C180 Boot problems
First of all, the darn thing hangs when booting after afresh install.
See the following startup output (from my serial console):
HARD Booted.
palo ipl 1.5 root@c3k Fri May 14 16:17:38 MDT 2004
Partition Start(MB) End(MB) Id Type
1 1 31 f0 Palo
2 32 156 83 ext2
5 157 1380 83 ext2
6 1381 1521 82 swap
7 1522 4094 83 ext2
PALO(F0) partition contains:
0/vmlinux32 4968722 bytes @ 0x48000
Information: No console specified on kernel command line. This is normal.
PALO will choose the console currently used by firmware (serial).
Command line for kernel: 'root=/dev/sdb5 HOME=/ console=ttyS0 TERM=vt102
palo_kernel=2/vmlinux'
Selected kernel: /vmlinux from partition 2
Selected ramdisk: /initrd.img from partition 2
ELF32 executable
Entry 00100000 first 00100000 n 3
Segment 0 load 00100000 size 2832408 mediaptr 0x1000
Segment 1 load 003b4000 size 705472 mediaptr 0x2b5000
Segment 2 load 00464000 size 397328 mediaptr 0x362000
Loading ramdisk 4935680 bytes @ 3fb39000...
Branching to kernel entry point 0x00100000. If this is the last
message you see, you may need to switch your console. This is
a common symptom -- search the FAQ and mailing list at parisc-linux.org
Linux version 2.6.8-2-32-smp (kyle@caradhras) (gcc version 3.3.5 (Debian
1:3.3.5-7)) #1 SMP Mon Feb 7 22:19:10 EST 2005
FP[0] enabled: Rev 0 Model 14
The 32-bit Kernel has started...
Determining PDC firmware type: System Map.
model 000059c0 00000481 00000000 00000002 775e4e81 100000f0 00000008 000000b2
000000b2
vers 00000205
CPUID vers 14 rev 9 (0x000001c9)
capabilities 0x2
model 9000/780/C180
Total Memory: 1536 Mb
initrd: 4fb39000-4ffee000
initrd: reserving 3fb39000-3ffee000 (mem_max 60000000)
LED display at f0190001 registered
SMP: bootstrap CPU ID is 0
Built 1 zonelists
Kernel command line: root=/dev/sdb5 HOME=/ console=ttyS0 TERM=vt102
palo_kernel=2/vmlinux
PID hash table entries: 16 (order 4: 128 bytes)
Console: colour dummy device 160x64
Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 131072 (order: 7, 524288 bytes)
Memory: 1572864k available
Calibrating delay loop... 358.80 BogoMIPS
Security Scaffold v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Brought up 1 CPUs
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
NET: Registered protocol family 16
EISA bus registered
Searching for devices...
Found devices:
1. U2-IOA BC Runway Port at 0xfff88000 [8] { 12, 0xf, 0x580, 0x0000b }
2. Dino PCI Bridge at 0xf2000000 [8/0] { 13, 0x1, 0x680, 0x0000a }
3. Raven U/L2 Dino PS/2 Port at 0xf2001000 [8/1] { 10, 0x0, 0x006, 0x00096 }
4. Raven U/L2 Dino RS-232 at 0xf2003000 [8/3] { 10, 0x0, 0x006, 0x0008c }
5. Raven U/L2 Core FW-SCSI at 0xf200c000 [8/12] { 4, 0x0, 0x03b, 0x00089 }
6. Raven U/L2 Core BA at 0xffd00000 [8/16] { 11, 0x0, 0x03b, 0x00081 },
additional addresses: 0xffd0c000 0xffc00000
7. Raven U/L2 Core Centronics at 0xffd02000 [8/16/0] { 10, 0x0, 0x03b, 0x00074
}, additional addresses: 0xffd01000 0xffd03000
8. Raven U/L2 Core Audio at 0xffd04000 [8/16/1] { 10, 0x4, 0x03b, 0x0007b }
9. Raven U/L2 Core RS-232 at 0xffd05000 [8/16/4] { 10, 0x0, 0x03b, 0x0008c }
10. Raven U/L2 Core SCSI at 0xffd06000 [8/16/5] { 10, 0x0, 0x03b, 0x00082 }
11. Raven U/L2 Core LAN (802.3) at 0xffd07000 [8/16/6] { 10, 0x0, 0x03b,
0x0008a }
12. Raven U/L2 Core PS/2 Port at 0xffd08000 [8/16/7] { 10, 0x0, 0x03b, 0x00084
}
13. Raven U/L2 Core PS/2 Port at 0xffd08100 [8/16/8] { 10, 0x0, 0x03b, 0x00084
}
14. Raven U/L2 Core PC Floppy at 0xffd0a000 [8/16/10] { 10, 0x0, 0x03b, 0x00083
}
15. Raven Backplane Wax BA at 0xffe00000 [8/20] { 11, 0x0, 0x017, 0x0008e }
16. Raven Backplane Wax HIL at 0xffe01000 [8/20/1] { 10, 0x0, 0x017, 0x00073 }
17. Raven Backplane RS-232 at 0xffe02000 [8/20/2] { 10, 0x0, 0x017, 0x0008c }
18. Raven Backplane Wax EISA BA at 0xfc000000 [8/20/5] { 11, 0x0, 0x017,
0x00090 }, additional addresses: 0xffc88000 0xfc00000b
19. Gecko GSC Core Graphics at 0xfa000000 [8/24] { 10, 0x0, 0x016, 0x00085 },
additional addresses: 0xf0026000
20. U2-IOA BC GSC+ Port at 0xf203f000 [8/63] { 7, 0x1, 0x501, 0x0000c }
21. U2-IOA BC Runway Port at 0xfff8a000 [10] { 12, 0xf, 0x580, 0x0000b }
22. Coral SGC Graphics at 0xf8000000 [10/8] { 10, 0x0, 0x004, 0x00077 }
23. U2-IOA BC GSC+ Port at 0xf103f000 [10/63] { 7, 0x1, 0x501, 0x0000c }
24. Raven U 180 (9000/780/C180) at 0xfffa0000 [32] { 0, 0x0, 0x59c, 0x00004 }
25. Memory at 0xfffb1000 [49] { 1, 0x0, 0x072, 0x00009 }
CPU(s): 1 x PA8000 (PCX-U) at 180.000000 MHz
Found U2 at 0xfff88000
Found U2 at 0xfff8a000
Lasi version 0 at 0xffd00000 found.
Wax at 0xffe00000 found.
Wax EISA Adapter found at 0xfc000000
EISA EEPROM: cannot register misc device.
Enumerating EISA bus
EISA: Probing bus 0 at parisc8:20:5
EISA: Mainboard HWPC0E1 detected.
EISA: Detected 0 cards.
Dino [8/0] version 2.1 found at 0xf2000000
The GSCtoPCI (Dino hrev 1) bus converter found may exhibit
data corruption. See Service Note Numbers: A4190A-01, A4191A-01.
Systems shipped after Aug 20, 1997 will not exhibit this problem.
Models affected: C180, C160, C160L, B160L, and B132L workstations.
Dino [8/0]: No PCI devices enabled.
SCSI subsystem initialized
TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca)
STI GSC/PCI core graphics driver Version 0.9a
id 2d08c0a7-9a02587, conforms to spec rev. 8.07
graphics card name: INTERNAL_EG_1280
id 2bcb015a-9a02587, conforms to spec rev. 8.04
graphics card name: HPA4071B_LZ
fb0: stifb 1280x1024-8 frame buffer device, INTERNAL_EG_1280, id: 2d08c0a7,
mmio: 0xfa100000
unwind_init: start = 0x103b5720, end = 0x103d6f20, entries = 8576
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
Soft power switch enabled, polling @ 0xf0140000.
Console: switching to colour frame buffer device 160x64
Generic RTC Driver v1.07
Serial: 8250/16550 driver $Revision: 1.90 $ 25 ports, IRQ sharing enabled
ttyS0 at MMIO 0xffd05800 (irq = 90) is a 16550A
ttyS1 at MMIO 0xffe02800 (irq = 121) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
mice: PS/2 mouse device common for all mice
serio: GSC PS2 keyboard port at 0xffd08000 irq 69 @ parisc8:16:7
serio: GSC PS2 mouse port at 0xffd08100 irq 69 @ parisc8:16:8
HP SDC: HP SDC at 0xffe01000, IRQ 126 (NMI IRQ 125)
HP SDC: New style SDC
HP SDC: Revision: 1820-4784
HP SDC: TI SN76494 beeper present
HP SDC: OKI MSM-58321 BBRTC present
HP SDC: Spunking the self test register to force PUP on next firmware reset.
HP SDC MLC: Registering the System Domain Controller's HIL MLC.
The last line is where it freezes.
Also, if I try to boot from the graphics console GRAPHICS(3),
(which is a GSC A4071B) it also freezes, (Right after the line that says
"...common problem..." but the display has thick vertical bars.
What's happening to it?
______________________________________________________
Click here to donate to the Hurricane Katrina relief effort.
http://store.yahoo.com/redcross-donate3/
Reply to: