[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Clean sid? install to Tyan k8we



I have succeeded a clean sid install to Tyan k8we as follows:

Debian-installer-version: debian-testing-amd64-businesscard dated 10/04/05  
http://cdimage.debian.org/pub/cdimage-testing/daily/amd64/current/debian-testing-amd64-businesscard.iso

uname -a: 2.6.12-1-amd64-k8-smp

Date: Oct 5th, 2005 around 3:00 AM JST

Method: <How did you install? What did you boot off?>
   Boot off from the burnt iso image above.

<If network install, from where?  Proxied?>
   http://ftp.jp.debian.org/debian-amd64/debian/   no proxies

Machine: <Description of machine (eg, IBM Thinkpad R32)>
   DIY WS based on Tyan k8we w/o SCSI

Processor: Dual Opteron 265

Memory: SanMax ECC Registered Memory 512MB x 4

Root Device: <IDE?  SCSI?  Name of device?> SATA0 /dev/sdb2

Root Size/partition table: <Feel free to paste the full partition
      table, with notes on which partitions are mounted where.>
   /dev/sdb1 32GB is mounted as a swap
   /dev/sdb2 32GB is mounted as root

Output of lspci:

0000:00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev
a3)
0000:00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev a3)
0000:00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2)
0000:00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2)
0000:00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3)
0000:00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev a2)
0000:00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev
a3)
0000:00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev
a3)
0000:00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev a2)
0000:00:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev a3)
0000:00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller
0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
0000:00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
0000:00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
0000:00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller
0000:00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
0000:02:00.0 VGA compatible controller: nVidia Corporation NV43 [GeForce 6600
GT] (rev a2)
0000:08:0a.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge
(rev 12)
0000:08:0a.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC (rev 01)
0000:08:0b.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge
(rev 12)
0000:08:0b.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC (rev 01)
0000:80:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev
a3)
0000:80:01.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev
a3)
0000:80:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev a3)
0000:80:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
0000:81:00.0 VGA compatible controller: nVidia Corporation NV43 [GeForce 6600
GT] (rev a2)


Output of lspci -n:
0000:00:00.0 0580: 10de:005e (rev a3)
0000:00:01.0 0601: 10de:0051 (rev a3)
0000:00:01.1 0c05: 10de:0052 (rev a2)
0000:00:02.0 0c03: 10de:005a (rev a2)
0000:00:02.1 0c03: 10de:005b (rev a3)
0000:00:06.0 0101: 10de:0053 (rev a2)
0000:00:07.0 0101: 10de:0054 (rev a3)
0000:00:08.0 0101: 10de:0055 (rev a3)
0000:00:09.0 0604: 10de:005c (rev a2)
0000:00:0a.0 0680: 10de:0057 (rev a3)
0000:00:0e.0 0604: 10de:005d (rev a3)
0000:00:18.0 0600: 1022:1100
0000:00:18.1 0600: 1022:1101
0000:00:18.2 0600: 1022:1102
0000:00:18.3 0600: 1022:1103
0000:00:19.0 0600: 1022:1100
0000:00:19.1 0600: 1022:1101
0000:00:19.2 0600: 1022:1102
0000:00:19.3 0600: 1022:1103
0000:02:00.0 0300: 10de:0140 (rev a2)
0000:08:0a.0 0604: 1022:7450 (rev 12)
0000:08:0a.1 0800: 1022:7451 (rev 01)
0000:08:0b.0 0604: 1022:7450 (rev 12)
0000:08:0b.1 0800: 1022:7451 (rev 01)
0000:80:00.0 0580: 10de:005e (rev a3)
0000:80:01.0 0580: 10de:00d3 (rev a3)
0000:80:0a.0 0680: 10de:0057 (rev a3)
0000:80:0e.0 0604: 10de:005d (rev a3)
0000:81:00.0 0300: 10de:0140 (rev a2)


Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it

Initial boot worked:    [O]
Configure network HW:   [O]
Config network:         [O]
Detect CD:              [O]
Load installer modules: [O]
Detect hard drives:     [O]
Partition hard drives:  [ ]
Create file systems:    [O]
Mount partitions:       [O]
Install base system:    [E]
Install boot loader:    [ ]
Reboot:                 [ ]

Comments/Problems:

<Description of the install, in prose, and any thoughts, comments
      and ideas you had during the initial install.>
Install errs at "Installing the base system" after the choice of kernel.  I
completed the installation proces by means of chroot install.  After the
error, I enter alternate screen by Alt-F2.  Then after hitting return
   a. # mount -t proc proc /target/proc
   b. # chroot /target /bin/bash
   c. # mount -a
   d. # gpg --keyserver keyring.debian.org --recv 4F368D5D
   e. # apt-get update     (still errs!)
   f. # gpg --no-default-keyring --keyring /etc/apt/trusted.gpg --recv-key
E415B2B4B5F5BBED
   g. # apt-get update
   h. # apt-get install linux-image-2.6.12-1-amd64-k8-smp lilo initrd-tools
cramfsprogs dash
   i. # umount -a
   j. # exit
   k. # umount /target/proc
   l. # reboot


The following are my comments:
1. At "Configure time zone", I cannot select time-zone.  Using tzconfig, I must
do it later.
2. After reboot, I need to modprobe some modules.  For example, I need
forcedeth for my networking.  I must write /etc/modules to avoid modprobe.
3. I invoked 2nd stage installer manually:
   # base-config
4. etch installation is described at debian-boot mailing list:
   http://lists.debian.org/debian-boot/2005/10/msg00091.html

The following are helpful:
   http://www.debian-administration.org/articles/174
   http://www.64bit-world.com/forums/archive/index.php/t-4080.html

Toshikazu Aiyama



		
__________________________________ 
Yahoo! Mail - PC Magazine Editors' Choice 2005 
http://mail.yahoo.com



Reply to: