Sheevaplug: Squeeze on SD won't boot on power up
I have a strange problem, or at least one that Google doesn't help me find an answer too.
I have installed Squeeze on an SD card following the excellent web site by Martin Michlmayr.
However, my Sheevaplug won't boot after being powered on. If I type "run bootcmd" atthe Marvell>> prompt, it *does* boot just fine!
After power up, the boot fails so fast that all I (sometimes) get a glimpse of is:
Error! cmd : 8, err : 0201
Error! cmd : 1, err : 0201
Error! cmd : 1, err : 0201
Error! cmd : 1, err : 0201
Error! cmd : 1, err : 0201
Error! cmd : 1, err : 0201
Error! cmd : 1, err : 0201
Error! cmd : 1, err : 0201
Error! cmd : 1, err : 0201
Error! cmd : 1, err : 0201
Error! cmd : 1, err : 0201
No MMC card found
** Bad partition 1 **
** Bad partition 1 **
## Booting image at 00800000 ...
Bad Magic Number
Marvell>>
If I issue a printenv, I get the results shown below.
What is going on?
The plug runs fine after this manual boot command, but I can't have a serial connection to it all the time!
Thank,
Mark
printenv results follow:
Marvell>> printenv
baudrate=115200
loads_echo=0
rootpath=/mnt/ARM_FS/
netmask=255.255.0.0
console=a0000
e=ttyS0,115200
CASset=min
MALLOC_len=1
ethprime=egiga0
bootargs_root=root=/dev/mtdblock2 ro
ethmtu=1500
usb0Mode=host
nandEcc=1bit
ethact=egiga0
serverip=10.10.0.2
ipaddr=10.10.0.1
cesvcid=ULULULULULULPPULULULULULDA
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/m
tdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
ethaddr=00:50:43:01:47:74
run_diag=no
arcNumber=2097
bootcmd_m0000=0x01100000
bootargs_console=console=ttyS0,115200
bootcmd_mmc=mmcinit; ext2load mmc 0 0x01100000 /uInitrd; ext2load mmc 0 0x00800000 /uImage
bootcmd=setenv bootargs $(bootargs_console); run bootcmd_mmc; bootm 0x00800000 0x01100000
stdin=serial
stdout=serial
stderr=serial
nandEnvBase=a0000
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
bootargs=console=ttyS0,115200
Environment size: 1366/131068 bytes
Reply to: