Re: Problems with IDE master/slave settings on Blue & White
Op 15-aug-04 om 09:44 heeft Geert Uytterhoeven het volgende geschreven:
disk: CS + Master
cdrom: CS + Slave
So either you jumper for cable select, or for master/slave. You better
don't
combine them.
So, do I put:
disk: CS
cdrom: CS
or
disk: CS
cdrom:
(alternate is CS on cdrom)
When I do the latest on the G3/266 I get in dmesg:
(I cannot boot from the second HD(macos + linux), that is linked with
the
cdrom to ide1)
hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hda: task_no_data_intr: error=0x04 { DriveStatusError }
Marc:
As PS: complete dmesg on G3/266
Memory BAT mapping: BAT2=128Mb, BAT3=32Mb, residual: 64Mb
Total memory = 160MB; using 512kB for hash table (at c0380000)
Linux version 2.4.22-2f (dburcaw@skyfox.terraplex.com) (gcc version
3.2.2 20030217 (Yellow Dog Linux 3.0 3.2.2-2a)) #1 Sun Nov 9 16:49:49
EST 2003
Found a Heathrow mac-io controller, rev: 1, mapped at 0xfdee9000
PowerMac motherboard: PowerMac G3 (Silk)
CPU HID1 : 0xa0000000
Found Grackle (MPC106) PCI host bridge at 0x80000000. Firmware bus
number: 0->0
hose pci, pci_mem_offset: 00000000, start0: 80000000
io_base_virt: fd6e6000, io_base_phys: fe000000, isa_mem_base: fd000000
nvram: OF partition at 0x1800
nvram: XP partition at 0x1300
nvram: NR partition at 0x1400
On node 0 totalpages: 40960
zone(0): 40960 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/hdc10
System has 64 possible interrupts
GMT Delta read from XPRAM: 120 minutes, DST: on
via_calibrate_decr: ticks per jiffy = 167085 (1002512 ticks)
Console: colour dummy device 80x25
Calibrating delay loop... 534.11 BogoMIPS
Memory: 157656k available (2228k kernel code, 1148k data, 176k init, 0k
highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Scanning bus 00
Found 00:00 [1057/0002] 000600 00
Found 00:80 [106b/0010] 00ff00 00
Found 00:90 [1002/4750] 000300 00
PCI:00:12.0 Resource 6 [00000000-0001ffff] is unassigned
Fixups for bus 00
Bus scan for 00 returning with max=00
PCI: bridge rsrc 0..7fffff (100), parent c0287194
PCI: bridge rsrc 80000000..fcffffff (200), parent c02871b0
PCI: bridge rsrc fd000000..fdffffff (200), parent c02871b0
PCI:00:10.0: Resource 0: f3000000-f307ffff (f=200), vd: 106b, dev: 0010
PCI:00:12.0: Resource 0: 81000000-81ffffff (f=200), vd: 1002, dev: 4750
PCI:00:12.0: Resource 2: 80800000-80800fff (f=200), vd: 1002, dev: 4750
PCI:00:12.0: Resource 1: 00000c00-00000cff (f=101), vd: 1002, dev: 4750
Macintosh CUDA driver v0.5 for Unified ADB.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Thermal assist unit using timers, shrink_timer: 200 jiffies
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
udf: registering filesystem
atyfb: using auxiliary register aperture
atyfb: 3D RAGE PRO (PQFP, PCI) [0x4750 rev 0x7c] 2M SGRAM, 14.31818 MHz
XTAL, 230 MHz PLL, 100 Mhz MCLK
atyfb: monitor sense=73f, mode 6
Console: switching to colour frame buffer device 80x30
fb0: ATY Mach64 frame buffer device on PCI
MacOS display is /pci/ATY,mach64_3DUPro
input0: Macintosh mouse button emulation
pty: 256 Unix98 ptys configured
fd0: SWIM3 floppy controller
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
eth0: BMAC at 00:05:02:d3:7e:db
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
ide0: Found Apple Heathrow ATA controller, bus ID 0
ide1: Found Apple Heathrow ATA controller, bus ID 1
Probing IDE interface ide0...
hda: QUANTUM FIREBALL SE4.3A, ATA DISK drive
Unhandled interrupt d, disabled
hda: Enabling MultiWord DMA 2
Probing IDE interface ide1...
hdc: Maxtor 6E040L0, ATA DISK drive
hdd: MATSHITA CR-587, ATAPI CD/DVD-ROM drive
Unhandled interrupt e, disabled
hdc: Enabling MultiWord DMA 2
hdd: Enabling MultiWord DMA 2
ide0 at 0xcb85b000-0xcb85b007,0xcb85b160 on irq 13
ide1 at 0xcb85f000-0xcb85f007,0xcb85f160 on irq 14
hda: attached ide-disk driver.
hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hda: task_no_data_intr: error=0x04 { DriveStatusError }
hda: 8418816 sectors (4310 MB) w/80KiB Cache, CHS=14848/9/63, (U)DMA
hdc: attached ide-disk driver.
hdc: host protected area => 1
hdc: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=79656/16/63,
(U)DMA
hdd: attached ide-cdrom driver.
hdd: ATAPI 24X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7
hdc: [mac] hdc1 hdc2 hdc3 hdc4 hdc5 hdc6 hdc7 hdc8 hdc9 hdc10
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
mesh: configured for synchronous 5 MB/s
mesh: performing initial bus reset...
scsi1 : MESH
PowerMac Z8530 serial driver version 2.0
tty00 at 0xcb867020 (irq = 15) is a Z8530 ESCC, port = modem
tty01 at 0xcb86a000 (irq = 16) is a Z8530 ESCC, port = printer
Macintosh non-volatile memory driver v1.0
apm_emu: Requires a machine with a PMU.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
adb: starting probe task...
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 176k init 8k chrp 8k prep
adb devices: [2]: 2 5 [3]: 3 1
ADB keyboard at 2, handler set to 3
Detected ADB keyboard, type ISO, swapping keys.
input1: ADB HID on ID 2:2.05
ADB mouse at 3, handler set to 2
input2: ADB HID on ID 3:3.01
adb: finished probe task...
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide1(22,10), internal journal
Adding Swap: 393208k swap-space (priority -1)
ip_tables: (C) 2000-2002 Netfilter core team
phy registers:
0000 0000 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
NET4: AppleTalk 0.18a for Linux NET4.0
i2c-core.o: i2c core module
dmasound_pmac: Awacs/Screamer Codec Mfct: 2 Rev 3
PowerMac Screamer DMA sound driver rev 016 installed
Core driver edition 01.06 : PowerMac Built-in Sound driver edition 00.07
Write will use 4 fragments of 32768 bytes as default
Read will use 4 fragments of 32768 bytes as default
Marc
Reply to: