在 2010年12月13日 下午6:40，Feng Lu
<0000@mininews.info>写道：
我来挖坟了~~原来之前就有这个问题，我说有点印象呢
这次是ibm x3650m3，LSI megaraid的raid控制器，broadcom的网卡，这两者都不能由businesscard安装盘自动识别安装，通过把驱动文件硬盘塞到businesscard安装光盘里的办法（详见http://im0000.com/?p=1144），能正常安装系统。但是系统安装完成后，不能引导进入，提示找不到硬盘，用同样的办法，把megaraid和bnx2的驱动塞到另台机器上能正常工作的initrd里，能够引导进入系统，但是不能识别网卡，查看dmsg有如下内容
而且在机器开机之后，手动rmmod bnx2然后modprob bnx2重新载入又可以正常工作了
[ 1.993610] Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.7.5 (April 29, 2008)
[ 1.993610] ACPI: PCI Interrupt 0000:0b:00.0[A] -> GSI 28 (level, low) -> IRQ 28
[ 1.993610] PCI: Setting latency timer of device 0000:0b:00.0 to 64
[ 1.993610] firmware: requesting bnx2-09-4.0.5.fw
[ 2.002592] USB Universal Host Controller Interface driver v3.0
[ 2.028776] SCSI subsystem initialized
[ 2.031533] megasas: 00.00.04.31-ieee Thur June 14:13:02 EST 2010
[ 2.038514] No dock devices found.
[ 2.042514] libata version 3.00 loaded.
[ 85.866224] bnx2: Can't load firmware file bnx2-09-4.0.5.fw
[ 85.870165] ACPI: PCI interrupt for device 0000:0b:00.0 disabled
[ 85.870250] bnx2: probe of 0000:0b:00.0 failed with error -2
[ 85.870258] ACPI: PCI Interrupt 0000:0b:00.1[B] -> GSI 40 (level, low) -> IRQ 40
[ 85.870258] PCI: Setting latency timer of device 0000:0b:00.1 to 64
[ 85.870258] firmware: requesting bnx2-09-4.0.5.fw
[ 170.614121] bnx2: Can't load firmware file bnx2-09-4.0.5.fw
[ 170.618067] ACPI: PCI interrupt for device 0000:0b:00.1 disabled
[ 170.618152] bnx2: probe of 0000:0b:00.1 failed with error -2
[ 171.202159] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 17 (level, low) -> IRQ
看起来似乎bnx2的驱动现在确实是需要从硬盘上加载那个bnx2-09-4.0.5.fw的文件，但是失败。如果看模块加载顺序，raid控制器驱动在网卡驱动后面加载，我想是不是假如megaraid_sas模块在bnx2之前加载，是不是就能正常载入呢？求指点。这个模块启动顺序又要如何指定，/etc/modules？
现在下班在家，也不敢随便远程重启机器，先来问问，希望有没去吃饭的朋友答复：）
--
0000@MININEWS.INFO