Re: kernel-image packages for alpha in need of testing
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
> I've repeated the test with this new image and the qlogic-driver doesn't
> fail anymore. When it comes to initialize the network, it cannot retrieve
> its settings via DHCP, also manual assignment doesn't help. It cannot get
> connection to any other computer through the network. Your patch probably
> affected the tulip and 3c59x module (which I use in my alpha).
I use the tulip driver for my '0000:00:14.0 PCI bridge: Digital Equipment
Corporation DECchip 21152 (rev 02)' card on my PWS500au. It is configured
via DHCP. Reverting the changes to 'arch/alpha/linux/core_cia.c' in Debian
kernel 2.6.6 didn't cause any problems with it.
The relevant boot lines are:
SCSI subsystem initialized
ERROR: SCSI host `isp1020' has no error handling
ERROR: This is not a safe way to run your SCSI host
ERROR: The error handling must be added to this driver
fffffc000098fde8 fffffffc00225cd8 fffffffc0023a12c fffffffc00226890
fffffffc00226890 fffffc0017edd000 0000000000000000 0000000000000000
fffffc0000000000 fffffc000098fe30 fffffc000098fe30 fffffc0017edd000
fffffffc00210047 fffffc0000561300 fffffffc0021a068 fffffc0000561300
fffffffc00226890 fffffffc00226890 fffffffc001f0074 fffffc0000561300
fffffffc00226890 fffffc0000561300 fffffffc00226968 fffffc00005686c0
Trace:fffffc0000349adc fffffc0000314b84
qlogicisp : new isp1020 revision ID (5)
scsi0 : QLogic ISP1020 SCSI on PCI bus 01 device 48 irq 40 I/O base 0x8000
Using anticipatory io scheduler
Vendor: DEC Model: RZ1CC-BA (C) DEC Rev: 883F
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 8380080 512-byte hdwr sectors (4291 MB)
SCSI device sda: drive cache: write through
/dev/scsi/host0/bus0/target0/lun0: p1 p2 p3
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Vendor: IOMEGA Model: ZIP 100 Rev: J.03
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sdb at scsi0, channel 0, id 6, lun 0
---<snip>---
tulip0: EEPROM default media type Autosense.
tulip0: Index #0 - Media 10baseT (#0) described by a 21142 Serial PHY (2)
block.
tulip0: Index #1 - Media 10baseT-FDX (#4) described by a 21142 Serial PHY (2)
block.
tulip0: Index #2 - Media 10base2 (#1) described by a 21142 Serial PHY (2)
block.
tulip0: Index #3 - Media AUI (#2) described by a 21142 Serial PHY (2) block.
tulip0: Index #4 - Media MII (#11) described by a 21142 MII PHY (3) block.
tulip0: MII transceiver #5 config 0000 status 784d advertising 01e1.
eth0: Digital DS21143 Tulip rev 48 at 0x9000, 00:00:F8:75:A3:EE, IRQ 24.
- -T
- --
Tyson Whitehead (-twhitehe@uwo.ca -- WSC-)
Computer Engineer Dept. of Applied Mathematics,
Graduate Student- Applied Mathematics University of Western Ontario,
GnuPG Key ID# 0x8A2AB5D8 London, Ontario, Canada
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.4 (GNU/Linux)
iD8DBQFA1ZL6RXbLmIoqtdgRAuGcAKDjYsbExnaCejjrw6ab6sDXO5z9OwCgt1L0
/YwnGcd4bWdLsPQMFASZ1oE=
=lLpd
-----END PGP SIGNATURE-----
Reply to: