Re: [OT] 2 ethernets
2 defaults gw? Con uno basta... Pero no se si eso es el "causante"
del problema...
A Divendres 21 Setembre 2001 18:09, Alexis Roda va escriure:
> Hola a todos,
> estoy intentado configurar una maquina (potato con nucleo 2.2.19) con
> dos ethernets y no hay manera de que funcione. A ver si alguien de la
> lista puede echarme una mano.
>
> eth0 es un 3Com 509 y eth1 una DLink 220, ambas son detectadas por el
> nucleo y se encuentran en redes diferentes (10.40.0.0/16 y
> 10.20.0.0/16). Lo curioso es que si hago pings a ambas IPs solamente
> responde la eth0. Si bajo (ifdown) eth0 entonces eth1 si responde, pero
> cuando vuelvo a subir eth0 deja de responder. Por si sirve de algo aqui
> teneis la tabla de enrutamiento i la salida de ifconfig:
>
> logger:~# cat /etc/network/interfaces
> # /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)
>
> # The loopback interface
> iface lo inet loopback
>
> iface eth0 inet static
> address 10.40.200.152
> netmask 255.255.0.0
> network 10.40.0.0
> broadcast 10.40.255.255
> gateway 10.40.0.1
>
> iface eth1 inet static
> address 10.20.200.12
> netmask 255.255.0.0
> network 10.20.0.0
> broadcast 10.20.255.255
> gateway 10.20.0.1
>
> logger:~# ifconfig
> eth0 Link encap:Ethernet HWaddr 00:A0:24:EB:68:3B
> inet addr:10.40.200.152 Bcast:10.40.255.255 Mask:255.255.0.0
> UP BROADCAST RUNNING MTU:1500 Metric:1
> RX packets:14167 errors:0 dropped:0 overruns:0 frame:0
> TX packets:594 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:100
> Interrupt:5 Base address:0x200
>
> eth1 Link encap:Ethernet HWaddr 00:80:C8:3A:03:43
> inet addr:10.20.200.12 Bcast:10.20.255.255 Mask:255.255.0.0
> UP BROADCAST RUNNING MTU:1500 Metric:1
> RX packets:840 errors:0 dropped:0 overruns:0 frame:0
> TX packets:41 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:100
> Interrupt:10 Base address:0x300
>
> logger:~# route -n
> Kernel IP routing table
> Destination Gateway Genmask Flags Metric Ref Use
> Iface
> 10.20.0.0 0.0.0.0 255.255.0.0 U 0 0 0
> eth1
> 10.40.0.0 0.0.0.0 255.255.0.0 U 0 0 0
> eth0
> 0.0.0.0 10.40.0.1 0.0.0.0 UG 0 0 0
> eth0
> 0.0.0.0 10.20.0.1 0.0.0.0 UG 0 0 0
> eth1
>
>
> Saludos y gracias por adelantado
--
Jaume Sabater - Dep. Sistemes - ARGUS Serveis Telemàtics
Per escriure aquest mail no s'han maltractat animals ni s'han usat productes
MicroSoft.
Reply to: