Bug#314593: Can't run sparc install with USB keyboard on SB100
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Package: installation-reports
Debian-installer-version: 20050305
uname -a: Linux asok 2.6.8 #1 Wed Feb 2 06:15:12 WST 2005 sparc64
GNU/Linux (commands issued from system running off disc)
Date: Fri, 17 Jun 2005 17:53:48 +0800
Method: cdrom
Machine: SunBlade100
Processor: TI UltraSparc IIe
Memory: 1553104 kB
Root Device: IDE /dev/hda1
Root Size/partition table:
major minor #blocks name
3 0 19551168 hda
3 1 19545120 hda1
3 2 5040 hda2
3 3 19550160 hda3
Output of lspci and lspci -n:
andrewb@asok:~$ lspci
0000:00:00.0 Host bridge: Sun Microsystems Computer Corp. Ultra IIe
0000:00:03.0 Non-VGA unclassified device: ALi Corporation M7101 Power
Management Controller [PMU]
0000:00:05.0 PCI bridge: Digital Equipment Corporation DECchip 21152
(rev 03)
0000:00:07.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge
[Aladdin IV]
0000:00:08.0 Multimedia audio controller: ALi Corporation M5451 PCI
AC-Link Controller Audio Device (rev 01)
0000:00:0c.0 Bridge: Sun Microsystems Computer Corp. RIO EBUS (rev 01)
0000:00:0c.1 Ethernet controller: Sun Microsystems Computer Corp. RIO
GEM (rev 01)
0000:00:0c.2 FireWire (IEEE 1394): Sun Microsystems Computer Corp. RIO
1394 (rev 01)
0000:00:0c.3 USB Controller: Sun Microsystems Computer Corp. RIO USB
(rev 01)
0000:00:0d.0 IDE interface: ALi Corporation M5229 IDE (rev c3)
0000:00:13.0 VGA compatible controller: ATI Technologies Inc Rage XL
(rev 27)
0000:01:02.0 Ethernet controller: Linksys NC100 Network Everywhere Fast
Ethernet 10/100 (rev 11)
andrewb@asok:~$ lspci -n
0000:00:00.0 0600: 108e:a001
0000:00:03.0 0000: 10b9:7101
0000:00:05.0 0604: 1011:0024 (rev 03)
0000:00:07.0 0601: 10b9:1533
0000:00:08.0 0401: 10b9:5451 (rev 01)
0000:00:0c.0 0680: 108e:1100 (rev 01)
0000:00:0c.1 0200: 108e:1101 (rev 01)
0000:00:0c.2 0c00: 108e:1102 (rev 01)
0000:00:0c.3 0c03: 108e:1103 (rev 01)
0000:00:0d.0 0101: 10b9:5229 (rev c3)
0000:00:13.0 0300: 1002:4752 (rev 27)
0000:01:02.0 0200: 1317:0985 (rev 11)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [E]
Configure network HW: [ ]
Config network: [ ]
Detect CD: [ ]
Load installer modules: [ ]
Detect hard drives: [ ]
Partition hard drives: [ ]
Create file systems: [ ]
Mount partitions: [ ]
Install base system: [ ]
Install boot loader: [ ]
Reboot: [ ]
Comments/Problems:
http://ftp.wa.au.debian.org/debian/dists/Debian3.1r0/main/installer-sparc/20050305/
Was trying to boot vmlinuz-2.4.27-2-sparc64 on workstation type machine
with Type 6 USB keyboard which is like PC or Apple USB keyboard.
Trying to use installation set to rescue /dev/ as can no longer boot 2.4
since 2.6 devfs cleaned out mount point so 2.4 will not boot.
The uname -a is the system running on hard disc and not the cdrom as I
could not enter any commands with the cdrom boot.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.1 (GNU/Linux)
iD8DBQFCsqMsm2fZcWJ56s4RAvAqAJ0UEVbGZtNmSs4d83x6N2qu7c0J5wCdE9aZ
4dit30b9h3lQB6LWl8SBrYE=
=hr12
-----END PGP SIGNATURE-----
Reply to: