Bug#390905: (no subject)
Package: linux-image-2.6.17-2-686
Version: 2.6.17-9
Severity: normal
When attempting to boot 2.6.17-2-686 on a dell 2950, the kernel oopses
when I'm using a serial console, but boots ok when I'm not. A hardware
reset is necessary to get access to the machine back. I'm using ipmi
sol to access the console. Below is the complete boot log, apologies
if this is too long.
GNU GRUB version 0.97 (640K lower / 3406496K upper memory)
Booting 'Debian GNU/Linux, kernel 2.6.17-2-686'
i r e 1
root (hd0,0)
Filesystem type is ext2fs,cpartition type 0x83 .
kernel /boot/vmlinuz-2.6.17-2-686
root=/dev/sda1urorconsole=ttyS1,57600n8
[Linux-bzImage, setup=0x1e00, size=0x12668e]
initrd /boot/initrd.img-2.6.17-2-686
[Linux-initrd @ 0x2fb31000, 0x4beefc bytes]
savedefault
Linux version 2.6.17-2-686 (Debian 2.6.17-9) (waldi@debian.org) (gcc
version 4.6BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000
(usable)───────────────────
BIOS-e820: 0000000000100000 - 00000000cffa8000 (usable)
BIOS-e820: 00000000cffa8000 - 00000000cffb7c00 (ACPI data)
BIOS-e820: 00000000cffb7c00 - 00000000d0000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fe000000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000130000000 (usable)
Warning only 4GB will be used.
Use a PAE enabled kernel.
2944MB HIGHMEM available.
1152MB LOWMEM available.
found SMP MP-table at 000fe710
DMI 2.4 present.
ACPI: PM-Timer IO Port: 0x808
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x13] disabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] disabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x15] disabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] disabled)
ACPI: LAPIC (acpi_id[0x08] lapic_id[0x17] disabled)
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x03] address[0xfec81000] gsi_base[64])
IOAPIC[1]: apic_id 3, version 32, address 0xfec81000, GSI 64-87
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Enabling APIC mode: Flat. Using 2 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at d1000000 (gap: d0000000:10000000)
Built 1 zonelists
Kernel command line: root=/dev/sda1 ro console=ttyS1,57600n8
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 131072 (order: 7, 524288 bytes)
Memory: 3364336k/4194304k available (1482k kernel code, 41872k reserved,
544k d)Checking if this processor honours the WP bit even in supervisor
mode... Ok.
hpet0: at MMIO 0xfed00000 (virtual 0xf8800000), IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
Using HPET for base-timer
Using HPET for gettimeofday
Detected 1995.024 MHz processor.
Using hpet for high-res timesource
Calibrating delay using timer specific routine.. 3993.17 BogoMIPS
(lpj=7986351)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
CPU0: Intel(R) Xeon(R) CPU 5130 @ 2.00GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3990.08 BogoMIPS
(lpj=7980160)
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Xeon(R) CPU 5130 @ 2.00GHz stepping 06
Total of 2 processors activated (7983.25 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=8000
checking if image is initramfs... it is
Freeing initrd memory: 4859k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Link [LK00] (IRQs 3 4 *5 6 7 10 11 12)
ACPI: PCI Interrupt Link [LK01] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LK02] (IRQs 3 4 5 *6 7 10 11 12)
ACPI: PCI Interrupt Link [LK03] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK04] (IRQs 3 4 5 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LK05] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK06] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LK07] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
pnp: 00:08: ioport range 0x800-0x87f could not be reserved
pnp: 00:08: ioport range 0x880-0x8bf has been reserved
pnp: 00:08: ioport range 0x8c0-0x8df has been reserved
pnp: 00:08: ioport range 0x8e0-0x8e3 has been reserved
pnp: 00:08: ioport range 0xc00-0xc7f has been reserved
pnp: 00:08: ioport range 0xca0-0xca7 has been reserved
pnp: 00:08: ioport range 0xca9-0xcab has been reserved
pnp: 00:08: ioport range 0xcad-0xcaf has been reserved
pnp: 00:09: ioport range 0xca8-0xca8 has been reserved
pnp: 00:09: ioport range 0xcac-0xcac has been reserved
PCI: Bridge: 0000:08:00.0
IO window: disabled.
MEM window: f4000000-f7ffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:07:00.0
IO window: disabled.
MEM window: f4000000-f7ffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:07:01.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:06:00.0
IO window: disabled.
MEM window: f4000000-f7ffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:06:00.3
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:02.0
IO window: disabled.
MEM window: f2000000-f7ffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:01:00.0
IO window: disabled.
MEM window: fc400000-fc5fffff
PREFETCH window: d8000000-d80fffff
PCI: Bridge: 0000:01:00.2
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:03.0
IO window: disabled.
MEM window: fc300000-fc5fffff
PREFETCH window: d8000000-d80fffff
PCI: Bridge: 0000:00:04.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:05.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:06.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:07.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:04:00.0
IO window: disabled.
MEM window: f8000000-fbffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: f8000000-fbffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: e000-efff
MEM window: fc100000-fc2fffff
PREFETCH window: d0000000-d7ffffff
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI Interrupt 0000:07:00.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI Interrupt 0000:07:01.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 169
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 524288 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1159807595.252:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 169
assign_interrupt_mode Found MSI capability
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 16 (level, low) -> IRQ 169
assign_interrupt_mode Found MSI capability
ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 16 (level, low) -> IRQ 169
assign_interrupt_mode Found MSI capability
pcie_portdrv_probe->Dev[25e5:8086] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 16 (level, low) -> IRQ 169
assign_interrupt_mode Found MSI capability
pcie_portdrv_probe->Dev[25e7:8086] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 169
assign_interrupt_mode Found MSI capability
ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI Interrupt 0000:07:00.0[A] -> GSI 16 (level, low) -> IRQ 169
assign_interrupt_mode Found MSI capability
ACPI: PCI Interrupt 0000:07:01.0[A] -> GSI 16 (level, low) -> IRQ 169
assign_interrupt_mode Found MSI capability
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Starting balanced_irq
Using IPI No-Shortcut mode
ACPI wakeup devices:
PCI0
ACPI: (supports S0 S4 S5)
Freeing unused kernel memory: 196k freed
Loading, please wait...
Begin: Loading essential drivers... ...
SCSI subsystem initialized
megasas: 00.00.02.04 Fri Feb 03 14:31:44 PST 2006
megasas: 0x1028:0x0015:0x1028:0x1f03: bus 2:slot 14:func 0
ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 78 (level, low) -> IRQ 66
scsi0 : LSI Logic SAS based MegaRAID driver
Vendor: SEAGATE Model: ST373454SS Rev: S410
Type: Direct-Access ANSI SCSI revision: 05
Vendor: SEAGATE Model: ST373454SS Rev: S410
Type: Direct-Access ANSI SCSI revision: 05
Vendor: DP Model: BACKPLANE Rev: 1.00
Type: Enclosure ANSI SCSI revision: 05
Vendor: DELL Model: PERC 5/i Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 05
Done.
Begin: Running /scripts/init-premount ...
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.4.40 (May 22,
2006)
ACPI: PCI Interrupt 0000:09:00.0[A] -> GSI 16 (level, low) -> IRQ 169
eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B1) PCI-X 64-bit 133MHz
found a9ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 16 (level, low) ->
IRQ 169
eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B1) PCI-X 64-bit 133MHz
found a7Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
usbcore: registered new driver usbfs
usbcore: registered new driver hub
SCSI device sda: 142082048 512-byte hdwr sectors (72746 MB)
ESB2: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 169
ESB2: chipset revision 9
ESB2: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
sda: test WP failed, assume Write Enabled
USB Universal Host Controller Interface driver v3.0
sda: asking for cache data failed
sda: assuming drive cache: write through
SCSI device sda: 142082048 512-byte hdwr sectors (72746 MB)
sda: test WP failed, assume Write Enabled
sda: asking for cache data failed
sda: assuming drive cache: write through
sda: sda1 sda2
sd 0:2:0:0: Attached scsi disk sda
hda: TSSTcorpCD-RW/DVD-ROM TSL462C, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 21 (level, low) -> IRQ 74
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 74, io base 0x0000dce0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hda: ATAPI 24X DVD-ROM CD-R/RW drive, 1536kB Cache, UDMA(33)
Uniform CD-ROM driver RevisiI 20 (level, low) -> IRQ 82
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 82, io base 0x0000dcc0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 21 (level, low) -> IRQ 74
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 74, io base 0x0000dca0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-1: new full speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 21 (level, low) -> IRQ 74
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: irq 74, io mem 0xfc600000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
Done.
Begin: Mounting root file system... ...
Begin: Running /scripts/local-top ...
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com
usb 1-1: device not accepting address 2, error -71
hda: packet command error: status=0x51 { DriveReady SeekComplete Error }
hda: packet command error: error=0x54 { AbortedCommand
LastFailedSense=0x05 }
ide: failed opcode was: unknown
5 logical volume(s) in volume group "sunvg00" now active
Done.
Begin: Running /scripts/local-premount ...
Attempting manual resume
kinit: name_to_dev_t(/dev/mapper/sunvg00-swap) = dm-3(254,3)
kinit: trying to resume from /dev/kjournald starting. Commit interval 5
secondsmapper/sunvg00-sEXT3-fs: mounted filesystem with ordered data
mode.
wap
kinit: No resume image, doing normal boot...
Done.
Begin: Running /scripts/local-bottom ...
Done.
Done.
Begin: Running /scripts/init-bottom ...
Done.
INIT: version 2.86 booting
usb 4-1: new high speed USB device using ehci_hcd and address 2
usb 4-1: configuration #1 chosen from 1 choice
hub 4-1:1.0: USB hub found
hub 4-1:1.0: 2 ports detected
Setting hostname to 'sundance'...done.
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...usb 4-5: new high speed USB
device usi3usb 4-5: configuration #1 chosen from 1 choice
hub 4-5:1.0: USB hub found
hub 4-5:1.0: 4 ports detected
Real Time Clock Driver v1.12ac
usb 4-1.1: new full speed USB device using ehci_hcd and address 4
00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
hw_random hardware driver 1.0.0 loaded
usb 4-1.1: configuration #1 chosen from 1 choice
usb 4-1.2: new high speed USB device using ehci_hcd and address 5
usb 4-1.2: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: Dell DRAC5 as /class/input/input0
input: USB HID v1.10 Keyboard [Dell DRAC5] on usb-0000:00:1d.7-1.1
input: Dell DRAC5 as /class/input/input1
input: USB HID v1.10 Mouse [Dell DRAC5] on usb-0000:00:1d.7-1.1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Initializing USB Mass Storage driver...
scsi1 : SCSI emulation for USB Mass Storage devices
mice: PS/2 mouse device common for all mice
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
floppy0: no floppy controllers found
BUG: unable to handle kernel NULL pointer dereference at virtual address
000000c printing eip:
b0200282
*pde = 00000000
Oops: 0000 [#1]
SMP
Modules linked in: joydev mousedev usb_storage evdev usbhid psmouse
serio_raw hdCPU: 1
EIP: 0060:[<b0200282>] Not tainted VLI
EFLAGS: 00010206 (2.6.17-2-686 #1)
EIP is at uart_write_room+0x9/0x16
eax: dff34428 ebx: 00000006 ecx: dff5f540 edx: 00000000
esi: b325f800 edi: b32c8c00 ebp: 00000006 esp: dfe0df18
ds: 007b es: 007b ss: 0068
Process S03udev (pid: 2165, threadinfo=dfe0c000 task=dff5f540)
Stack: b01f456d b32c8c00 dfa27d40 00000282 00000000 dff5f540 b0116f2d
b325f938
b325f938 00000006 b325f800 00000006 00000006 b01f21d3 00000006
080f6408
dfa27d40 b01f448c b325f80c b325fbe8 00000000 b01f2b64 dfa27d40
dfa27d40
Call Trace:
<b01f456d> write_chan+0xe1/0x293 <b0116f2d>
default_wake_function+0x0/0xc
<b01f21d3> tty_write+0x147/0x1d8 <b01f448c> write_chan+0x0/0x293
<b01f2b64> redirected_tty_write+0x1c/0x6c <b01f2b48>
redirected_tty_write+0x0c <b0153379> vfs_write+0xa1/0x140 <b0153963>
sys_write+0x3c/0x63
<b0102ae7> sysenter_past_esp+0x54/0x75
Code: 09 08 8b 40 10 74 09 81 60 10 ff ff ff fd eb 07 81 48 10 00 00 00
02 8b 5
EIP: [<b0200282>] uart_write_room+0x9/0x16 SS:ESP 0068:dfe0df18
<5> Vendor: Dell Model: Virtual CDROM Rev: 123
Type: CD-ROM ANSI SCSI revision: 00
usb-storage: device scan complete
Vendor: Dell Model: Virtual Floppy Rev: 123
Type: Direct-Access ANSI SCSI revision: 00
sd 2:0:0:0: Attached scsi removable disk sdb
sr0: scsi-1 drive
sr 1:0:0:0: Attached scsi CD-ROM sr0
usb-storage: device scan complete
0:0:8:0: Attached scsi generic sg0 type 13
sd 0:2:0:0: Attached scsi generic sg1 type 0
sr 1:0:0:0: Attached scsi generic sg2 type 5
sd 2:0:0:0: Attached scsi generic sg3 type 0
This is where it hangs. Note, this works just fine with the
2.6.16-2-686.
Thanks.
-- System Information:
Debian Release: testing/unstable
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Shell: /bin/sh linked to /bin/bash
Kernel: Linux 2.6.16-2-686
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Versions of packages linux-image-2.6.17-2-686 depends on:
ii initramfs-tools [linux-initra 0.80 tools for generating an
initramfs
ii module-init-tools 3.2.2-3 tools for managing Linux
kernel mo
Versions of packages linux-image-2.6.17-2-686 recommends:
pn libc6-i686 <none> (no description available)
-- debconf information:
linux-image-2.6.17-2-686/postinst/old-initrd-link-2.6.17-2-686: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.17-2-686/postinst/old-dir-initrd-link-2.6.17-2-686: true
linux-image-2.6.17-2-686/preinst/lilo-initrd-2.6.17-2-686: true
linux-image-2.6.17-2-686/preinst/failed-to-move-modules-2.6.17-2-686:
linux-image-2.6.17-2-686/postinst/depmod-error-initrd-2.6.17-2-686: false
linux-image-2.6.17-2-686/postinst/create-kimage-link-2.6.17-2-686: true
linux-image-2.6.17-2-686/preinst/abort-install-2.6.17-2-686:
linux-image-2.6.17-2-686/postinst/bootloader-test-error-2.6.17-2-686:
linux-image-2.6.17-2-686/preinst/lilo-has-ramdisk:
linux-image-2.6.17-2-686/prerm/removing-running-kernel-2.6.17-2-686: true
linux-image-2.6.17-2-686/preinst/overwriting-modules-2.6.17-2-686: true
linux-image-2.6.17-2-686/preinst/abort-overwrite-2.6.17-2-686:
linux-image-2.6.17-2-686/preinst/already-running-this-2.6.17-2-686:
linux-image-2.6.17-2-686/postinst/old-system-map-link-2.6.17-2-686: true
linux-image-2.6.17-2-686/postinst/kimage-is-a-directory:
linux-image-2.6.17-2-686/preinst/elilo-initrd-2.6.17-2-686: true
linux-image-2.6.17-2-686/preinst/bootloader-initrd-2.6.17-2-686: true
linux-image-2.6.17-2-686/prerm/would-invalidate-boot-loader-2.6.17-2-686:
true
linux-image-2.6.17-2-686/postinst/depmod-error-2.6.17-2-686: false
linux-image-2.6.17-2-686/postinst/bootloader-error-2.6.17-2-686:
linux-image-2.6.17-2-686/preinst/initrd-2.6.17-2-686:
Reply to: