sheeva plug usb install
Dear All,
I have installed debian on a usb memory stick using the instructions
from http://www.cyrius.com/debian/kirkwood/sheevaplug/install.html. I
did a standard installation in a single partition.
When I try to boot it seems to go well getting as far as running the run
level 2 start-up scripts. But after that nothing. I suspect it should
provide me with a login prompt at this point but I do not know why it
has stalled.
I have included the boot messages below. Can anyone offer any suggestions?
Regards,
Stewart
5684111 bytes read
## Booting image at 00800000 ...
Image Name: Debian kernel
Created: 2010-11-09 20:45:41 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1432308 Bytes = 1.4 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
Image Name: Debian ramdisk
Created: 2010-11-09 20:45:42 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5684047 Bytes = 5.4 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-5-kirkwood (Debian 2.6.32-27)
(maks@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 Sun Oct 31
11:19:32 UTC 2010
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE),
cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Marvell SheevaPlug Reference Board
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 130048
[ 0.000000] Kernel command line: console=ttyS0,115200
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.000000] Memory: 256MB 256MB = 512MB total
[ 0.000000] Memory: 509568KB available (3512K code, 583K data, 124K
init, 0K highmem)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0,
CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:114
[ 0.000000] Console: colour dummy device 80x30
[ 21.474959] Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776)
[ 21.714922] Security Framework initialized
[ 21.714940] SELinux: Disabled at boot.
[ 21.714965] Mount-cache hash table entries: 512
[ 21.715257] Initializing cgroup subsys ns
[ 21.715273] Initializing cgroup subsys cpuacct
[ 21.715283] Initializing cgroup subsys devices
[ 21.715292] Initializing cgroup subsys freezer
[ 21.715300] Initializing cgroup subsys net_cls
[ 21.715355] CPU: Testing write buffer coherency: ok
[ 21.716078] devtmpfs: initialized
[ 21.717784] regulator: core version 0.5
[ 21.717991] NET: Registered protocol family 16
[ 21.718486] Kirkwood: MV88F6281-A1, TCLK=200000000.
[ 21.718498] Feroceon L2: Enabling L2
[ 21.718531] Feroceon L2: Cache support initialised.
[ 21.720364] bio: create slab <bio-0> at 0
[ 21.720627] vgaarb: loaded
[ 21.721074] Switching to clocksource orion_clocksource
[ 21.724681] NET: Registered protocol family 2
[ 21.724972] IP route cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 21.725733] TCP established hash table entries: 16384 (order: 5,
131072 bytes)
[ 21.726087] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 21.726266] TCP: Hash tables configured (established 16384 bind 16384)
[ 21.726275] TCP reno registered
[ 21.726423] NET: Registered protocol family 1
[ 21.726591] Unpacking initramfs...
[ 22.089897] Freeing initrd memory: 5548K
[ 22.090006] NetWinder Floating Point Emulator V0.97 (double precision)
[ 22.090247] audit: initializing netlink socket (disabled)
[ 22.090281] type=2000 audit(0.600:1): initialized
[ 22.096689] VFS: Disk quotas dquot_6.5.2
[ 22.096952] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 22.097045] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat,
Inc.
[ 22.097680] msgmni has been set to 1006
[ 22.099298] alg: No test for stdrng (krng)
[ 22.099417] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 253)
[ 22.099429] io scheduler noop registered
[ 22.099436] io scheduler anticipatory registered
[ 22.099443] io scheduler deadline registered
[ 22.099620] io scheduler cfq registered (default)
[ 22.105557] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 22.106013] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 22.424973] console [ttyS0] enabled
[ 22.429032] NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc
(Samsung NAND 512MiB 3,3V 8-bit)
[ 22.437730] Scanning device for bad blocks
[ 22.561496] Creating 3 MTD partitions on "orion_nand":
[ 22.566663] 0x000000000000-0x000000100000 : "u-boot"
[ 22.572215] 0x000000100000-0x000000500000 : "uImage"
[ 22.577650] 0x000000500000-0x000020000000 : "root"
[ 22.583888] mice: PS/2 mouse device common for all mice
[ 22.589367] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[ 22.595311] i2c /dev entries driver
[ 22.599013] cpuidle: using governor ladder
[ 22.603257] cpuidle: using governor menu
[ 22.607293] Registered led device: plug:green:health
[ 22.612348] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[ 22.618747] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
[ 22.661135] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 22.701132] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[ 22.741132] mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
[ 22.781132] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
[ 22.787791] TCP cubic registered
[ 22.791033] NET: Registered protocol family 17
[ 22.795834] registered taskstats version 1
[ 22.800561] rtc-mv rtc-mv: setting system clock to 2010-11-10
20:59:30 UTC (1289422770)
[ 22.808621] Initalizing network drop monitor service
[ 22.813673] Freeing init memory: 124K
Loading, please wait...
[ 22.891537] udev[44]: starting version 163
[ 23.173398] MV-643xx 10/100/1000 ethernet driver version 1.4
[ 23.179346] mv643xx_eth smi: probed
[ 23.230520] usbcore: registered new interface driver usbfs
[ 23.241472] usbcore: registered new interface driver hub
[ 23.248315] net eth0: port 0 with MAC address 00:50:43:05:13:1b
[ 23.254782] mmc0: mvsdio driver initialized, lacking card detect
(fall back to polling)
[ 23.267563] usbcore: registered new device driver usb
[ 23.286768] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 23.293407] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 23.298708] orion-ehci orion-ehci.0: new USB bus registered, assigned
bus number 1
[ 23.331121] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 23.351106] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 23.359055] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 23.365909] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 23.373172] usb usb1: Product: Marvell Orion EHCI
[ 23.377897] usb usb1: Manufacturer: Linux 2.6.32-5-kirkwood ehci_hcd
[ 23.384288] usb usb1: SerialNumber: orion-ehci.0
[ 23.389803] usb usb1: configuration #1 chosen from 1 choice
[ 23.395752] hub 1-0:1.0: USB hub found
[ 23.399550] hub 1-0:1.0: 1 port detected
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top
... done.
Begin: Waiting for root file system ... [ 23.721122] usb 1-1: new high
speed USB device using orion-ehci and address 2
[ 23.872017] usb 1-1: New USB device found, idVendor=0781, idProduct=5204
[ 23.878757] usb 1-1: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 23.885948] usb 1-1: Product: Cruzer Crossfire
[ 23.890414] usb 1-1: Manufacturer: SanDisk Corporation
[ 23.895593] usb 1-1: SerialNumber: 2004110202188FF06501
[ 23.902123] usb 1-1: configuration #1 chosen from 1 choice
[ 23.989852] SCSI subsystem initialized
[ 24.016619] Initializing USB Mass Storage driver...
[ 24.021792] scsi0 : SCSI emulation for USB Mass Storage devices
[ 24.028433] usbcore: registered new interface driver usb-storage
[ 24.035092] USB Mass Storage support registered.
[ 29.032106] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Crossfire
2.0 PQ: 0 ANSI: 2
[ 29.070051] sd 0:0:0:0: [sda] 4012467 512-byte logical blocks: (2.05
GB/1.91 GiB)
[ 29.078035] sd 0:0:0:0: [sda] Write Protect is off
[ 29.082892] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 29.091286] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 29.097416] sda: sda1 sda2 sda3 < sda5 >
[ 29.106786] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 29.112936] sd 0:0:0:0: [sda] Attached SCSI removable disk
done.
Begin: Running /scripts/local-premount ... done.
[ 29.368806] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 29.375228] EXT3-fs: write access will be enabled during recovery.
[ 32.168972] kjournald starting. Commit interval 5 seconds
[ 32.174525] EXT3-fs: recovery complete.
[ 32.294670] EXT3-fs: mounted filesystem with ordered data mode.
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
Using makefile-style concurrent boot in runlevel S.
Starting the hotplug events dispatcher: udevd[ 32.831275] udev[234]:
starting version 163
.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...done.
Activating swap...[ 33.487513] Adding 145400k swap on /dev/sda5.
Priority:-1 extents:1 across:145400k
done.
Checking root file system...fsck from util-linux-ng 2.17.2
e2fsck 1.41.12 (17-May-2010)
/dev/sda2: clean, 22324/106080 files, 127711/423936 blocks
done.
[ 33.625104] EXT3 FS on sda2, internal journal
[ 33.811317] loop: module loaded
Loading kernel modules...done.
Cleaning up ifupdown....
Setting up networking....
Activating lvm and md swap...done.
Checking file systems...fsck from util-linux-ng 2.17.2
e2fsck 1.41.12 (17-May-2010)
/dev/sda1 was not cleanly unmounted, check forced.
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda1: 19/81440 files (10.5% non-contiguous), 25275/162816 blocks
fsck died with exit status 1
done.
Mounting local filesystems...done.
Activating swapfile swap...done.
Cleaning up temporary files....
Configuring network interfaces...Setting kernel variables ...done.
done.
Starting portmap daemon....
Starting NFS common utilities: statd.
Cleaning up temporary files....
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Starting portmap daemon...Already running..
Starting NFS common utilities: statd.
Starting enhanced syslogd: rsyslogd.
Starting deferred execution scheduler: atd.
Starting periodic command scheduler: cron.
Starting MTA: exim4.
[ 37.194121] NET: Registered protocol family 10
[ 37.200091] lo: Disabled Privacy Extensions
[ 37.227367] ADDRCONF(NETDEV_UP): eth0: link is not ready
Running scripts in rc2.d/ took 1 seconds.
Reply to: