Error under OSX
Hello,
I just tried to burn a DVD under OSX:
Cdrecord-ProDVD-Clone 2.01a11 (powerpc-apple-macosx1.4) Copyright (C) 1995-2003 Jörg Schilling
Unlocked features: ProDVD Clone
Limited features:
This copy of cdrecord is licensed for: private/research/educational_non-commercial_use
TOC Type: 1 = CD-ROM
scsidev: 'IODVDServices'
devname: 'IODVDServices'
scsibus: -2 target: -2 lun: -2
Using libscg version 'schily-0.7'
cdrecord-prodvd: Warning: using inofficial libscg transport code version (csapuntz-scsi-mac-iokit.c-1.4 '@(#)scsi-mac-iokit.c 1.4 02/10/19 Copyright 1997,2001 J. Schilling').
atapi: 0
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : 'MATSHITA'
Identifikation : 'DVD-R UJ-816 '
Revision : 'DXJ3'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Profile: DVD-RW restricted overwrite
Profile: DVD-RW sequential overwrite
Profile: DVD-R sequential recording (current)
Profile: DVD-ROM
Profile: CD-RW
Profile: CD-R
Profile: CD-ROM
Profile: Removable Disk
Using generic SCSI-3/mmc-2 DVD-R/DVD-RW driver (mmc_dvd).
Driver flags : DVD MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO
Drive buf size : 1671168 = 1632 KB
FIFO size : 67108864 = 65536 KB
Track 01: data 4472 MB
Total size: 4472 MB = 2290112 sectors
Current Secsize: 2048
WARNING: Phys disk size 1 differs from rzone size 2298496! Prerecorded disk?
WARNING: Phys start: 196608 Phys end 196608
Blocks total: 2298496 Blocks current: 2298496 Blocks remaining: 8384
Starting to write CD/DVD at speed 2 in real SAO mode for single session.
Last chance to quit, starting real write 8 seconds. 0.22% done, estimate finish Wed Dec 17 21:54:04 2003
7 seconds. 0.44% done, estimate finish Wed Dec 17 21:50:15 2003
0.66% done, estimate finish Wed Dec 17 21:46:26 2003
6 seconds. 0.87% done, estimate finish Wed Dec 17 21:46:26 2003
5 seconds. 1.09% done, estimate finish Wed Dec 17 21:46:27 2003
4 seconds. 1.31% done, estimate finish Wed Dec 17 21:46:26 2003
0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
BURN-Free is ON.
Turning BURN-Free off
Starting new track at sector: 0
Track 01: 4 of 4472 MB written (fifo 100%) [buf 100%] 1.0x. 1.53% done, estimate finish Wed Dec 17 22:13:42 2003
Track 01: 14 of 4472 MB written (fifo 100%) [buf 100%] 1.0x. 1.75% done, estimate finish Wed Dec 17 22:16:58 2003
Track 01: 23 of 4472 MB written (fifo 100%) [buf 100%] 1.0x. 1.97% done, estimate finish Wed Dec 17 22:18:40 2003
...
Track 01: 4408 of 4472 MB written (fifo 100%) [buf 100%] 1.0x.100.00% done, estimate finish Wed Dec 17 22:34:50 2003
Track 01: 4409 of 4472 MB written (fifo 99%) [buf 96%] 0.9x.Total translation table size: 0
Total rockridge attributes bytes: 0
Total directory bytes: 4096
Path table size(bytes): 42
Max brk space used 0
2290112 extents written (4472 Mb)
Track 01: 4429 of 4472 MB written (fifo 100%) [buf 100%] 1.0x.cdrecord-prodvd: Error 0. write_g1: scsi sendcmd: no error
CDB: 2A 00 00 22 9B E0 00 00 10 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: F1 00 04 00 22 98 B0 0A 00 2A 00 00 03 00 00 00 00 00
Sense Key: 0x4 Hardware Error, deferred error, Segment 0
Sense Code: 0x03 Qual 0x00 (peripheral device write fault) Fru 0x0
Sense flags: Blk 2267312 (valid)
resid: 32768
cmd finished after 1.574s timeout 100s
write track data: error after 4645126144 bytes
cdrecord-prodvd: A write error occured.
cdrecord-prodvd: Please properly read the error message above.
Writing time: 3372.130s
Average write speed 1.0x.
Min drive buffer fill was 70%
Fixating...
Fixating time: 0.000s
cdrecord-prodvd: fifo had 143132 puts and 141759 gets.
cdrecord-prodvd: fifo was 0 times empty and 90979 times full, min fill was 95%.
And I don't understand the error???
Bad media?
And why is the burn only at speed 1?
Thank you very much,
Grégoire
________________________________________________________________________
http://magma.epfl.ch/greg ICQ:16624071 mailto:Gregoire.Favre@freesurf.ch
Reply to: