Bug#315931: kernel-image-2.6.8-2-k7: dmesg, lsmod
Package: kernel-image-2.6.8-2-k7
Version: 2.6.8-16
Followup-For: Bug #315931
dmesg:
Linux version 2.6.8-2-k7 (horms@tabatha.lab.ultramonkey.org) (gcc version 3.3.5 (Debian 1:3.3.5-12)) #1 Thu May 19 18:03:29 JST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001eff0000 (usable)
BIOS-e820: 000000001eff0000 - 000000001eff3000 (ACPI NVS)
BIOS-e820: 000000001eff3000 - 000000001f000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
495MB LOWMEM available.
On node 0 totalpages: 126960
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 122864 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 KM266P ) @ 0x000f6b10
ACPI: RSDT (v001 KM266P AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1eff3040
ACPI: FADT (v001 KM266P AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1eff30c0
ACPI: DSDT (v001 KM266P AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 1825.925 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 495540k/507840k available (1536k kernel code, 11552k reserved, 697k data, 148k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3629.05 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Sempron(tm) 2600+ stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1825.0594 MHz.
..... host bus clock speed is 331.0926 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4496k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb750, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: IRQ9 SCI: Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 12) *5
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 *12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fc190
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xc1c0, dseg 0xf0000
spurious 8259A interrupt: IRQ7.
PnPBIOS: 10 nodes reported by PnP BIOS; 10 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:11.1[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 10 (level, low) -> IRQ 10
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Failed to disable AUX port, but continuing anyway... Is this a SiS?
If AUX port is really absent please use the 'i8042.noaux' option.
serio: i8042 KBD port at 0x60,0x64 irq 1
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4496 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 148k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI interrupt 0000:00:11.1[A] -> GSI 10 (level, low) -> IRQ 10
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xe400-0xe407, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xe408-0xe40f, BIOS settings: hdc:pio, hdd:pio
hda: HDS728080PLAT20, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
hda: 160836480 sectors (82348 MB) w/1719KiB Cache, CHS=16383/255/63, UDMA(133)
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 >
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: hda1: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 9633799
ext3_orphan_cleanup: deleting unreferenced inode 9633798
ext3_orphan_cleanup: deleting unreferenced inode 9633797
EXT3-fs: hda1: 3 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1461872k swap on /dev/hda5. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
Generic RTC Driver v1.07
Capability LSM initialized
irda_init()
NET: Registered protocol family 23
e100: Intel(R) PRO/100 Network Driver, 3.0.18
e100: Copyright(c) 1999-2004 Intel Corporation
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 11 (level, low) -> IRQ 11
e100: eth0: e100_probe: addr 0xee431000, irq 11, MAC addr 00:0E:0C:6B:E9:01
e100: eth0: e100_watchdog: link up, 10Mbps, full-duplex
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02fc1a0(lo)
IPv6 over IPv4 tunneling driver
process `cyrmaster' is using obsolete setsockopt SO_BSDCOMPAT
eth0: no IPv6 routers present
Assertion failure in journal_put_journal_head() at fs/jbd/journal.c:1824: "jh->b_jcount > 0"
------------[ cut here ]------------
kernel BUG at fs/jbd/journal.c:1824!
invalid operand: 0000 [#1]
PREEMPT
Modules linked in: ipv6 e100 mii via_ircc irda crc_ccitt capability commoncap ide_cd cdrom genrtc ext3 jbd mbcache ide_generic via82cxxx ide_disk ide_core unix font vesafb cfbcopyarea cfbimgblt cfbfillrect
CPU: 0
EIP: 0060:[<df8951ac>] Not tainted
EFLAGS: 00010286 (2.6.8-2-k7)
EIP is at journal_put_journal_head+0x9c/0xb0 [jbd]
eax: 00000060 ebx: ca9964ac ecx: c02bb418 edx: c02bb418
esi: 004c004c edi: dee68000 ebp: d29ed96c esp: dee69da0
ds: 007b es: 007b ss: 0068
Process kswapd0 (pid: 36, threadinfo=dee68000 task=dee305e0)
Stack: df8965c0 df895615 df896f4e 00000720 df897071 d29ed96c ca9964ac df88efb1
ca9964ac d29ed96c cf8cf644 00000012 d66484a4 00000000 c119a120 deb7b840
dee68000 dee69ebc df8a3351 deb7b840 c119a120 000000d0 deb54afc 00000000
Call Trace:
[<df88efb1>] journal_try_to_free_buffers+0x61/0xe0 [jbd]
[<df8a3351>] ext3_releasepage+0x41/0x80 [ext3]
[<c0156841>] try_to_release_page+0x51/0x70
[<c0140e5c>] shrink_list+0x3cc/0x4d0
[<c013fd6d>] __pagevec_lru_add+0xcd/0x100
[<c01410aa>] shrink_cache+0x14a/0x340
[<c014078a>] shrink_slab+0x8a/0x190
[<c014185a>] shrink_zone+0x9a/0xc0
[<c0141c81>] balance_pgdat+0x211/0x280
[<c0141db7>] kswapd+0xc7/0xe0
[<c0119d30>] autoremove_wake_function+0x0/0x60
[<c0105fde>] ret_from_fork+0x6/0x14
[<c0119d30>] autoremove_wake_function+0x0/0x60
[<c0141cf0>] kswapd+0x0/0xe0
[<c0104291>] kernel_thread_helper+0x5/0x14
Code: 0f 0b 20 07 4e 6f 89 df 8b 43 04 e9 76 ff ff ff 8d 74 26 00
<6>note: kswapd0[36] exited with preempt_count 2
Adding 1461872k swap on /dev/hda5. Priority:-2 extents:1
And here is lsmod:
ipv6 262468 22
e100 33344 0
mii 5184 1 e100
via_ircc 26448 0
irda 195712 1 via_ircc
crc_ccitt 2176 1 irda
capability 4616 0
commoncap 7296 1 capability
ide_cd 42528 0
cdrom 40284 1 ide_cd
genrtc 9652 0
ext3 126760 1
jbd 61848 1 ext3
mbcache 9284 1 ext3
ide_generic 1472 0
via82cxxx 13980 1
ide_disk 19264 3
ide_core 138724 4 ide_cd,ide_generic,via82cxxx,ide_disk
unix 28660 280
font 8448 0
vesafb 6688 0
cfbcopyarea 3840 1 vesafb
cfbimgblt 3072 1 vesafb
cfbfillrect 3712 1 vesafb
Thanks,
Dave
-- System Information:
Debian Release: 3.1
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.8-2-k7
Locale: LANG=en_US, LC_CTYPE=en_US (charmap=ISO-8859-1)
Versions of packages kernel-image-2.6.8-2-k7 depends on:
ii coreutils [fileutils] 5.2.1-2 The GNU core utilities
ii initrd-tools 0.1.81.1 tools to create initrd image for p
ii module-init-tools 3.2-pre1-2 tools for managing Linux kernel mo
-- no debconf information
Reply to: