MVME162, The saga continues.....
Debian folks:
The FPU was the culprit, When I grab a card with FPU it boots to the
Debian installer. Not altogether well yet, fdisk states
Your system is not supported yet!
# dmesg
MVME162 Hardware status:
CPU Type 68040
CPU clock 32MHz
VMEchip2 present
SCSI interface present
Ethernet interface present
Calibrating delay loop.. ok - 21.24 BogoMIPS
Memory: 14536k/16384k available (648k kernel code, 564k data)
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: ICMP, UDP, TCP
VFS: Diskquotas version dquot_5.6.0 initialized
Linux version 2.0.36 (root@flash) (gcc version 2.7.2.3) #1 Sat Feb 13
02:45:31 GMT 1999
Starting kswapd v 1.4.2.2
M68K Serial driver version 1.01
ttyS1 at 0xfff45001: SCC w/o DMA
ttyS0 at 0xfff45005: SCC w/o DMA
Ramdisk driver initialized : 16 ramdisks of 4096K size
loop: registered device at major 7
md driver 0.36.3 MAX_MD_DEV=4, MAX_REAL=8
scsi-ncr53c7xx : NCR53c710 at memory 0xfff47000, io 0x0, irq 85
scsi0: Revision 0x1
scsi0 : NCR code relocated to 0xf485e0 (virt 0x00f485e0)
scsi0 : test 1 started
scsi0 : MVME16x SCSI
scsi : 1 host.
scsi0 : target 0 accepting period 200ns offset 8 5.00MHz synchronous
SCSI
scsi0 : setting target 0 to period 200ns offset 8 5.00MHz synchronous
SCSI
Vendor: SEAGATE Model: ST11200N Rev: 9520
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
scsi0 : target 4 rejected SDTR
scsi0 : setting target 4 to asynchronous SCSI
Vendor: ARCHIVE Model: VIPER 150 21247 Rev: -011
Type: Sequential-Access ANSI SCSI revision: 01
scsi : detected 1 SCSI disk total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 2059938 [1005 MB] [1.0
GB]
eth0: Apricot 82596 at 0xfff46000, 08 00 3E 2E 4D 83 IRQ 87.
apricot.c:v0.2 05/12/94
eth0: lp at 0x0013b000, size 2920, lp->scb at 0x0013b014
Partition check:
sda: unknown partition table
RAMDISK: Compressed image found at block 0
VFS: Mounted root (minix filesystem).
# fdisk /dev/sda
/sbin/fdisk: Your system is not supported yet
#
---------------------------------------------------------
I will need the non-fpu working later, but for now the FPU version
of the board is ok.
The controller seems to work ok for status, but fdisk is unhappy about
something, I have this combinbination in another chassis and fdisk is
happy there. That cpu board is old however.
--
----------------------------------------------------------------------
John K. Stevenson, Motorola Tempe. (602) 438-3961 (FAX 602-438-6140)
JStevens@phx.mcd.mot.com Tempe. AZ
Pager: 1738917@skytel.com, 800-759-8888 pin 1738917
Reply to: