 from my Sparc to find FS
> > was in read-only mode. Syslog just seems to have gone for a walk part
> > way through logging. OK, re-boot. Comes up fine, I configured
> > exim4-light, did a test e-mail, started to install logcheck and
> > wallop, FS goes read-only again.
>
> What does 'dmesg' tell you happened?
>
Hi Matthew,
The whole dmesg output is some 530 lines, I can send it all if you want but
I think the salient parts are shown below. Is it as straight forward as a
duff disk?
Regards,
Jo.
green:~# dmesg
Linux version 2.6.18-5-parisc (Debian 2.6.18.dfsg.1-13etch4) (dannf@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 Tue Oct 2 23:19:18 UTC 2007
FP[0] enabled: Rev 1 Model 16
The 32-bit Kernel has started...
Initialized PDC Console for debugging.
Determining PDC firmware type: System Map.
model 00005d00 00000481 00000000 00000002 777ee59f 100000f0 00000008 000000b2 000000b2
vers 00000301
CPUID vers 17 rev 11 (0x0000022b)
capabilities 0x3
model 9000/785/B2000
Total Memory: 1024 MB
initrd: 4fb7d000-4ffee8cc
initrd: reserving 3fb7d000-3ffee8cc (mem_max 40000000)
.
.
.
hda: LITE-ON CD-RW SOHR-5239V, ATAPI CD/DVD-ROM drive
ide0 at 0xe00-0xe07,0xd02 on irq 7
Probing IDE interface ide1...
sym0: <895a> rev 0x1 at pci 0000:00:0f.0 irq 68
sym0: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.2.3
hda: ATAPI 52X CD-ROM CD-R/RW drive, 1536kB Cache
Uniform CD-ROM driver Revision: 3.20
Vendor: SEAGATE Model: ST39103LC Rev: HP00
Type: Direct-Access ANSI SCSI revision: 02
target0:0:0: tagged command queuing enabled, command queue depth 16.
target0:0:0: Beginning Domain Validation
target0:0:0: asynchronous
target0:0:0: wide asynchronous
target0:0:0: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 15)
target0:0:0: Domain Validation skipping write tests
target0:0:0: Ending Domain Validation
Vendor: SEAGATE Model: ST39102LC Rev: HP01
Type: Direct-Access ANSI SCSI revision: 02
target0:0:6: tagged command queuing enabled, command queue depth 16.
target0:0:6: Beginning Domain Validation
target0:0:6: asynchronous
target0:0:6: wide asynchronous
target0:0:6: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 15)
target0:0:6: Domain Validation skipping write tests
target0:0:6: Ending Domain Validation
ohci_hcd 0000:00:0e.2: OHCI Host Controller
ohci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0e.2: created debug files
.
.
.
SCSI device sda: 17773524 512-byte hdwr sectors (9100 MB)
sda: Write Protect is off
sda: Mode Sense: 9f 00 10 08
hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000
ohci_hcd 0000:00:0e.2: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
SCSI device sda: drive cache: write through w/ FUA
SCSI device sda: 17773524 512-byte hdwr sectors (9100 MB)
sda: Write Protect is off
sda: Mode Sense: 9f 00 10 08
SCSI device sda: drive cache: write through w/ FUA
sda: sda1 sda2 sda3 < sda5 sda6 >
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 17773524 512-byte hdwr sectors (9100 MB)
sdb: Write Protect is off
sdb: Mode Sense: 9f 00 10 08
SCSI device sdb: drive cache: write through w/ FUA
SCSI device sdb: 17773524 512-byte hdwr sectors (9100 MB)
sdb: Write Protect is off
sdb: Mode Sense: 9f 00 10 08
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
SCSI device sdb: drive cache: write through w/ FUA
sdb: sdb1
sd 0:0:6:0: Attached scsi disk sdb
ohci_hcd 0000:00:0e.2: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
.
.
.
usb 1-2:1.1: uevent
Adding 385520k swap on /dev/sda6. Priority:-1 extents:1 across:385520k
sd 0:0:0:0: SCSI error: return code = 0x000100ff
end_request: I/O error, dev sda, sector 329579
Buffer I/O error on device sda5, logical block 1027
lost page write due to I/O error on sda5
sd 0:0:0:0: ABORT operation started.
sym0: SCSI BUS reset detected.
sym0: SCSI BUS has been reset.
sd 0:0:0:0: ABORT operation complete.
sd 0:0:0:0: ABORT operation started.
sd 0:0:0:0: ABORT operation failed.
sd 0:0:0:0: DEVICE RESET operation started.
sd 0:0:0:0: DEVICE RESET operation complete.
target0:0:0: control msgout: c.
sym0: TARGET 0 has been reset.
target0:0:0: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 15)
EXT3 FS on sda5, internal journal
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: Setting full-duplex based on MII#1 link partner capability of 45e1.
.
.
.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
sd 0:0:0:0: SCSI error: return code = 0x000100ff
end_request: I/O error, dev sda, sector 8859139
Buffer I/O error on device sda5, logical block 1067222
lost page write due to I/O error on sda5
.
.
.
Buffer I/O error on device sda5, logical block 1067229
lost page write due to I/O error on sda5
sd 0:0:0:0: SCSI error: return code = 0x000100ff
end_request: I/O error, dev sda, sector 8859323
Buffer I/O error on device sda5, logical block 1067245
lost page write due to I/O error on sda5
Buffer I/O error on device sda5, logical block 1067246
lost page write due to I/O error on sda5
sd 0:0:0:0: SCSI error: return code = 0x000100ff
end_request: I/O error, dev sda, sector 8859355
sd 0:0:0:0: SCSI error: return code = 0x000100ff
.
.
.
< 200 or so lines of much the same >
.
.
.
end_request: I/O error, dev sda, sector 8709971
sd 0:0:0:0: ABORT operation started.
sym0: SCSI BUS reset detected.
sym0: SCSI BUS has been reset.
sd 0:0:0:0: ABORT operation complete.
sd 0:0:0:0: ABORT operation started.
sd 0:0:0:0: ABORT operation failed.
sd 0:0:0:0: DEVICE RESET operation started.
sd 0:0:0:0: DEVICE RESET operation complete.
target0:0:0: control msgout: c.
sym0: TARGET 0 has been reset.
target0:0:0: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 15)
sd 0:0:0:0: ABORT operation started.
sym0: SCSI BUS reset detected.
sym0: SCSI BUS has been reset.
sd 0:0:0:0: ABORT operation complete.
sd 0:0:0:0: ABORT operation started.
sd 0:0:0:0: ABORT operation failed.
sd 0:0:0:0: DEVICE RESET operation started.
sd 0:0:0:0: DEVICE RESET operation complete.
target0:0:0: control msgout: c.
sym0: TARGET 0 has been reset.
target0:0:0: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 15)
green:~#
Reply to: