Buenas a tod@s, queria saber si alguien por ahi tenia configurado y funcionando el sintonizador de TDT por USB Redbell,ya que estoy teniendo algunos problemas para ponerlo a funcionar. Tengo un Pentium 3 con puertos USB 1.0 y el kernel 2.6.18-1-686 instalado. He seguido todos los pasos que explican aqui: He copiado el firmware que indican en la web en su carpeta correspondiente /lib/firmware/ He utilizado el 2 porque es el firmware con el que se me enciende el LED del dispositivo USB. La salida que me da el /var/log/messages cuando conecto el REDBELL es la siguiente: Oct 8 16:04:22 jatabe kernel: usb 1-2: new full speed USB device using uhci_hcd and address 4 Oct 8 16:04:22 jatabe kernel: usb 1-2: configuration #1 chosen from 1 choice Oct 8 16:04:22 jatabe kernel: dvb-usb: found a 'WideView WT-220U PenType Receiver (based on ZL353)' in cold state, will try to load a firmware Oct 8 16:04:22 jatabe kernel: dvb-usb: downloading firmware from file 'dvb-usb-wt220u-zl0353-01.fw' Oct 8 16:04:24 jatabe kernel: usb 1-2: USB disconnect, address 4 Oct 8 16:04:24 jatabe kernel: dvb-usb: generic DVB-USB module successfully deinitialized and disconnected. Oct 8 16:04:25 jatabe kernel: usb 1-2: new full speed USB device using uhci_hcd and address 5 Oct 8 16:04:25 jatabe kernel: usb 1-2: configuration #1 chosen from 1 choice Oct 8 16:04:25 jatabe kernel: dvb-usb: found a 'WideView WT-220U PenType Receiver (based on ZL353)' in warm state. Oct 8 16:04:25 jatabe kernel: dvb-usb: will use the device's hardware PID filter (table count: 15). Oct 8 16:04:25 jatabe kernel: DVB: registering new adapter (WideView WT-220U PenType Receiver (based on ZL353)). Oct 8 16:04:25 jatabe kernel: DVB: registering frontend 0 (WideView USB DVB-T)... Oct 8 16:04:25 jatabe kernel: input: IR-receiver inside an USB DVB receiver as /class/input/input4 Oct 8 16:04:25 jatabe kernel: dvb-usb: schedule remote query interval to 300 msecs. Oct 8 16:04:25 jatabe kernel: dvb-usb: WideView WT-220U PenType Receiver (based on ZL353) successfully initialized and connected. En principio todo parece correcto. Seguido he instalado el paquete dvb-utils y he intentado escanear para ver si me localizaba algun canal,pero esto es lo que obtengo : jatabe:~# scan /usr/share/doc/dvb-utils/examples/scan/dvb-t/es-Madrid scanning /usr/share/doc/dvb-utils/examples/scan/dvb-t/es-Madrid using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' initial transponder 770000000 0 2 1 3 1 3 0 initial transponder 810000000 0 2 1 3 1 3 0 initial transponder 834000000 0 2 1 3 1 3 0 initial transponder 842000000 0 2 1 3 1 3 0 initial transponder 850000000 0 2 1 3 1 3 0 initial transponder 858000000 0 2 1 3 1 3 0 >>> tune to: 770000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_1_2:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_4:HIERARCHY_NONE WARNING: >>> tuning failed!!! >>> tune to: 770000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_1_2:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_4:HIERARCHY_NONE (tuning failed) WARNING: >>> tuning failed!!! >>> tune to: 810000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_1_2:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_4:HIERARCHY_NONE WARNING: filter timeout pid 0x0011 WARNING: filter timeout pid 0x0000 WARNING: filter timeout pid 0x0010 >>> tune to: 834000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_1_2:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_4:HIERARCHY_NONE WARNING: filter timeout pid 0x0011 WARNING: filter timeout pid 0x0000 WARNING: filter timeout pid 0x0010 >>> tune to: 842000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_1_2:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_4:HIERARCHY_NONE WARNING: filter timeout pid 0x0011 WARNING: filter timeout pid 0x0000 WARNING: filter timeout pid 0x0010 >>> tune to: 850000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_1_2:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_4:HIERARCHY_NONE WARNING: filter timeout pid 0x0011 WARNING: filter timeout pid 0x0000 WARNING: filter timeout pid 0x0010 >>> tune to: 858000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_1_2:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_4:HIERARCHY_NONE WARNING: filter timeout pid 0x0011 WARNING: filter timeout pid 0x0000 WARNING: filter timeout pid 0x0010 dumping lists (0 services) Done. Y al obtener este resultado si hago un dmesg veo lo siguiente: ----Esto cuando conecto el usb---- dvb-usb: WideView WT-220U PenType Receiver (based on ZL353) successfully deinitialized and disconnected. usb 1-2: new full speed USB device using uhci_hcd and address 4 usb 1-2: configuration #1 chosen from 1 choice dvb-usb: found a 'WideView WT-220U PenType Receiver (based on ZL353)' in cold state, will try to load a firmware dvb-usb: downloading firmware from file 'dvb-usb-wt220u-zl0353-01.fw' usb 1-2: USB disconnect, address 4 dvb-usb: generic DVB-USB module successfully deinitialized and disconnected. usb 1-2: new full speed USB device using uhci_hcd and address 5 usb 1-2: configuration #1 chosen from 1 choice dvb-usb: found a 'WideView WT-220U PenType Receiver (based on ZL353)' in warm state. dvb-usb: will use the device's hardware PID filter (table count: 15). DVB: registering new adapter (WideView WT-220U PenType Receiver (based on ZL353)). DVB: registering frontend 0 (WideView USB DVB-T)... input: IR-receiver inside an USB DVB receiver as /class/input/input4 dvb-usb: schedule remote query interval to 300 msecs. dvb-usb: WideView WT-220U PenType Receiver (based on ZL353) successfully initialized and connected. ----Esto cuando realizo el escaneo---- dvb-usb: recv bulk message failed: -110 dvb-usb: could not submit URB no. 0 - get them all back dvb-usb: could not submit URB no. 0 - get them all back dvb-usb: could not submit URB no. 0 - get them all back dvb-usb: could not submit URB no. 0 - get them all back dvb-usb: could not submit URB no. 0 - get them all back dvb-usb: could not submit URB no. 0 - get them all back Cuando esta escaneando ... la luz del led del USB parece que se apaga y al de un rato se vuelve a encender. Alguien sabria decirme por donde puede venir el problema ? O alguien mas ha tenido por ahi el mismo problema ? Gracias y salu2. PD: Añadir que el mismo dispositivo USB en el mismo equipo pero con WinXP funciona correctamente. ========================= Jon Ander Bilbao Ortiz Linux Registered User# 395404 ========================= |
Attachment:
PGP.sig
Description: Mensaje firmado digitalmente