Re: marvell_cesa continues to fail on kirkwood with kernel 4.4
Thanks for the reply. Can you paste your /proc/crypto as well?
Thanks,
Jan
On Mon, Feb 15, 2016 at 11:25 AM, Rick Thomas <rbthomas@pobox.com> wrote:
>> Here you go...
>>
>>> root@sheeva:~# rmmod mv_cesa
>>> root@sheeva:~# modprobe marvell_cesa allhwsupport=1
>>> root@sheeva:~# dmesg | tail -n 20
>>> [ 16.730426] systemd[1]: Mounted Debug File System.
>>> [ 16.756783] systemd[1]: Started Load Kernel Modules.
>>> [ 16.776948] systemd[1]: Started Create list of required static device nodes for the current kernel.
>>> [ 16.804146] systemd[1]: Started LSB: Set console font and keymap.
>>> [ 17.023950] systemd[1]: Started Journal Service.
>>> [ 18.514731] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro
>>> [ 19.804133] orion_wdt: Initial timeout 21 sec
>>> [ 19.848469] MV-CESA:Could not register sha1 driver
>>> [ 19.848485] MV-CESA:Could not register hmac-sha1 driver
>>> [ 20.379009] systemd-journald[180]: Received request to flush runtime journal from PID 1
>>> [ 20.386082] sd 0:0:0:0: Attached scsi generic sg0 type 0
>>> [ 20.386886] ses 0:0:0:1: Attached scsi generic sg1 type 13
>>> [ 21.518406] EXT4-fs (mmcblk0p1): mounting ext2 file system using the ext4 subsystem
>>> [ 21.682097] EXT4-fs (mmcblk0p1): mounted filesystem without journal. Opts: (null)
>>> [ 22.402713] Adding 9764860k swap on /dev/mapper/sheeva-swap. Priority:-1 extents:1 across:9764860k FS
>>> [ 22.938703] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null)
>>> [ 23.631978] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
>>> [ 27.662122] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
>>> [ 27.662180] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
>>> [ 37.350057] warning: process `colord-sane' used the deprecated sysctl system call with 8.1.2.
>>> root@sheeva:~# uname -a
>>> Linux sheeva 4.4.0-trunk-marvell #1 Debian 4.4.1-1~exp1 (2016-02-10) armv5tel GNU/Linux
>>> root@sheeva:~#
>>
>> For what it's worth, the system boots fine and appears to run OK with the 4.4 kernel.
>>
>> Hope it helps!
>>
>> Rick
>
> A bit more info, incase it helps...
>
> Rick
>
>> root@sheeva:~# cat /proc/cpuinfo
>> processor : 0
>> model name : Feroceon 88FR131 rev 1 (v5l)
>> BogoMIPS : 1185.79
>> Features : swp half thumb fastmult edsp
>> CPU implementer : 0x56
>> CPU architecture: 5TE
>> CPU variant : 0x2
>> CPU part : 0x131
>> CPU revision : 1
>>
>> Hardware : Marvell Kirkwood (Flattened Device Tree)
>> Revision : 0000
>> Serial : 0000000000000000
>> root@sheeva:~#
Reply to: