[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

RE: Cannot boot Freestor 4020 (SS-4000E)



I suppose that it may be that the ramdisk.gz and zimage kernel files I used
are for the SS4000E and will not work in the 4020. The SS4000E uses a 7210
board and the 420 uses a 7220.

Does anyone know if 7220/4020 versions are available anywhere?

CJW

-----Original Message-----
From: Chris Wilkinson [mailto:kinsham@verizon.net] 
Sent: Friday, July 13, 2012 10:04 AM
To: debian-arm@lists.debian.org
Subject: Cannot boot Freestor 4020 (SS-4000E)

It hangs on boot but boots from the console using fis load, exec. There is
one disk is inserted which is disk1/4 of what was the RAID5 set.

Not sure what to try next to get it to boot on its own.

Chris


EM-438/EM-7220 ver.AG0 2006-05-23
== Executing boot script in 1.000 seconds - enter ^C to abort
RedBoot> fis load ramdisk.gz
RedBoot> fis load zImage
RedBoot> exec
Using base address 0x01008000 and length 0x00200000
Uncompressing Linux... done, booting the kernel.
<<hangs here>>


If I start from the console it boots. So it seems the fis images are OK.

Power-on
EM-438/EM-7220 ver.AG0 2006-05-23
== Executing boot script in 1.000 seconds - enter ^C to abort
^C
RedBoot> fis load ramdisk.gz
RedBoot> fis load zImage
RedBoot> exec -c "console=ttyS0,115200 rw root=/dev/ram mem=256M@0xa0000000"
-r 0x01800000 -w 5
About to start execution at 0xa0008000 - abort with ^C within 5 seconds
Using base address 0x01008000 and length 0x00200000
Uncompressing Linux... done, booting the kernel.
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.32-5-iop32x (Debian 2.6.32-45)
(dannf@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 Sun May 6
07:47:32 UTC 2012
[    0.000000] CPU: XScale-80219 [69052e30] revision 0 (ARMv5TE),
cr=0000397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Lanner EM7210
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total
pages: 65024
[    0.000000] Kernel command line: console=ttyS0,115200 rw root=/dev/ram
mem=256M@0xa0000000
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072
bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 256MB = 256MB total
[    0.000000] Memory: 251776KB available (3084K code, 444K data, 112K init,
0K highmem)
[    0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0,
CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:32
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 599.65 BogoMIPS (lpj=2998272)
[    0.220000] Security Framework initialized
[    0.220000] SELinux:  Disabled at boot.
[    0.220000] Mount-cache hash table entries: 512
[    0.220000] Initializing cgroup subsys ns
[    0.220000] Initializing cgroup subsys cpuacct
[    0.220000] Initializing cgroup subsys devices
[    0.220000] Initializing cgroup subsys freezer
[    0.220000] Initializing cgroup subsys net_cls
[    0.220000] CPU: Testing write buffer coherency: ok
[    0.220000] devtmpfs: initialized
[    0.220000] regulator: core version 0.5
[    0.220000] NET: Registered protocol family 16
[    0.220000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.220000] pci 0000:00:01.0: PME# disabled
[    0.220000] pci 0000:00:05.0: PME# supported from D0 D1 D2 D3hot
[    0.220000] pci 0000:00:05.0: PME# disabled
[    0.220000] pci 0000:00:05.1: PME# supported from D0 D1 D2 D3hot
[    0.220000] pci 0000:00:05.1: PME# disabled
[    0.220000] pci 0000:00:05.2: PME# supported from D0 D1 D2 D3hot
[    0.220000] pci 0000:00:05.2: PME# disabled
[    0.220000] PCI: bus0: Fast back to back transfers disabled
[    0.230000] bio: create slab <bio-0> at 0
[    0.230000] vgaarb: loaded
[    0.240000] NET: Registered protocol family 2
[    0.240000] IP route cache hash table entries: 2048 (order: 1, 8192
bytes)
[    0.240000] TCP established hash table entries: 8192 (order: 4, 65536
bytes)
[    0.250000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[    0.250000] TCP: Hash tables configured (established 8192 bind 8192)
[    0.250000] TCP reno registered
[    0.250000] NET: Registered protocol family 1
[    0.250000] Unpacking initramfs...
[    0.950000] Freeing initrd memory: 4096K
[    0.950000] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.950000] audit: initializing netlink socket (disabled)
[    0.950000] type=2000 audit(0.950:1): initialized
[    0.970000] VFS: Disk quotas dquot_6.5.2
[    0.970000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.970000] msgmni has been set to 500
[    0.970000] alg: No test for stdrng (krng)
[    0.970000] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 253)
[    0.970000] io scheduler noop registered
[    0.970000] io scheduler anticipatory registered
[    0.970000] io scheduler deadline registered
[    0.970000] io scheduler cfq registered (default)
[    0.980000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.980000] serial8250.0: ttyS0 at MMIO 0xfe800000 (irq = 28) is a 16550A
[    1.330000] console [ttyS0] enabled
[    1.330000] physmap platform flash device: 02000000 at f0000000
[    1.330000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
[    1.350000]  Intel/Sharp Extended Query Table at 0x0031
[    1.350000]  Intel/Sharp Extended Query Table at 0x0031
[    1.350000] Using buffer write method
[    1.360000] cfi_cmdset_0001: Erase suspend on write enabled
[    1.360000] Searching for RedBoot partition table in physmap-flash.0 at
offset 0x7e0000
[    1.500000] 10 RedBoot partitions found on MTD device physmap-flash.0
[    1.500000] Creating 10 MTD partitions on "physmap-flash.0":
[    1.510000] 0x000000000000-0x000000040000 : "RedBoot"
[    1.510000] 0x000000040000-0x000000240000 : "zImage"
[    1.520000] 0x000000240000-0x000000640000 : "ramdisk.gz"
[    1.530000] 0x000000640000-0x000000700000 : "wmdata"
[    1.530000] 0x000000700000-0x000000740000 : "rammode"
[    1.540000] 0x000000740000-0x000000760000 : "naskey"
[    1.550000] 0x000000760000-0x0000007a0000 : "log"
[    1.550000] 0x0000007a0000-0x0000007c0000 : "vendor"
[    1.560000] 0x0000007c0000-0x0000007c1000 : "RedBoot config"
[    1.560000] mtd: partition "RedBoot config" doesn't end on an erase block
-- force read-only
[    1.580000] 0x0000007e0000-0x000000800000 : "FIS directory"
[    1.580000] mice: PS/2 mouse device common for all mice
[    1.590000] i2c /dev entries driver
[    1.590000] rtc-rs5c372 0-0032: rs5c372a found, 24hr, driver version 0.6
[    1.610000] rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
[    1.610000] i2c i2c-0: failed,FF11,11,05
[    1.640000] iop-adma iop-adma.0: Intel(R) IOP: ( cpy intr )
[    1.660000] iop-adma iop-adma.1: Intel(R) IOP: ( cpy intr )
[    1.660000] TCP cubic registered
[    1.670000] NET: Registered protocol family 17
[    1.670000] XScale DSP coprocessor detected.
[    1.680000] registered taskstats version 1
[    1.680000] rtc-rs5c372 0-0032: setting system clock to 2012-07-13
16:50:50 UTC (1342198250)
[    1.700000] Initalizing network drop monitor service
[    1.700000] Freeing init memory: 112K
Loading, please wait...
[    1.960000] udev[39]: starting version 164
[    2.940000] SCSI subsystem initialized
[    3.230000] scsi0 : sata_vsc
[    3.240000] scsi1 : sata_vsc
[    3.240000] scsi2 : sata_vsc
[    3.250000] scsi3 : sata_vsc
[    3.250000] ata1: SATA max UDMA/133 mmio m4096@0x80060000 port 0x80060200
irq 29
[    3.260000] ata2: SATA max UDMA/133 mmio m4096@0x80060000 port 0x80060400
irq 29
[    3.270000] ata3: SATA max UDMA/133 mmio m4096@0x80060000 port 0x80060600
irq 29
[    3.270000] ata4: SATA max UDMA/133 mmio m4096@0x80060000 port 0x80060800
irq 29
[    3.640000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    3.670000] ata1.00: ATA-8: WDC WD5000AAKS-00UU3A0, 01.03B01, max
UDMA/133
[    3.670000] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[    3.700000] ata1.00: configured for UDMA/133
[    3.700000] scsi 0:0:0:0: Direct-Access     ATA      WDC WD5000AAKS-0
01.0 PQ: 0 ANSI: 5
[    4.060000] ata2: SATA link down (SStatus 0 SControl 300)
[    4.410000] ata3: SATA link down (SStatus 0 SControl 300)
[    4.760000] ata4: SATA link down (SStatus 0 SControl 300)
[    4.870000] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500
GB/465 GiB)
[    4.880000] sd 0:0:0:0: [sda] Write Protect is off
[    4.880000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[    4.900000]  sda: sda1 sda2 sda3 < sda5 >
[    4.950000] sd 0:0:0:0: [sda] Attached SCSI disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ...
Begin: Loading[    5.750000] md: raid1 personality registered for level 1
Success: loaded module raid1.
done.
Begin: Assembling all MD arrays ... [    5.800000] mdadm: sending ioctl 1261
to a partition!
[    5.810000] mdadm: sending ioctl 1261 to a partition!
[    5.810000] mdadm: sending ioctl 1261 to a partition!
[    5.820000] mdadm: sending ioctl 1261 to a partition!
[    5.820000] mdadm: sending ioctl 1261 to a partition!
[    5.830000] mdadm: sending ioctl 1261 to a partition!
[    5.840000] mdadm: sending ioctl 1261 to a partition!
[    5.840000] mdadm: sending ioctl 1261 to a partition!
[    5.850000] mdadm: sending ioctl 800c0910 to a partition!
[    5.850000] mdadm: sending ioctl 800c0910 to a partition!
Failure: failed to assemble all arrays.
done.
done.
Begin: Running /scripts/local-premount ... done.
[    6.320000] kjournald starting.  Commit interval 5 seconds
[    6.330000] EXT3 FS on sda2, internal journal
[    6.340000] EXT3-fs: mounted filesystem with ordered data mode.
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.

INIT: version 2.88 booting

Using makefile-style concurrent boot in runlevel S.
Starting the hotplug events dispatcher: udevd[    8.050000] udev[151]:
starting version 164
.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...[    9.420000] Intel(R) PRO/1000
Network Driver - version 7.3.21-k5-NAPI
[    9.420000] Copyright (c) 1999-2006 Intel Corporation.
[    9.800000] e1000: 0000:00:01.0: e1000_probe: (PCI:33MHz:32-bit)
00:02:41:00:94:7f
[   10.020000] usbcore: registered new interface driver usbfs
[   10.020000] usbcore: registered new interface driver hub
[   10.120000] usbcore: registered new device driver usb
[   10.190000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   10.390000] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network
Connection
[   10.430000] ehci_hcd 0000:00:05.2: EHCI Host Controller
[   10.430000] ehci_hcd 0000:00:05.2: new USB bus registered, assigned bus
number 1
[   10.450000] ehci_hcd 0000:00:05.2: Enabling legacy PCI PM
[   10.490000] ehci_hcd 0000:00:05.2: irq 27, io mem 0x80063000
[   10.510000] ehci_hcd 0000:00:05.2: USB 2.0 started, EHCI 1.00
[   10.510000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   10.520000] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[   10.530000] usb usb1: Product: EHCI Host Controller
[   10.530000] usb usb1: Manufacturer: Linux 2.6.32-5-iop32x ehci_hcd
[   10.540000] usb usb1: SerialNumber: 0000:00:05.2
[   10.550000] usb usb1: configuration #1 chosen from 1 choice
[   10.550000] hub 1-0:1.0: USB hub found
[   10.560000] hub 1-0:1.0: 5 ports detected
[   10.750000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   10.770000] ohci_hcd 0000:00:05.0: OHCI Host Controller
[   10.770000] ohci_hcd 0000:00:05.0: new USB bus registered, assigned bus
number 2
[   10.780000] ohci_hcd 0000:00:05.0: irq 30, io mem 0x80061000
[   10.880000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[   10.880000] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[   10.900000] usb usb2: Product: OHCI Host Controller
[   10.900000] usb usb2: Manufacturer: Linux 2.6.32-5-iop32x ohci_hcd
[   10.900000] usb usb2: SerialNumber: 0000:00:05.0
[   10.930000] usb usb2: configuration #1 chosen from 1 choice
[   10.960000] hub 2-0:1.0: USB hub found
[   10.960000] hub 2-0:1.0: 3 ports detected
[   10.980000] ohci_hcd 0000:00:05.1: OHCI Host Controller
[   11.010000] ohci_hcd 0000:00:05.1: new USB bus registered, assigned bus
number 3
[   11.010000] ohci_hcd 0000:00:05.1: irq 29, io mem 0x80062000
[   11.140000] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[   11.140000] usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[   11.150000] usb usb3: Product: OHCI Host Controller
[   11.150000] usb usb3: Manufacturer: Linux 2.6.32-5-iop32x ohci_hcd
[   11.170000] usb usb3: SerialNumber: 0000:00:05.1
[   11.180000] usb usb3: configuration #1 chosen from 1 choice
[   11.190000] hub 3-0:1.0: USB hub found
[   11.190000] hub 3-0:1.0: 2 ports detected
done.
Activating swap...[   11.810000] Adding 748536k swap on /dev/sda5.
Priority:-1 extents:1 across:748536k 
done.
Checking root file system...fsck from util-linux-ng 2.17.2
e2fsck 1.41.12 (17-May-2010)
/dev/sda2: clean, 27294/30466048 files, 2115481/121846528 blocks
done.
[   13.180000] EXT3 FS on sda2, internal journal
[   13.760000] loop: module loaded
Cleaning up ifupdown....
Loading kernel modules...done.
[   13.990000] __ratelimit: 30 callbacks suppressed
[   14.000000] mdadm: sending ioctl 800c0910 to a partition!
[   14.000000] mdadm: sending ioctl 800c0910 to a partition!
[   14.030000] mdadm: sending ioctl 800c0910 to a partition!
[   14.030000] mdadm: sending ioctl 800c0910 to a partition!
[   14.050000] mdadm: sending ioctl 1261 to a partition!
[   14.050000] mdadm: sending ioctl 1261 to a partition!
[   14.080000] mdadm: sending ioctl 1261 to a partition!
[   14.090000] mdadm: sending ioctl 1261 to a partition!
[   14.100000] mdadm: sending ioctl 1261 to a partition!
[   14.100000] mdadm: sending ioctl 1261 to a partition!
Generating udev events for MD arrays...done.
Setting up networking....
Activating lvm and md swap...done.
Checking file systems...fsck from util-linux-ng 2.17.2
e2fsck 1.41.12 (17-May-2010)
/dev/sda1: clean, 17/124496 files, 20609/248832 blocks
done.
Mounting local filesystems...done.
Activating swapfile swap...done.
Cleaning up temporary files....
Setting kernel variables ...done.
Configuring network interfaces...done.
Starting portmap daemon....
Starting NFS common utilities: statd.
Cleaning up temporary files....

INIT: Entering runlevel: 2

[   18.170000] e1000: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow
Control: RX/TX
Using makefile-style concurrent boot in runlevel 2.
Starting portmap daemon...Already running..
Starting NFS common utilities: statd.
[   19.470000] RPC: Registered udp transport module.
[   19.470000] RPC: Registered tcp transport module.
[   19.480000] RPC: Registered tcp NFSv4.1 backchannel transport module.
Starting enhanced syslogd: rsyslogd.
[   20.580000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   22.320000] NET: Registered protocol family 10
[   22.340000] svc: failed to register lockdv1 RPC service (errno 97).
[   22.400000] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state
recovery directory
[   22.430000] NFSD: starting 90-second grace period
Starting Samba daemons: nmbd smbd.
Exporting directories for NFS kernel daemon....
Starting NFS kernel daemon: nfsd mountd.
Starting web server: apache2.
Starting deferred execution scheduler: atd.
Starting system message bus: dbus.
Starting periodic command scheduler: cron.
Starting MTA:Starting MD monitoring service: mdadm --monitor.
Starting internet superserver: inetd.
Starting OpenBSD Secure Shell server: sshd.
Starting the Winbind daemon: winbind.
 exim4.

Debian GNU/Linux 6.0 fsFreedom9 ttyS0

fsFreedom9 login: root
Password:                                           <<it knew my old
password!!>>
Last login: Fri Jul 13 12:38:13 EDT 2012 on ttyS0
Linux fsFreedom9 2.6.32-5-iop32x #1 Sun May 6 07:47:32 UTC 2012 armv5tel

The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
root@fsFreedom9:~# pwd
/root
root@fsFreedom9:~#

Best Regards
Chris Wilkinson
301 277 2871



-- 
To UNSUBSCRIBE, email to debian-arm-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact
listmaster@lists.debian.org
Archive: 000001cd6100$678758b0$36960a10$@net">http://lists.debian.org/000001cd6100$678758b0$36960a10$@net


Reply to: