Problem mit usb-Platten an Sarge-Tjener
Hallo! Ich fahre hier zwei Sarge-Tjener (physikalisch getrennte Netze),
Kernel 2.6.18-4-686 von Backports.org (vorher 2.6.18-3) auf ASUS
P2B-Mainboards. Zur Datensicherung wollte ich USB-Platten einsetzen.
0000:00:04.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
0000:00:09.0 USB Controller: NEC Corporation USB (rev 43)
0000:00:09.1 USB Controller: NEC Corporation USB (rev 43)
0000:00:09.2 USB Controller: NEC Corporation USB 2.0 (rev 04)
Sowohl am Onboard USB 1.1, als auch an der USB 2.0 Karte
bekomme ich beim Anschließen aber nur:
usb 3-4: new high speed USB device using ehci_hcd and address 3
usb 3-4: configuration #1 chosen from 1 choice
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
Vendor: WDC WD25 Model: 00BB-00RDA0 Rev: 0 0
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda:<6>sd 1:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 0
printk: 32 messages suppressed.
Buffer I/O error on device sda, logical block 0
sd 1:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
unable to read partition table
sd 1:0:0:0: Attached scsi disk sda
usb-storage: device scan complete
sd 1:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 488396928
Buffer I/O error on device sda, logical block 61049616
sd 1:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 488396928
Buffer I/O error on device sda, logical block 61049616
sd 1:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 488397160
Buffer I/O error on device sda, logical block 61049645
sd 1:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 488397160
Buffer I/O error on device sda, logical block 61049645
sd 1:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 488397160
Buffer I/O error on device sda, logical block 61049645
sd 1:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 488397160
Buffer I/O error on device sda, logical block 61049645
sd 1:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 488397160
Buffer I/O error on device sda, logical block 61049645
sd 1:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 488397160
Buffer I/O error on device sda, logical block 61049645
sd 1:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 488397104
sd 1:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 488397152
sd 1:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 488397160
sd 1:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 488397160
sd 1:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 0
/schnipp
# 50 gleichlautende Zeilen
schnapp/
sd 1:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 0
sd 1:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 0
Mit einer alten Knoppix 3.3 (Kernel 2.4.irgendwas) sehe ich die Platten!
USB-Stick geht an beiden Controllern. Und die Platten haben ein Netzteil.
Der einzig brauchbare Hinweis, den ich ergoogelt habe ist ein
Kernel-update auf 2.6.20, aber den gibt es wohl nicht für Sarge? Kann
ich problemlos den Etch-Kernel von BPO verwenden?
Hat jemand noch 'nen Tipp?
readU
Frank
Reply to: