Comment configurer une carte WiFi NetGear WG311
Bonsoir,
Après moultes recherches je m'en retourne à ma liste debian adorée.
Ma question est la suivante :
Comment faire fonctionner une carte WirelessFidelity :
NetGear WG311 54Mb/s sur ma debian woody. Noyau 2.4.24
J'ai essayé 2 drivers :
le prism54 et le madwifi
voici le resultat du mawifiwiki :
Avant quelques info sur ma carte pci :
-----------------------------------------------
00:0f.0 Ethernet controller: Unknown device 168c:0013 (rev 01)
Bus 0, device 15, function 0:
Ethernet controller: PCI device 168c:0013 (rev 1).
IRQ 10.
Master Capable. Latency=64. Min Gnt=10.Max Lat=28.
Non-prefetchable 32 bit memory at 0xcffe0000 [0xcffeffff].
-----------------------------------------------
# ifconfig ath0
-----------------------------------------------
ath0 Lien encap:Ethernet HWaddr 00:09:5B:98:0A:68
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:199
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interruption:7 Mémoire:e1c4b000-e1c5b000
-----------------------------------------------
# iwconfig ath0
-----------------------------------------------
ath0 IEEE 802.11 ESSID:""
Mode:Managed Frequency:2.412GHz Access Point: 00:00:00:00:00:00
Bit Rate:0kb/s Tx-Power:off Sensitivity=0/0
Retry:off RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
-----------------------------------------------
# iwconfig ath0 mode ad-hoc channel 10 rate 54M auto essid mon_reseau nick
server
-----------------------------------------------
Error for wireless request "Set Mode" (8B06) :
SET failed on device ath0 ; No such device or address.
-----------------------------------------------
si je fais :
# iwconfig ath0 mode managed channel 10 rate 54M auto essid mon_reseau nick
server
Ca passe.
Il semblerait qu'il n'accepte pas le mode Ad-hoc (network composed of only one
cell and without Access Point)
Ensuite :
Si j'adresse les cartes wifi et que je ping :
# ifconfig ath0 inet 192.168.0.101 up
# ping -c 192.168.0.101
-----------------------------------------------
PING 192.168.0.101 (192.168.0.101): 56 data bytes
--- 192.168.0.101 ping statistics ---
3 packets transmitted, 0 packets received, 100% packet loss
-----------------------------------------------
# ifconfig ath0 (sur l'autre machine)
-----------------------------------------------
ath0 Lien encap:Ethernet HWaddr 00:09:5B:98:0A:87
inet adr:192.168.0.102 Bcast:192.168.0.255 Masque:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:42 errors:78880 dropped:0 overruns:0 frame:0
TX packets:122 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:199
RX bytes:2352 (2.2 KiB) TX bytes:6822 (6.6 KiB)
Interruption:10 Mémoire:c8a30000-c8a40000
-----------------------------------------------
On voit errors:78880!!!
Après un véritable roman...
Quelqu'un a une idée????
Merci,
Jérémy Lévy
----------------------------------------------------------------
This message was sent using IMP, the Internet Messaging Program.
Reply to: