Re: radeonfb: only 80x25
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Benjamin Herrenschmidt wrote:
| Not sure,can you enable radeonfb verbose debug and send me the output of
| dmesg ?
Done. Here is the dmesg
by, Martin
- --
Powered by Debian GNU / Linux
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.5 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://enigmail.mozdev.org
iD8DBQFCEyfWGxxhbGlQyAkRAqH2AJ94ION2RmKA+S1DRr9nERCFr57QdwCdET+Z
ctInLfYWG2SrZioA0k2P2Wk=
=kavx
-----END PGP SIGNATURE-----
Total memory = 384MB; using 1024kB for hash table (at c0400000)
Linux version 2.6.11-rc4 (root@ibook) (gcc version 3.3.5 (Debian 1:3.3.5-8)) #1 Wed Feb 16 11:22:36 CET 2005
Found UniNorth memory controller & host bridge, revision: 210
Mapped at 0xfdfc0000
Found a Intrepid mac-io controller, rev: 0, mapped at 0xfdf40000
Processor NAP mode on idle enabled.
PowerMac motherboard: iBook G4
Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->0
Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->0
Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->0
via-pmu: Server Mode is disabled
PMU driver 2 initialized for Core99, firmware: 0c
nvram: Checking bank 0...
nvram: gen0=334, gen1=333
nvram: Active bank is: 0
nvram: OF partition at 0x410
nvram: XP partition at 0x1020
nvram: NR partition at 0x1120
On node 0 totalpages: 98304
DMA zone: 98304 pages, LIFO batch:16
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=/dev/hda6 ro ethernet=offline video=radeonfb:1024x786-32
PowerMac using OpenPIC irq controller at 0x80040000
OpenPIC Version 1.2 (4 CPUs and 64 IRQ sources) at fc6ef000
OpenPIC timer frequency is 4.166666 MHz
PID hash table entries: 2048 (order: 11, 32768 bytes)
GMT Delta read from XPRAM: 0 minutes, DST: off
time_init: decrementer frequency = 18.432000 MHz
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 384384k available (2544k kernel code, 1220k data, 168k init, 0k highmem)
AGP special page: 0xd7fff000
Calibrating delay loop... 610.30 BogoMIPS (lpj=305152)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
NET: Registered protocol family 16
PCI: Probing PCI hardware
PCI: Cannot allocate resource region 0 of device 0001:10:18.0
PCI: Cannot allocate resource region 0 of device 0001:10:19.0
Apple USB OHCI 0001:10:18.0 disabled by firmware
Apple USB OHCI 0001:10:19.0 disabled by firmware
Registering openpic with sysfs...
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Thermal assist unit not available
Registering PowerMac CPU frequency driver
Low: 606 Mhz, High: 798 Mhz, Boot: 606 Mhz
SGI XFS with no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
radeonfb_pci_register BEGIN
PCI: Enabling device 0000:00:10.0 (0006 -> 0007)
aper_base: 98000000 MC_FB_LOC to: 9bff9800, MC_AGP_LOC to: ffffa000
radeonfb (0000:00:10.0): Found 32768k of DDR 64 bits wide videoram
radeonfb (0000:00:10.0): mapped 16384k videoram
radeonfb (0000:00:10.0): Invalid ROM signature 0 should be0xaa55
radeonfb: Retreived PLL infos from Open Firmware
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=190.00 Mhz, System=183.00 MHz
radeonfb: PLL min 12000 max 35000
Starting monitor auto detection...
radeonfb: I2C (port 1) ... not found
radeonfb: I2C (port 2) ... found LVDS panel
radeonfb: I2C (port 3) ... not found
radeonfb: I2C (port 4) ... not found
radeon_probe_OF_head
head: ATY,Via_A (letter: A, head_no: 0)
analyzing OF properties...
display-type: LCD
radeon_probe_OF_head
head: ATY,Via_A (letter: A, head_no: 1)
radeonfb: I2C (port 3) ... not found
radeonfb: I2C (port 4) ... not found
radeonfb: Monitor 1 type LCD found
radeonfb: EDID probed
radeonfb: Monitor 2 type no found
Parsing EDID data for panel info
radeonfb: Using Firmware dividers 0x000600ad from PPLL 0
Setting up default mode based on panel info
radeonfb: Dynamic Clock Power Management enabled
hStart = 664, hEnd = 800, hTotal = 960
vStart = 403, vEnd = 409, vTotal = 438
h_total_disp = 0x4f0077 hsync_strt_wid = 0x910292
v_total_disp = 0x18f01b5 vsync_strt_wid = 0x860192
pixclock = 15384
freq = 6500
Console: switching to colour frame buffer device 80x25
Registered "mnca" backlight controller, level: 15/15
radeonfb (0000:00:10.0): ATI Radeon \c
radeonfb_pci_register END
Macintosh non-volatile memory driver v1.1
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected Apple UniNorth 2 chipset
agpgart: Maximum main memory to use for agp memory: 322M
agpgart: configuring for size idx: 4
agpgart: AGP aperture is 16M @ 0x0
[drm] Initialized drm 1.0.0 20040925
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
sungem.c:v0.98 8/24/03 David S. Miller (davem@redhat.com)
eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:0a:95:ac:20:be
PHY ID: 4061e4, addr: 0
eth0: Found BCM5221 PHY
MacIO PCI driver attached to Intrepid chipset
input: Macintosh mouse button emulation
apm_emu: APM Emulation 0.5 initialized.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
adb: starting probe task...
PCI: Enabling device 0002:20:0d.0 (0000 -> 0002)
adb devices: [2]: 2 c4 [3]: 3 1 [7]: 7 1f
ADB keyboard at 2, handler 1
Detected ADB keyboard, type ISO, swapping keys.
input: ADB keyboard on adb2:2.c4/input
input: ADB Powerbook buttons on adb7:7.1f/input
ADB mouse at 3, handler set to 4 (trackpad)
input: ADB mouse on adb3:3.01/input
adb: finished probe task...
ide0: Found Apple UniNorth ATA-6 controller, bus ID 3, irq 39
Probing IDE interface ide0...
hda: TOSHIBA MK3021GAS, ATA DISK drive
hda: Enabling Ultra DMA 5
ide0 at 0xd9022000-0xd9022007,0xd9022160 on irq 39
ide1: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 24
Probing IDE interface ide1...
hdc: MATSHITACD-RW CW-8123, ATAPI CD/DVD-ROM drive
hdc: Enabling MultiWord DMA 2
ide1 at 0xd900e000-0xd900e007,0xd900e160 on irq 24
hda: max request size: 128KiB
hda: 58605120 sectors (30005 MB), CHS=58140/16/63, UDMA(100)
hda: cache flushes supported
hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, (U)DMA
Uniform CD-ROM driver Revision: 3.20
mice: PS/2 mouse device common for all mice
Found KeyWest i2c on "uni-n", 2 channels, stepping: 4 bits
Found KeyWest i2c on "mac-io", 1 channel, stepping: 4 bits
tas driver [TAS3004 driver V 0.3])
using i2c address: 0x35 from device-tree
Audio jack unplugged, enabling speakers.
AE-Init snapper mixer
PowerMac Snapper DMA sound driver rev 016 installed
Core driver edition 01.06 : PowerMac Built-in Sound driver edition 00.07
Write will use 4 fragments of 32768 bytes as default
Read will use 4 fragments of 32768 bytes as default
Advanced Linux Sound Architecture Driver Version 1.0.8 (Thu Jan 13 09:39:32 2005 UTC).
pmac: can't request resource 0!
ALSA device list:
No soundcards found.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
NET: Registered protocol family 1
NET: Registered protocol family 17
XFS mounting filesystem hda6
Ending clean XFS mount for filesystem: hda6
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 168k init 4k chrp 32k prep
Adding 438692k swap on /var/swap/swapfile. Priority:-1 extents:2
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
PCI: Enabling device 0002:20:0e.0 (0000 -> 0002)
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[40] MMIO=[f5000000-f50007ff] Max Packet=[2048]
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Apple USB OHCI 0001:10:18.0 disabled by firmware
Apple USB OHCI 0001:10:19.0 disabled by firmware
PCI: Enabling device 0001:10:1a.0 (0000 -> 0002)
ohci_hcd 0001:10:1a.0: Apple Computer Inc. KeyLargo/Intrepid USB (#3)
ohci_hcd 0001:10:1a.0: irq 29, pci mem 0x80083000
ohci_hcd 0001:10:1a.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Enabling device 0001:10:1b.0 (0000 -> 0002)
ohci_hcd 0001:10:1b.0: NEC Corporation USB
ohci_hcd 0001:10:1b.0: irq 63, pci mem 0x80082000
ohci_hcd 0001:10:1b.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
PCI: Enabling device 0001:10:1b.1 (0000 -> 0002)
ohci_hcd 0001:10:1b.1: NEC Corporation USB (#2)
ohci_hcd 0001:10:1b.1: irq 63, pci mem 0x80081000
ohci_hcd 0001:10:1b.1: new USB bus registered, assigned bus number 3
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000a95fffeac20be]
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
PCI: Enabling device 0001:10:1b.2 (0004 -> 0006)
ehci_hcd 0001:10:1b.2: NEC Corporation USB 2.0
ehci_hcd 0001:10:1b.2: irq 63, pci mem 0x80080000
ehci_hcd 0001:10:1b.2: new USB bus registered, assigned bus number 4
ehci_hcd 0001:10:1b.2: park 0
ehci_hcd 0001:10:1b.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 5 ports detected
hStart = 1048, hEnd = 1184, hTotal = 1344
vStart = 771, vEnd = 777, vTotal = 806
h_total_disp = 0x7f00a7 hsync_strt_wid = 0x910415
v_total_disp = 0x2ff0325 vsync_strt_wid = 0x860302
pixclock = 15384
freq = 6500
[drm] Initialized radeon 1.14.0 20050125 on minor 0: ATI Technologies Inc RV250 5c63 [Radeon Mobility 9200 M9+]
agpgart: Putting AGP V2 device at 0000:00:0b.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:00:10.0 into 4x mode
[drm] Loading R200 Microcode
usb 2-1: new full speed USB device using ohci_hcd and address 2
prism2usb_init: prism2_usb.o: 0.2.1-pre26 Loaded
prism2usb_init: dev_info is: prism2_usb
usbcore: registered new driver prism2_usb
Writing 4096 bytes to ram @0x7e2ffe
Writing 4096 bytes to ram @0x7e3ffe
Writing 4096 bytes to ram @0x7e4ffe
Writing 4096 bytes to ram @0x7e5ffe
Writing 4096 bytes to ram @0x7e6ffe
Writing 4096 bytes to ram @0x7e7ffe
Writing 4096 bytes to ram @0x7e8ffe
Writing 4096 bytes to ram @0x7e9ffe
Writing 4096 bytes to ram @0x7eaffe
Writing 4096 bytes to ram @0x7ebffe
Writing 4096 bytes to ram @0x7ecffe
Writing 4096 bytes to ram @0x7edffe
Writing 3010 bytes to ram @0x7eeffe
Writing 416 bytes to ram @0x7efc20
Writing 16 bytes to ram @0x7efdd0
Writing 4044 bytes to ram @0x7f0800
Writing 3288 bytes to ram @0x7fe000
ident: nic h/w: id=0x8026 1.0.0
ident: pri f/w: id=0x15 1.1.3
ident: sta f/w: id=0x1f 1.8.3
MFI:SUP:role=0x00:id=0x01:var=0x01:b/t=1/1
CFI:SUP:role=0x00:id=0x02:var=0x02:b/t=1/1
PRI:SUP:role=0x00:id=0x03:var=0x01:b/t=1/4
STA:SUP:role=0x00:id=0x04:var=0x01:b/t=1/15
PRI-CFI:ACT:role=0x01:id=0x02:var=0x02:b/t=1/1
STA-CFI:ACT:role=0x01:id=0x02:var=0x02:b/t=1/1
STA-MFI:ACT:role=0x01:id=0x01:var=0x01:b/t=1/1
Prism2 card SN: 000000000000
linkstatus=CONNECTED
hStart = 664, hEnd = 800, hTotal = 960
vStart = 403, vEnd = 409, vTotal = 438
h_total_disp = 0x4f0077 hsync_strt_wid = 0x910292
v_total_disp = 0x18f01b5 vsync_strt_wid = 0x860192
pixclock = 15384
freq = 6500
hStart = 1048, hEnd = 1184, hTotal = 1344
vStart = 771, vEnd = 777, vTotal = 806
h_total_disp = 0x7f00a7 hsync_strt_wid = 0x910415
v_total_disp = 0x2ff0325 vsync_strt_wid = 0x860302
pixclock = 15384
freq = 6500
agpgart: Putting AGP V2 device at 0000:00:0b.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:00:10.0 into 4x mode
[drm] Loading R200 Microcode
hStart = 664, hEnd = 800, hTotal = 960
vStart = 403, vEnd = 409, vTotal = 438
h_total_disp = 0x4f0077 hsync_strt_wid = 0x910292
v_total_disp = 0x18f01b5 vsync_strt_wid = 0x860192
pixclock = 15384
freq = 6500
hStart = 664, hEnd = 800, hTotal = 960
vStart = 403, vEnd = 409, vTotal = 438
h_total_disp = 0x4f0077 hsync_strt_wid = 0x910292
v_total_disp = 0x18f01b5 vsync_strt_wid = 0x860192
pixclock = 15384
freq = 6500
hStart = 1048, hEnd = 1184, hTotal = 1344
vStart = 771, vEnd = 777, vTotal = 806
h_total_disp = 0x7f00a7 hsync_strt_wid = 0x910415
v_total_disp = 0x2ff0325 vsync_strt_wid = 0x860302
pixclock = 15384
freq = 6500
agpgart: Putting AGP V2 device at 0000:00:0b.0 into 2x mode
agpgart: Putting AGP V2 device at 0000:00:10.0 into 2x mode
[drm] Loading R200 Microcode
Reply to: