Pahin. The purpose of a list like this is for others to benefit from
experiences/fixes and the like. Omitting the list after finding a
helpful hand is counter productive. Please address the list when
replying to help.
Excerpts from pahnin sd's message of Thu Mar 17 10:35:45 -0400 2011:
[...]> On Thu, Mar 17, 2011 at 7:59 PM, Philippe LeCavalier <
> email@example.com> wrote:
> > Excerpts from pahnin sd's message of Thu Mar 17 10:23:37 -0400 2011:
> > > I am using debian 6.0
> > > My wifi is working fine but I couldn't use lan on my laptop..
> > > It shows in gnome panel that, wired networks is not managed .. I have
> > > searched on internet but I could nt find gud solution.
> > > Please help me...
> > What do lspci and ifconfig show? dmesg | grep eth could also help us
> > help you.
> > --
> when I connectd lan wire dmesg | grep eth
> [ 1.850489] sky2 eth0: addr 00:24:be:b8:13:7c
> [ 15.630845] sky2 eth0: enabling interface
> [ 15.631279] ADDRCONF(NETDEV_UP): eth0: link is not ready
> [ 101.670659] sky2 eth0: disabling interface
> [ 102.931253] sky2 eth0: enabling interface
> [ 102.931707] ADDRCONF(NETDEV_UP): eth0: link is not ready
> [ 9597.445540] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control
> [ 9597.445976] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> [ 9607.681270] eth0: no IPv6 routers present
> eth0 Link encap:Ethernet HWaddr 00:24:be:b8:13:7c
> inet addr:192.168.212.53 Bcast:192.168.215.255
> inet6 addr: fe80::224:beff:feb8:137c/64 Scope:Link
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:2333 errors:0 dropped:0 overruns:0 frame:0
> TX packets:86 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:184831 (180.4 KiB) TX bytes:9817 (9.5 KiB)
> wlan0 Link encap:Ethernet HWaddr 2c:81:58:eb:95:45[...]
> inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0
> inet6 addr: fe80::2e81:58ff:feeb:9545/64 Scope:Link
> UP BROADCAST RUNNING MULTICAST MTU:1300 Metric:1
> RX packets:39810 errors:0 dropped:0 overruns:0 frame:0
> TX packets:39744 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:27940617 (26.6 MiB) TX bytes:7032624 (6.7 MiB)
03:00.4 SD Host controller: Ricoh Co Ltd MMC/SD Host Controllerlooks fine as long as
> 04:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8057 PCI-E
> Gigabit Ethernet Controller (rev 10)
> 3f:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture
> Generic Non-core Registers (rev 02)
> 3f:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture
> System Address Decoder (rev 02)
> 3f:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02)
> 3f:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev
> 3f:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02)
> 3f:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02)
> > Thanks,
> > Phil
> Thanks for your help
inet addr:192.168.212.53 Bcast:192.168.215.255 Mask:255.255.252.0
is correct for your network? Your wifi is getting an address from a
different subnet. Is that what you want? You may be completely aware but
in case you're not you'll need some routing between the two to get that
working. Have you added some routes for that?
Also, and this is unorthodox, but you might not be getting a default route.
what does route show?
And I know Marvell doesn't like Linux and vis-versa pre 2.6.something.
Although I don't think it would get an address from dhclient if this
were an issue - not sure there - What kernel are you running... uname -r would help