Re: CD Brenn-Problem
Am Mittwoch 03 September 2008 13:37:10 schrieb Klaus Becker:
> Moin,
>
> ich benutze Lenny auf AMD64.
>
> Eine CDRW kann ich mit k3b brennen, aber bei 2 verschiedenen CDR-Marken
> bricht er ab mit der Meldung : "Wahrscheinlich unterstützt der Brenner das
> Medium nicht."
>
> Das glaube ich aber nicht, denn unter Etch hatte ich dieses Problem mit den
> gleichen CDRs nicht.
>
> Liegt das an Lenny, fehlt da noch ein Paket oder ist da ein Paket noch
> etwas grün ? Oder hat jemand eine andere Idee ?
>
> tschüs
>
> Klaus
ich hatte vergessen, die Fehlerausgabe mitzuschicken :
System
-----------------------
K3b Version: 1.0.5
KDE Version: 3.5.9
QT Version: 3.3.8b
Kernel: 2.6.25-2-amd64
Devices
-----------------------
_NEC DVD_RW ND-3500AG 2.16 (/dev/hdc, ) [CD-R, CD-RW, CD-ROM, DVD-ROM, DVD-R,
DVD-RW, DVD+R, DVD+RW, DVD+R doppelschichtig] [DVD-ROM, DVD-R Sequentiell,
DVD-RW Eingeschränktes Überbrennen, DVD-RW Sequentiell, DVD+RW, DVD+R,
Zweischichtige DVD+R, CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96R,
RAW/R96R, Eingeschränktes Überschreiben]
Used versions
-----------------------
cdrecord: 1.1.8
cdrecord
-----------------------
/usr/bin/wodim: Operation not permitted. Warning: Cannot raise RLIMIT_MEMLOCK
limits.scsidev: '/dev/hdc'
devname: '/dev/hdc'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.8
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 1 = CD-ROM
Driveropts: 'burnfree'
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : '_NEC '
Identification : 'DVD_RW ND-3500AG'
Revision : '2.16'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x0009 (CD-R)
Profile: 0x002B (DVD+R/DL)
Profile: 0x001B (DVD+R)
Profile: 0x001A (DVD+RW)
Profile: 0x0014 (DVD-RW sequential recording)
Profile: 0x0013 (DVD-RW restricted overwrite)
Profile: 0x0011 (DVD-R sequential recording)
Profile: 0x0010 (DVD-ROM)
Profile: 0x000A (CD-RW)
Profile: 0x0009 (CD-R) (current)
Profile: 0x0008 (CD-ROM) (current)
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96R RAW/R96R
Drive buf size : 1343488 = 1312 KB
FIFO size : 12582912 = 12288 KB
Speed set to 2822 KB/s
Track 01: data 696 MB
Total size: 799 MB (79:12.90) = 356468 sectors
Lout start: 799 MB (79:14/68) = 356468 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 5
Is not unrestricted
Is not erasable
Disk sub type: Medium Type B, low Beta category (B-) (4)
ATIP start of lead in: -12421 (97:16/29)
ATIP start of lead out: 359848 (79:59/73)
Disk type: Short strategy type (Phthalocyanine or similar)
Manuf. index: 71
Manufacturer: SHENZEN SG&GAST DIGITAL OPTICAL DISCS
Manufacturer is guessed because of the orange forum embargo.
The orange forum likes to get money for recent information.
The information for this media may not be correct.
Blocks total: 359848 Blocks current: 359848 Blocks remaining: 3380
Starting to write CD/DVD at speed 16.0 in real SAO mode for single session.
Last chance to quit, starting real write in 2 seconds.
1 seconds.
0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Errno: 0 (Success), send opc scsi sendcmd: no error
CDB: 54 01 00 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 03 00 00 00 00 0A 00 00 00 00 73 03 00 00
Sense Key: 0x3 Medium Error, Segment 0
Sense Code: 0x73 Qual 0x03 (power calibration area error) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 6.032s timeout 200s
/usr/bin/wodim: OPC failed.
Writing time: 8.966s
BURN-Free was never needed.
/usr/bin/wodim: fifo had 191 puts and 0 gets.
/usr/bin/wodim: fifo was 0 times empty and 0 times full, min fill was 100%.
cdrecord command:
-----------------------
/usr/bin/wodim -v gracetime=2 dev=/dev/hdc speed=16 -dao
driveropts=burnfree -eject -data -tsize=356468s -
Klaus
Reply to: