Bug#339705: installation-reports
Package: installation-reports
Debian-installer-version: Nov. 15, 2005, downloaded with
jigdo-easy2win, not sure from where
uname -a: Linux debianem 2.6.8-2-386 #1 Thu May 19 17:40:50 JST 2005
i686 GNU/Linux
Date: Nov. 17, 21:00
Method: Debian Sarge CD1. Booted from CD.
Machine: No brand
Processor:Pentium III
Memory:128kb
Root Device: IDE /dev/hdd1 ST340016A
/boot on IDE /dev/hda5 FUJITSU MPD3084AT
Root Size/partition table:
Filesystem 1K-blocks Mounted on
/dev/hdd1 3842376 /
/dev/hda5 23302 /boot
/dev/hdd8 6728280 /home
/dev/hdd7 918322 /tmp
/dev/hdd6 6728280 /usr
/dev/hdd5 2885780 /var
Output of lspci and lspci -n:
% lspci
0000:00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
0000:00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)
0000:00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
0000:00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
0000:00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
0000:00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
0000:00:10.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
0000:01:00.0 VGA compatible controller: Cirrus Logic GD 5465 [Laguna] (rev 03)
% lspci -n
0000:00:00.0 0600: 8086:7190 (rev 03)
0000:00:01.0 0604: 8086:7191 (rev 03)
0000:00:07.0 0601: 8086:7110 (rev 02)
0000:00:07.1 0101: 8086:7111 (rev 01)
0000:00:07.2 0c03: 8086:7112 (rev 01)
0000:00:07.3 0680: 8086:7113 (rev 02)
0000:00:10.0 0200: 10ec:8139 (rev 10)
0000:01:00.0 0300: 1013:00d6 (rev 03)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O ]
Configure network HW: [O ]
Config network: [O ]
Detect CD: [O ]
Load installer modules: [O ]
Detect hard drives: [O ]
Partition hard drives: [O ]
Create file systems: [O ]
Mount partitions: [O ]
Install base system: [O ]
Install boot loader: [E ]
Reboot: [E ]
Comments/Problems:
After presumably installing grub in the MBR and rebooting, the screen
became almost unreadable, and after a few messages the boot process
stopped. I was able to boot into the system using a grub floppy and
then the rest of the installation seem to run OK. After the
installation was finished, I ran grub-install manually and rebooted
from the hard disk. I had the same problem. Then I rebooted from the
grub floppy into my old redHat 7.2. I checked the boot partition,
shared between both systems and the grub configuration file grub.conf
was left unmodified. After I added the new kernel and root partition I
was able to boot into debian from the HD. I tried once again to
grub-install and again my system became unbootable from the HD. Thus,
I finally booted from the floppy into RedHat, grub-install'ed and
verified that both Debian and RedHat remained bootable from the HD. It
worries me that I plan on removing RedHat, but I run the risk of
leaving my machine unbootable from the HD if I try to reinstall
Debian.
--
o
W. Luis Mochan | tel:(52)(777)329-1734 /<(*)
Centro de Ciencias Fisicas, UNAM | fax:(52)(777)317-3077 `>/ /\
Apdo. Postal 48-3, 62251 | (52)(777)329-1775 (*)/\/ \
Cuernavaca, Morelos, Mexico |mochan@fis.unam.mx /\_/\__/
Reply to: