On Mon, 2010-06-07 at 00:33 +0200, Thomas Jollans wrote: > Package: linux-2.6 > Version: 2.6.32-15 > Severity: normal > > My motherboard includes a USB 3.0 controller, handled by the xhci > module. When the xhci module is loaded, the system fails to suspend with > the following log messages: > > [ 458.601622] pm_op(): usb_dev_suspend+0x0/0xa [usbcore] returns -2 > [ 458.601624] PM: Device usb2 failed to suspend: error -2 > > When I unload the xhci module, the system suspends just fine, without > this message. Sarah, any idea what's going on here? Debian version 2.6.32-15 is closely based on stable version 2.6.32.14. I didn't see any later changes to xhci that look related to PM. Ben. > Relevant `lsusb -v` and dmesg output parts follow: > > # lsusb -v > [ ... ] > Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 3.00 > bDeviceClass 9 Hub > bDeviceSubClass 0 Unused > bDeviceProtocol 3 > bMaxPacketSize0 9 > idVendor 0x1d6b Linux Foundation > idProduct 0x0003 3.0 root hub > bcdDevice 2.06 > iManufacturer 3 Linux 2.6.32-5-amd64 xhci_hcd > iProduct 2 xHCI Host Controller > iSerial 1 0000:04:00.0 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 25 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xe0 > Self Powered > Remote Wakeup > MaxPower 0mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 9 Hub > bInterfaceSubClass 0 Unused > bInterfaceProtocol 0 Full speed (or root) hub > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0004 1x 4 bytes > bInterval 12 > Hub Descriptor: > bLength 9 > bDescriptorType 41 > nNbrPorts 4 > wHubCharacteristic 0x0009 > Per-port power switching > Per-port overcurrent protection > TT think time 8 FS bits > bPwrOn2PwrGood 10 * 2 milli seconds > bHubContrCurrent 0 milli Ampere > DeviceRemovable 0x00 > PortPwrCtrlMask 0xff > Hub Port Status: > Port 1: 0000.0100 power > Port 2: 0000.0100 power > Port 3: 0000.0100 power > Port 4: 0000.0100 power > Device Status: 0x0003 > Self Powered > Remote Wakeup Enabled > > # pm-suspend > # dmesg > [ ... ] > [ 457.630373] PM: Syncing filesystems ... done. > [ 457.744997] PM: Preparing system for mem sleep > [ 457.747218] Freezing user space processes ... (elapsed 0.00 seconds) done. > [ 457.747607] Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done. > [ 457.747642] PM: Entering mem sleep > [ 457.747653] Suspending console(s) (use no_console_suspend to debug) > [ 457.812103] sd 3:0:0:0: [sdb] Synchronizing SCSI cache > [ 457.812321] sd 3:0:0:0: [sdb] Stopping disk > [ 458.225455] sd 2:0:0:0: [sda] Synchronizing SCSI cache > [ 458.240627] sd 2:0:0:0: [sda] Stopping disk > [ 458.601622] pm_op(): usb_dev_suspend+0x0/0xa [usbcore] returns -2 > [ 458.601624] PM: Device usb2 failed to suspend: error -2 > [ 458.601626] PM: Some devices failed to suspend > [ 458.822063] sd 2:0:0:0: [sda] Starting disk > [ 460.874188] sd 3:0:0:0: [sdb] Starting disk > [ 465.811159] PM: Finishing wakeup. > [ 465.811160] Restarting tasks ... done. > > # modprobe -r xhci > # pm-suspend > > -- > > Suspend then works without a problem. dmesg output is, as one would expect, > full of what looks to me like routine device suspend, later resume, log > messages. > > The USB 3.0 controller doesn't appear in the USB device list reportbug added below since the module has been unloaded. It appears in the PCI device list, though, in case that helps. > > > -- Package-specific info: > ** Version: > Linux version 2.6.32-5-amd64 (Debian 2.6.32-15) (ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-1) ) #1 SMP Tue Jun 1 04:34:03 UTC 2010 > > ** Command line: > BOOT_IMAGE=/vmlinuz-2.6.32-5-amd64 root=UUID=d6aacc5e-b385-440f-a972-523ec3e3945d ro quiet > > ** Tainted: P (1) > * Proprietary module has been loaded. > > ** Kernel log: > [ removed, irrelevant. See above for relevant log parts. ] > > ** Model information > sys_vendor: Gigabyte Technology Co., Ltd. > product_name: GA-770TA-UD3 > product_version: > chassis_vendor: Gigabyte Technology Co., Ltd. > chassis_version: > bios_vendor: Award Software International, Inc. > bios_version: F2 > board_vendor: Gigabyte Technology Co., Ltd. > board_name: GA-770TA-UD3 > board_version: x.x > > ** Loaded modules: > Module Size Used by > sco 7209 2 > ppdev 5030 0 > lp 7462 0 > bridge 39598 0 > stp 1440 1 bridge > bnep 9427 2 > rfcomm 29581 0 > l2cap 24736 6 bnep,rfcomm > bluetooth 41827 6 sco,bnep,rfcomm,l2cap > rfkill 13044 2 bluetooth > powernow_k8 10978 0 > cpufreq_conservative 5162 0 > cpufreq_userspace 1992 0 > cpufreq_powersave 902 0 > cpufreq_stats 2659 0 > vboxnetadp 4193 0 > vboxnetflt 12415 0 > vboxdrv 1723686 2 vboxnetadp,vboxnetflt > binfmt_misc 6431 1 > fuse 50190 1 > ext4 285611 1 > jbd2 66919 1 ext4 > crc16 1319 2 l2cap,ext4 > ext2 52969 1 > firewire_sbp2 11514 0 > loop 11783 0 > isl6421 1388 1 > cx24123 11111 1 > snd_hda_codec_atihdmi 2251 1 > cx88_dvb 16516 0 > cx88_vp3054_i2c 1636 1 cx88_dvb > videobuf_dvb 4130 1 cx88_dvb > snd_hda_codec_realtek 235506 1 > snd_hda_intel 19907 2 > snd_usb_audio 64070 2 > dvb_core 74570 2 cx88_dvb,videobuf_dvb > snd_hda_codec 54244 3 snd_hda_codec_atihdmi,snd_hda_codec_realtek,snd_hda_intel > snd_usb_lib 13928 1 snd_usb_audio > snd_hwdep 5380 2 snd_usb_audio,snd_hda_codec > cx88_alsa 7843 1 > cx8802 11189 1 cx88_dvb > cx8800 24967 0 > snd_seq_midi 4400 0 > snd_pcm_oss 32591 0 > snd_rawmidi 15515 2 snd_usb_lib,snd_seq_midi > snd_mixer_oss 12606 1 snd_pcm_oss > snd_seq_midi_event 4628 1 snd_seq_midi > snd_pcm 60471 5 snd_hda_intel,snd_usb_audio,snd_hda_codec,cx88_alsa,snd_pcm_oss > snd_seq 42881 2 snd_seq_midi,snd_seq_midi_event > snd_timer 15582 2 snd_pcm,snd_seq > cx88xx 65064 4 cx88_dvb,cx88_alsa,cx8802,cx8800 > snd_seq_device 4493 3 snd_seq_midi,snd_rawmidi,snd_seq > v4l2_common 11720 2 cx8800,cx88xx > ir_common 24271 1 cx88xx > usbhid 33260 0 > videodev 29993 3 cx8800,cx88xx,v4l2_common > snd 46446 23 snd_hda_codec_realtek,snd_hda_intel,snd_usb_audio,snd_hda_codec,snd_hwdep,cx88_alsa,snd_pcm_oss,snd_rawmidi,snd_mixer_oss,snd_pcm,snd_seq,snd_timer,snd_seq_device > soundcore 4598 1 snd > v4l1_compat 11442 1 videodev > i2c_algo_bit 4225 2 cx88_vp3054_i2c,cx88xx > hid 62825 1 usbhid > v4l2_compat_ioctl32 8538 1 videodev > tveeprom 12057 1 cx88xx > videobuf_dma_sg 8403 5 cx88_dvb,cx88_alsa,cx8802,cx8800,cx88xx > btcx_risc 2899 4 cx88_alsa,cx8802,cx8800,cx88xx > videobuf_core 12244 5 videobuf_dvb,cx8802,cx8800,cx88xx,videobuf_dma_sg > fglrx 2385795 31 > i2c_piix4 8328 0 > i2c_core 15712 10 isl6421,cx24123,cx88_vp3054_i2c,cx8800,cx88xx,v4l2_common,videodev,i2c_algo_bit,tveeprom,i2c_piix4 > snd_page_alloc 6249 2 snd_hda_intel,snd_pcm > edac_core 29261 0 > edac_mce_amd 6433 0 > evdev 7352 17 > parport_pc 18855 1 > tpm_tis 7336 0 > tpm 9917 1 tpm_tis > parport 27954 3 ppdev,lp,parport_pc > pcspkr 1699 0 > button 4650 0 > tpm_bios 4521 1 tpm > processor 30231 1 powernow_k8 > ext3 106518 2 > jbd 37085 1 ext3 > mbcache 5050 3 ext4,ext2,ext3 > dm_mod 53754 9 > usb_storage 39449 0 > sg 18744 0 > sr_mod 12602 0 > cdrom 29415 1 sr_mod > sd_mod 29777 7 > crc_t10dif 1276 1 sd_mod > ata_generic 2983 0 > ohci_hcd 19212 0 > firewire_ohci 19468 0 > pata_jmicron 2280 0 > firewire_core 36736 2 firewire_sbp2,firewire_ohci > crc_itu_t 1307 1 firewire_core > pata_atiixp 3489 0 > ahci 32358 5 > ehci_hcd 31039 0 > r8169 28877 0 > mii 3210 1 r8169 > usbcore 121959 7 snd_usb_audio,snd_usb_lib,usbhid,usb_storage,ohci_hcd,ehci_hcd > nls_base 6361 1 usbcore > libata 133520 4 ata_generic,pata_jmicron,pata_atiixp,ahci > scsi_mod 122117 6 firewire_sbp2,usb_storage,sg,sr_mod,sd_mod,libata > thermal 11674 0 > thermal_sys 11942 2 processor,thermal > > ** PCI devices: > 00:00.0 Host bridge [0600]: ATI Technologies Inc RX780/RX790 Chipset Host Bridge [1002:5957] > Subsystem: ATI Technologies Inc RX780/RX790 Chipset Host Bridge [1002:5957] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- > Latency: 32 > Region 3: Memory at <ignored> (64-bit, non-prefetchable) > Capabilities: <access denied> > > 00:02.0 PCI bridge [0604]: ATI Technologies Inc RD790 PCI to PCI bridge (external gfx0 port A) [1002:5978] (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > I/O behind bridge: 0000a000-0000afff > Memory behind bridge: fdf00000-fdffffff > Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport > Kernel modules: shpchp > > 00:06.0 PCI bridge [0604]: ATI Technologies Inc RD790 PCI to PCI bridge (PCI express gpp port C) [1002:597c] (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 > I/O behind bridge: 0000e000-0000efff > Memory behind bridge: fde00000-fdefffff > Prefetchable memory behind bridge: 00000000fdd00000-00000000fddfffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport > Kernel modules: shpchp > > 00:07.0 PCI bridge [0604]: ATI Technologies Inc RD790 PCI to PCI bridge (PCI express gpp port D) [1002:597d] (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 > I/O behind bridge: 0000d000-0000dfff > Memory behind bridge: fdc00000-fdcfffff > Prefetchable memory behind bridge: 00000000fdb00000-00000000fdbfffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport > Kernel modules: shpchp > > 00:09.0 PCI bridge [0604]: ATI Technologies Inc RD790 PCI to PCI bridge (PCI express gpp port E) [1002:597e] (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 > I/O behind bridge: 0000c000-0000cfff > Memory behind bridge: fda00000-fdafffff > Prefetchable memory behind bridge: 00000000fd900000-00000000fd9fffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport > Kernel modules: shpchp > > 00:0a.0 PCI bridge [0604]: ATI Technologies Inc RD790 PCI to PCI bridge (PCI express gpp port F) [1002:597f] (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 > I/O behind bridge: 0000b000-0000bfff > Memory behind bridge: fd800000-fd8fffff > Prefetchable memory behind bridge: 00000000fd600000-00000000fd6fffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport > Kernel modules: shpchp > > 00:11.0 SATA controller [0106]: ATI Technologies Inc SB700/SB800 SATA Controller [IDE mode] [1002:4390] (prog-if 01 [AHCI 1.0]) > Subsystem: Giga-byte Technology Device [1458:b002] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 32, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 22 > Region 0: I/O ports at ff00 [size=8] > Region 1: I/O ports at fe00 [size=4] > Region 2: I/O ports at fd00 [size=8] > Region 3: I/O ports at fc00 [size=4] > Region 4: I/O ports at fb00 [size=16] > Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=1K] > Capabilities: <access denied> > Kernel driver in use: ahci > Kernel modules: ahci > > 00:12.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI]) > Subsystem: Giga-byte Technology Device [1458:5004] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 32, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 16 > Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=4K] > Kernel driver in use: ohci_hcd > Kernel modules: ohci-hcd > > 00:12.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1 Controller [1002:4398] (prog-if 10 [OHCI]) > Subsystem: Giga-byte Technology Device [1458:5004] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 32, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 16 > Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K] > Kernel driver in use: ohci_hcd > Kernel modules: ohci-hcd > > 00:12.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI]) > Subsystem: Giga-byte Technology Device [1458:5004] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 32, Cache Line Size: 64 bytes > Interrupt: pin B routed to IRQ 17 > Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=256] > Capabilities: <access denied> > Kernel driver in use: ehci_hcd > Kernel modules: ehci-hcd > > 00:13.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI]) > Subsystem: Giga-byte Technology Device [1458:5004] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 32, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 18 > Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K] > Kernel driver in use: ohci_hcd > Kernel modules: ohci-hcd > > 00:13.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1 Controller [1002:4398] (prog-if 10 [OHCI]) > Subsystem: Giga-byte Technology Device [1458:5004] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 32, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 18 > Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K] > Kernel driver in use: ohci_hcd > Kernel modules: ohci-hcd > > 00:13.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI]) > Subsystem: Giga-byte Technology Device [1458:5004] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 32, Cache Line Size: 64 bytes > Interrupt: pin B routed to IRQ 19 > Region 0: Memory at fe029000 (32-bit, non-prefetchable) [size=256] > Capabilities: <access denied> > Kernel driver in use: ehci_hcd > Kernel modules: ehci-hcd > > 00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385] (rev 3c) > Subsystem: Giga-byte Technology Device [1458:4385] > Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Capabilities: <access denied> > Kernel modules: i2c-piix4 > > 00:14.1 IDE interface [0101]: ATI Technologies Inc SB700/SB800 IDE Controller [1002:439c] (prog-if 8a [Master SecP PriP]) > Subsystem: Giga-byte Technology Device [1458:5002] > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 32, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 16 > Region 0: I/O ports at 01f0 [size=8] > Region 1: I/O ports at 03f4 [size=1] > Region 2: I/O ports at 0170 [size=8] > Region 3: I/O ports at 0374 [size=1] > Region 4: I/O ports at fa00 [size=16] > Capabilities: <access denied> > Kernel driver in use: pata_atiixp > Kernel modules: ata_generic, pata_atiixp > > 00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia (Intel HDA) [1002:4383] > Subsystem: Giga-byte Technology Device [1458:a002] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 32, Cache Line Size: 64 bytes > Interrupt: pin ? routed to IRQ 16 > Region 0: Memory at fe024000 (64-bit, non-prefetchable) [size=16K] > Capabilities: <access denied> > Kernel driver in use: HDA Intel > Kernel modules: snd-hda-intel > > 00:14.3 ISA bridge [0601]: ATI Technologies Inc SB700/SB800 LPC host controller [1002:439d] > Subsystem: ATI Technologies Inc SB700/SB800 LPC host controller [1002:439d] > Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > > 00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge [1002:4384] (prog-if 01 [Subtractive decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 64 > Bus: primary=00, secondary=06, subordinate=06, sec-latency=64 > I/O behind bridge: 00009000-00009fff > Memory behind bridge: f8000000-fcffffff > Prefetchable memory behind bridge: fd700000-fd7fffff > Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > > 00:14.5 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller [1002:4399] (prog-if 10 [OHCI]) > Subsystem: Giga-byte Technology Device [1458:5004] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 32, Cache Line Size: 64 bytes > Interrupt: pin C routed to IRQ 18 > Region 0: Memory at fe028000 (32-bit, non-prefetchable) [size=4K] > Kernel driver in use: ohci_hcd > Kernel modules: ohci-hcd > > 00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration [1022:1200] > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Capabilities: <access denied> > > 00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map [1022:1201] > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > > 00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller [1022:1202] > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Kernel modules: amd64_edac_mod > > 00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control [1022:1203] > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Capabilities: <access denied> > > 00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control [1022:1204] > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > > 01:00.0 VGA compatible controller [0300]: ATI Technologies Inc RV710 [Radeon HD 4550] [1002:9540] (prog-if 00 [VGA controller]) > Subsystem: Giga-byte Technology Device [1458:21ae] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 31 > Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M] > Region 2: Memory at fdfe0000 (64-bit, non-prefetchable) [size=64K] > Region 4: I/O ports at ae00 [size=256] > [virtual] Expansion ROM at fdf00000 [disabled] [size=128K] > Capabilities: <access denied> > Kernel driver in use: fglrx_pci > Kernel modules: radeon > > 01:00.1 Audio device [0403]: ATI Technologies Inc RV710/730 [1002:aa38] > Subsystem: Giga-byte Technology Device [1458:aa38] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin B routed to IRQ 19 > Region 0: Memory at fdffc000 (64-bit, non-prefetchable) [size=16K] > Capabilities: <access denied> > Kernel driver in use: HDA Intel > Kernel modules: snd-hda-intel > > 02:00.0 SATA controller [0106]: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller [197b:2363] (rev 03) (prog-if 01 [AHCI 1.0]) > Subsystem: Giga-byte Technology GA-EP45-DS5 Motherboard [1458:b000] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 18 > Region 5: Memory at fdefe000 (32-bit, non-prefetchable) [size=8K] > Capabilities: <access denied> > Kernel driver in use: ahci > Kernel modules: ahci > > 02:00.1 IDE interface [0101]: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller [197b:2363] (rev 03) (prog-if 85 [Master SecO PriO]) > Subsystem: Giga-byte Technology GA-EP45-DS5 Motherboard [1458:b000] > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin B routed to IRQ 19 > Region 0: I/O ports at ef00 [size=8] > Region 1: I/O ports at ee00 [size=4] > Region 2: I/O ports at ed00 [size=8] > Region 3: I/O ports at ec00 [size=4] > Region 4: I/O ports at eb00 [size=16] > Capabilities: <access denied> > Kernel driver in use: pata_jmicron > Kernel modules: pata_jmicron, ata_generic > > 03:00.0 IDE interface [0101]: Device [1b4b:91a3] (rev 11) (prog-if 8f [Master SecP SecO PriP PriO]) > Subsystem: Giga-byte Technology Device [1458:b000] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 5 > Region 0: I/O ports at df00 [size=8] > Region 1: I/O ports at de00 [size=4] > Region 2: I/O ports at dd00 [size=8] > Region 3: I/O ports at dc00 [size=4] > Region 4: I/O ports at db00 [size=16] > Region 5: Memory at fdcff000 (32-bit, non-prefetchable) [size=2K] > [virtual] Expansion ROM at fdb00000 [disabled] [size=64K] > Capabilities: <access denied> > Kernel modules: ata_generic > > 04:00.0 USB Controller [0c03]: NEC Corporation uPD720200 USB 3.0 Host Controller [1033:0194] (rev 03) (prog-if 30) > Subsystem: Giga-byte Technology Device [1458:5007] > Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Interrupt: pin A routed to IRQ 17 > Region 0: Memory at fdafe000 (64-bit, non-prefetchable) [size=8K] > Capabilities: <access denied> > Kernel modules: xhci > > 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 03) > Subsystem: Giga-byte Technology GA-EP45-DS5 Motherboard [1458:e000] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 30 > Region 0: I/O ports at be00 [size=256] > Region 2: Memory at fd6ff000 (64-bit, prefetchable) [size=4K] > Region 4: Memory at fd6f8000 (64-bit, prefetchable) [size=16K] > [virtual] Expansion ROM at fd600000 [disabled] [size=128K] > Capabilities: <access denied> > Kernel driver in use: r8169 > Kernel modules: r8169 > > 06:07.0 Multimedia video controller [0400]: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [14f1:8800] (rev 05) > Subsystem: Hauppauge computer works Inc. Nova-S-Plus DVB-S [0070:9202] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 32 (5000ns min, 13750ns max), Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 21 > Region 0: Memory at f9000000 (32-bit, non-prefetchable) [size=16M] > Capabilities: <access denied> > Kernel driver in use: cx8800 > Kernel modules: cx8800 > > 06:07.1 Multimedia controller [0480]: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port] [14f1:8801] (rev 05) > Subsystem: Hauppauge computer works Inc. Device [0070:9202] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 32 (1000ns min, 63750ns max), Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 21 > Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=16M] > Capabilities: <access denied> > Kernel driver in use: cx88_audio > Kernel modules: cx88-alsa > > 06:07.2 Multimedia controller [0480]: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] [14f1:8802] (rev 05) > Subsystem: Hauppauge computer works Inc. Device [0070:9202] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 32 (1500ns min, 22000ns max), Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 21 > Region 0: Memory at fb000000 (32-bit, non-prefetchable) [size=16M] > Capabilities: <access denied> > Kernel driver in use: cx88-mpeg driver manager > Kernel modules: cx8802 > > 06:07.4 Multimedia controller [0480]: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [IR Port] [14f1:8804] (rev 05) > Subsystem: Hauppauge computer works Inc. Device [0070:9202] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 32 (1500ns min, 63750ns max), Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 3 > Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M] > Capabilities: <access denied> > > 06:0e.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) [104c:8024] (prog-if 10 [OHCI]) > Subsystem: Giga-byte Technology GA-EP45-DS5 Motherboard [1458:1000] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 32 (500ns min, 1000ns max), Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 22 > Region 0: Memory at fcfff000 (32-bit, non-prefetchable) [size=2K] > Region 1: Memory at fcff8000 (32-bit, non-prefetchable) [size=16K] > Capabilities: <access denied> > Kernel driver in use: firewire_ohci > Kernel modules: firewire-ohci > > > ** USB devices: > Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 007 Device 003: ID 08bb:2900 Texas Instruments Japan PCM2900 Audio Codec > Bus 007 Device 002: ID 058f:9254 Alcor Micro Corp. Hub > Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 004 Device 002: ID 1307:0330 Transcend Information, Inc. > Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 001 Device 003: ID 046d:c046 Logitech, Inc. RX1000 Laser Mouse > Bus 001 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB > Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > > > -- System Information: > Debian Release: squeeze/sid > APT prefers unstable > APT policy: (500, 'unstable') > Architecture: amd64 (x86_64) > > Kernel: Linux 2.6.32-5-amd64 (SMP w/4 CPU cores) > Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8) > Shell: /bin/sh linked to /bin/dash > > Versions of packages linux-image-2.6.32-5-amd64 depends on: > ii debconf [debconf-2.0] 1.5.32 Debian configuration management sy > ii initramfs-tools [linux-initr 0.95.1 tools for generating an initramfs > ii linux-base 2.6.32-15 Linux image base package > ii module-init-tools 3.12~pre2-3 tools for managing Linux kernel mo > > Versions of packages linux-image-2.6.32-5-amd64 recommends: > ii firmware-linux-free 2.6.32-15 Binary firmware for various driver > > Versions of packages linux-image-2.6.32-5-amd64 suggests: > ii grub 0.97-61 GRand Unified Bootloader (dummy pa > pn linux-doc-2.6.32 <none> (no description available) > > Versions of packages linux-image-2.6.32-5-amd64 is related to: > pn firmware-bnx2 <none> (no description available) > pn firmware-bnx2x <none> (no description available) > pn firmware-ipw2x00 <none> (no description available) > pn firmware-ivtv <none> (no description available) > pn firmware-iwlwifi <none> (no description available) > pn firmware-linux <none> (no description available) > pn firmware-linux-nonfree <none> (no description available) > pn firmware-qlogic <none> (no description available) > pn firmware-ralink <none> (no description available) > pn xen-hypervisor <none> (no description available) > > -- debconf information excluded > > > -- Ben Hutchings Once a job is fouled up, anything done to improve it makes it worse.
Attachment:
signature.asc
Description: This is a digitally signed message part