Package: installation-reports Version: 2.29 Severity: normal -- Package-specific info: Boot method: netinst cd Image version: netinst, etch 4.0r2 installer Date: 2008-02-01 Machine: HP Compaq 6720s Partitions: Disk /dev/sda: 120.0 GB, 120034123776 bytes 255 heads, 63 sectors/track, 14593 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 * 1 31 248976 83 Linux /dev/sda2 32 14593 116969265 5 Extended /dev/sda5 32 14593 116969233+ 83 Linux sda5 set in the installer as dm-crypted aes, contains an lvm volume group with two volumes, 3.5G swap in the end and a root volume in the beginning that fills the rest of the space. Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot: [O] Detect network card: [E] Configure network: [O] Detect CD: [O] Load installer modules: [O] Detect hard drives: [O] Partition hard drives: [E] Install base system: [O] Clock/timezone setup: [O] User/password setup: [O] Install tasks: [E] Install boot loader: [E] Overall install: [O] Comments/Problems: Network card detection fails: The correct driver is e1000, but a newer driver is needed than is in the etch kernel (or in the latest vanilla kernel tree, for that matter; it's a mere matter of an additional pci id in the driver source, though). Sources are available from http://e1000.sf.net/ , where I got them and built a module for the etch installer kernel. I put the module on an usb stick. I tried to load all modules offered by the installer, but apparently the floppy module failed to load (there is no floppy drive in this computer). After that, the installer prompted me to install the floppy module again and again, like in configuring disks or configuring network hardware(!). I failed with the netboot image initially because it lacked the usb-storage module, so I could not mount the usb stick and insmod the module from there. It's a bit hard to comprehend why it has the floppy module but not the usb-storage module, unless it's an unintentional omission. The installer offered to search for additional modules from floppies, but not from the USB stick, so I did it by hand in another vt. It was a straightforward mount, insmod, unmount. I managed to get the partitioner program to hang twice before, needing reboot (it just ended in a state with no choices and all the three buttons disabled). There was nothing special in dmesg or seemingly other logs, and in other vts everything worked fine. This happened while playing around with lvm+dm-crypt, but I couldn't reproduce it a third time while taking notes. I got the impression that it was the installer program that was in some perpetual wait state, anyway. I found one obvious way to bring the system into an incoherent state. It is possible to create a crypted partition and enable it, and after that to restart the partitioning process by choosing guided partitioning and no lvm. As a result the installer shows in the partitioning program a /boot partition (#1) and a / ext3 partition (#5), _and_ an sda5_crypt partition with free space. It appears the created crypt mappings were not reversed before restarting the partitioning. It also appears that there is no other way to go back in the partitioning process to before setting up the crypto. I was also initially slightly confused by the sda5_crypt partition. It looked like a disk where I could add multiple partitions, but after deleting the default 100 % partition and adding a swap partition to the end of sda5_crypt, the rest of the free space in sda5_crypt was "ususable". Actually it was this that prompted me to restart the partitioning process a couple of times, and I believe the installer hangs were related to this. While the tasks were being installed, I was doing stuff in the other vts, and was suddenly brought back to the main menu (vts were automatically switched, I think). The cursor was still positioned in the "install tasks" (or something) choice. I rechose that, and got some mysterious failures with no good explanation. Once there was even an error message, something like "Installation failed:", with nothing more on the line. By rechoosing the mirrors a couple of times and just retrying, I think I got it to succeed (at least to some extent). Boot loader installation (on MBR) initially failed. Again no good error message, it just told that it failed. It succeeded, however, on I think the first retry. I booted to a basically working system, however the configuration appears to be done halfway, for example /etc/X11/xorg.conf was _empty_. I got the feeling that the only issue really related to the specific hardware (this laptop) was the network card driver issue. Also I believe the broadcom wlan chip does not work in the installer (I have been told it needs ndiswrapper and the binary windows driver, so it can't probably be supported in a free way at all, and I have no problem with that). Now after having installed the system and done some configuration, everything except the wlan works just fine. -- Please make sure that the hardware-summary log file, and any other installation logs that you think would be useful are attached to this report. Please compress large files using gzip. Once you have filled out this report, mail it to submit@bugs.debian.org. ============================================== Installer lsb-release: ============================================== DISTRIB_ID=Debian DISTRIB_DESCRIPTION="Debian GNU/Linux installer" DISTRIB_RELEASE="4.0 (installer build 20070308etch1)" X_INSTALLATION_MEDIUM=cdrom ============================================== Installer hardware-summary: ============================================== umame -a: Linux lap 2.6.18-5-amd64 #1 SMP Thu May 31 23:51:05 UTC 2007 x86_64 unknown lspci -nn: 00:00.0 Host bridge [0600]: Intel Corporation Mobile Memory Controller Hub [8086:2a00] (rev 0c) lspci -nn: 00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile Integrated Graphics Controller [8086:2a02] (rev 0c) lspci -nn: 00:02.1 Display controller [0380]: Intel Corporation Mobile Integrated Graphics Controller [8086:2a03] (rev 0c) lspci -nn: 00:19.0 Ethernet controller [0200]: Intel Corporation Unknown device [8086:10c4] (rev 03) lspci -nn: 00:1a.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI #4 [8086:2834] (rev 03) lspci -nn: 00:1a.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI #2 [8086:283a] (rev 03) lspci -nn: 00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio Controller [8086:284b] (rev 03) lspci -nn: 00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 [8086:283f] (rev 03) lspci -nn: 00:1c.1 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 [8086:2841] (rev 03) lspci -nn: 00:1c.4 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 [8086:2847] (rev 03) lspci -nn: 00:1d.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI #1 [8086:2830] (rev 03) lspci -nn: 00:1d.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI #2 [8086:2831] (rev 03) lspci -nn: 00:1d.2 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI #3 [8086:2832] (rev 03) lspci -nn: 00:1d.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI #1 [8086:2836] (rev 03) lspci -nn: 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev f3) lspci -nn: 00:1f.0 ISA bridge [0601]: Intel Corporation Mobile LPC Interface Controller [8086:2815] (rev 03) lspci -nn: 00:1f.1 IDE interface [0101]: Intel Corporation Mobile IDE Controller [8086:2850] (rev 03) lspci -nn: 00:1f.2 SATA controller [0106]: Intel Corporation Mobile SATA AHCI Controller [8086:2829] (rev 03) lspci -nn: 10:00.0 Network controller [0280]: Broadcom Corporation Dell Wireless 1390 WLAN Mini-PCI Card [14e4:4311] (rev 02) lspci -vnn: 00:00.0 Host bridge [0600]: Intel Corporation Mobile Memory Controller Hub [8086:2a00] (rev 0c) lspci -vnn: Subsystem: Hewlett-Packard Company Unknown device [103c:30d8] lspci -vnn: Flags: bus master, fast devsel, latency 0 lspci -vnn: Capabilities: [e0] Vendor Specific Information lspci -vnn: lspci -vnn: 00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile Integrated Graphics Controller [8086:2a02] (rev 0c) lspci -vnn: Subsystem: Hewlett-Packard Company Unknown device [103c:30d8] lspci -vnn: Flags: fast devsel, IRQ 10 lspci -vnn: Memory at e4400000 (64-bit, non-prefetchable) [size=1M] lspci -vnn: Memory at d0000000 (64-bit, prefetchable) [size=256M] lspci -vnn: I/O ports at 4000 [size=8] lspci -vnn: Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- lspci -vnn: Capabilities: [d0] Power Management version 3 lspci -vnn: lspci -vnn: 00:02.1 Display controller [0380]: Intel Corporation Mobile Integrated Graphics Controller [8086:2a03] (rev 0c) lspci -vnn: Subsystem: Hewlett-Packard Company Unknown device [103c:30d8] lspci -vnn: Flags: bus master, fast devsel, latency 0 lspci -vnn: Memory at e4500000 (64-bit, non-prefetchable) [size=1M] lspci -vnn: Capabilities: [d0] Power Management version 3 lspci -vnn: lspci -vnn: 00:19.0 Ethernet controller [0200]: Intel Corporation Unknown device [8086:10c4] (rev 03) lspci -vnn: Subsystem: Hewlett-Packard Company Unknown device [103c:30d8] lspci -vnn: Flags: bus master, fast devsel, latency 0, IRQ 66 lspci -vnn: Memory at e4600000 (32-bit, non-prefetchable) [size=128K] lspci -vnn: Memory at e4620000 (32-bit, non-prefetchable) [size=4K] lspci -vnn: I/O ports at 4020 [size=32] lspci -vnn: Capabilities: [c8] Power Management version 2 lspci -vnn: Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+ lspci -vnn: lspci -vnn: 00:1a.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI #4 [8086:2834] (rev 03) lspci -vnn: Subsystem: Hewlett-Packard Company Unknown device [103c:30d8] lspci -vnn: Flags: bus master, medium devsel, latency 0, IRQ 169 lspci -vnn: I/O ports at 4040 [size=32] lspci -vnn: lspci -vnn: 00:1a.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI #2 [8086:283a] (rev 03) (prog-if 20) lspci -vnn: Subsystem: Hewlett-Packard Company Unknown device [103c:30d8] lspci -vnn: Flags: bus master, medium devsel, latency 0, IRQ 217 lspci -vnn: Memory at e4621000 (32-bit, non-prefetchable) [size=1K] lspci -vnn: Capabilities: [50] Power Management version 2 lspci -vnn: Capabilities: [58] Debug port lspci -vnn: lspci -vnn: 00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio Controller [8086:284b] (rev 03) lspci -vnn: Subsystem: Hewlett-Packard Company Unknown device [103c:30d8] lspci -vnn: Flags: bus master, fast devsel, latency 0, IRQ 10 lspci -vnn: Memory at e4624000 (64-bit, non-prefetchable) [size=16K] lspci -vnn: Capabilities: [50] Power Management version 2 lspci -vnn: Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- lspci -vnn: Capabilities: [70] Express Unknown type IRQ 0 lspci -vnn: lspci -vnn: 00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 [8086:283f] (rev 03) lspci -vnn: Flags: bus master, fast devsel, latency 0 lspci -vnn: Bus: primary=00, secondary=08, subordinate=08, sec-latency=0 lspci -vnn: Capabilities: [40] Express Root Port (Slot-) IRQ 0 lspci -vnn: Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ lspci -vnn: Capabilities: [90] Subsystem: Hewlett-Packard Company Unknown device [103c:30d8] lspci -vnn: Capabilities: [a0] Power Management version 2 lspci -vnn: lspci -vnn: 00:1c.1 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 [8086:2841] (rev 03) lspci -vnn: Flags: bus master, fast devsel, latency 0 lspci -vnn: Bus: primary=00, secondary=10, subordinate=10, sec-latency=0 lspci -vnn: Memory behind bridge: e4000000-e40fffff lspci -vnn: Capabilities: [40] Express Root Port (Slot+) IRQ 0 lspci -vnn: Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ lspci -vnn: Capabilities: [90] Subsystem: Hewlett-Packard Company Unknown device [103c:30d8] lspci -vnn: Capabilities: [a0] Power Management version 2 lspci -vnn: lspci -vnn: 00:1c.4 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 [8086:2847] (rev 03) lspci -vnn: Flags: bus master, fast devsel, latency 0 lspci -vnn: Bus: primary=00, secondary=28, subordinate=28, sec-latency=0 lspci -vnn: I/O behind bridge: 00002000-00003fff lspci -vnn: Memory behind bridge: e0000000-e3ffffff lspci -vnn: Capabilities: [40] Express Root Port (Slot+) IRQ 0 lspci -vnn: Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ lspci -vnn: Capabilities: [90] Subsystem: Hewlett-Packard Company Unknown device [103c:30d8] lspci -vnn: Capabilities: [a0] Power Management version 2 lspci -vnn: lspci -vnn: 00:1d.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI #1 [8086:2830] (rev 03) lspci -vnn: Subsystem: Hewlett-Packard Company Unknown device [103c:30d8] lspci -vnn: Flags: bus master, medium devsel, latency 0, IRQ 225 lspci -vnn: I/O ports at 4060 [size=32] lspci -vnn: lspci -vnn: 00:1d.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI #2 [8086:2831] (rev 03) lspci -vnn: Subsystem: Hewlett-Packard Company Unknown device [103c:30d8] lspci -vnn: Flags: bus master, medium devsel, latency 0, IRQ 233 lspci -vnn: I/O ports at 4080 [size=32] lspci -vnn: lspci -vnn: 00:1d.2 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI #3 [8086:2832] (rev 03) lspci -vnn: Subsystem: Hewlett-Packard Company Unknown device [103c:30d8] lspci -vnn: Flags: bus master, medium devsel, latency 0, IRQ 217 lspci -vnn: I/O ports at 40a0 [size=32] lspci -vnn: lspci -vnn: 00:1d.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI #1 [8086:2836] (rev 03) (prog-if 20) lspci -vnn: Subsystem: Hewlett-Packard Company Unknown device [103c:30d8] lspci -vnn: Flags: bus master, medium devsel, latency 0, IRQ 225 lspci -vnn: Memory at e4628000 (32-bit, non-prefetchable) [size=1K] lspci -vnn: Capabilities: [50] Power Management version 2 lspci -vnn: Capabilities: [58] Debug port lspci -vnn: lspci -vnn: 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev f3) (prog-if 01) lspci -vnn: Flags: bus master, fast devsel, latency 0 lspci -vnn: Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 lspci -vnn: Capabilities: [50] Subsystem: Hewlett-Packard Company Unknown device [103c:30d8] lspci -vnn: lspci -vnn: 00:1f.0 ISA bridge [0601]: Intel Corporation Mobile LPC Interface Controller [8086:2815] (rev 03) lspci -vnn: Subsystem: Hewlett-Packard Company Unknown device [103c:30d8] lspci -vnn: Flags: bus master, medium devsel, latency 0 lspci -vnn: Capabilities: [e0] Vendor Specific Information lspci -vnn: lspci -vnn: 00:1f.1 IDE interface [0101]: Intel Corporation Mobile IDE Controller [8086:2850] (rev 03) (prog-if 8a [Master SecP PriP]) lspci -vnn: Subsystem: Hewlett-Packard Company Unknown device [103c:30d8] lspci -vnn: Flags: bus master, medium devsel, latency 0, IRQ 169 lspci -vnn: I/O ports at <unassigned> lspci -vnn: I/O ports at <unassigned> lspci -vnn: I/O ports at <unassigned> lspci -vnn: I/O ports at <unassigned> lspci -vnn: I/O ports at 40c0 [size=16] lspci -vnn: lspci -vnn: 00:1f.2 SATA controller [0106]: Intel Corporation Mobile SATA AHCI Controller [8086:2829] (rev 03) (prog-if 01) lspci -vnn: Subsystem: Hewlett-Packard Company Unknown device [103c:30d8] lspci -vnn: Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 50 lspci -vnn: I/O ports at 13f0 [size=8] lspci -vnn: I/O ports at 15f4 [size=4] lspci -vnn: I/O ports at 1370 [size=8] lspci -vnn: I/O ports at 1574 [size=4] lspci -vnn: I/O ports at 4100 [size=32] lspci -vnn: Memory at e4629000 (32-bit, non-prefetchable) [size=2K] lspci -vnn: Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/2 Enable+ lspci -vnn: Capabilities: [70] Power Management version 3 lspci -vnn: Capabilities: [a8] #12 [0010] lspci -vnn: lspci -vnn: 10:00.0 Network controller [0280]: Broadcom Corporation Dell Wireless 1390 WLAN Mini-PCI Card [14e4:4311] (rev 02) lspci -vnn: Subsystem: Hewlett-Packard Company Unknown device [103c:1375] lspci -vnn: Flags: bus master, fast devsel, latency 0, IRQ 10 lspci -vnn: Memory at e4000000 (64-bit, non-prefetchable) [size=16K] lspci -vnn: Capabilities: [40] Power Management version 3 lspci -vnn: Capabilities: [58] Vendor Specific Information lspci -vnn: Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- lspci -vnn: Capabilities: [d0] Express Endpoint IRQ 0 lspci -vnn: modulemap: 8086:10c4 e1000 modulemap: 8086:2834 uhci_hcd modulemap: 8086:283a ehci_hcd modulemap: 8086:2830 uhci_hcd modulemap: 8086:2831 uhci_hcd modulemap: 8086:2832 uhci_hcd modulemap: 8086:2836 ehci_hcd modulemap: 8086:2850 piix modulemap: 8086:2829 ahci lsmod: Module Size Used by lsmod: qnx4 16840 0 lsmod: ntfs 190728 0 lsmod: sha256 13312 0 lsmod: aes 31040 2 lsmod: dm_crypt 16400 1 lsmod: dm_mod 62800 8 dm_crypt lsmod: xfs 485192 0 lsmod: reiserfs 231168 0 lsmod: jfs 166992 0 lsmod: ext3 138512 2 lsmod: jbd 65392 1 ext3 lsmod: ext2 70416 0 lsmod: mbcache 14216 2 ext3,ext2 lsmod: e1000 213312 0 lsmod: nls_cp437 11264 0 lsmod: vfat 17792 0 lsmod: fat 55984 1 vfat lsmod: nls_iso8859_1 9472 0 lsmod: isofs 39396 0 lsmod: ide_disk 20352 0 lsmod: ide_generic 5632 0 [permanent] lsmod: pdc202xx_new 13312 0 [permanent] lsmod: triflex 8448 0 [permanent] lsmod: pdc202xx_old 14848 0 [permanent] lsmod: amd74xx 19248 0 [permanent] lsmod: cs5530 9984 0 [permanent] lsmod: sis5513 18192 0 [permanent] lsmod: cy82c693 9096 0 [permanent] lsmod: ns87415 8904 0 [permanent] lsmod: serverworks 13456 0 [permanent] lsmod: alim15x3 16152 0 [permanent] lsmod: cmd64x 15308 0 [permanent] lsmod: via82cxxx 13188 0 [permanent] lsmod: atiixp 11024 0 [permanent] lsmod: jmicron 9088 0 [permanent] lsmod: slc90e66 10112 0 [permanent] lsmod: sc1200 11520 0 [permanent] lsmod: hpt34x 9856 0 [permanent] lsmod: rz1000 7296 0 [permanent] lsmod: cs5520 9472 0 [permanent] lsmod: it821x 12932 0 [permanent] lsmod: siimage 16640 0 [permanent] lsmod: aec62xx 12288 0 [permanent] lsmod: opti621 9220 0 [permanent] lsmod: trm290 8836 0 [permanent] lsmod: usb_storage 86848 0 lsmod: usbmouse 10240 0 lsmod: vga16fb 16280 0 lsmod: vgastate 12416 1 vga16fb lsmod: usbserial 38640 0 lsmod: usbhid 44704 0 lsmod: usbkbd 11776 0 lsmod: thermal 19984 0 lsmod: processor 37608 1 thermal lsmod: fan 9608 0 lsmod: ide_cd 44704 0 lsmod: cdrom 40104 1 ide_cd lsmod: generic 10244 0 [permanent] lsmod: sd_mod 25600 3 lsmod: psmouse 43920 0 lsmod: piix 15236 0 [permanent] lsmod: ahci 24324 2 lsmod: libata 106272 1 ahci lsmod: scsi_mod 151984 4 usb_storage,sd_mod,ahci,libata lsmod: ide_core 146816 30 ide_disk,ide_generic,pdc202xx_new,triflex,pdc202xx_old,amd74xx,cs5530,sis5513,cy82c693,ns87415,serverworks,alim15x3,cmd64x,via82cxxx,atiixp,jmicron,slc90e66,sc1200,hpt34x,rz1000,cs5520,it821x,siimage,aec62xx,opti621,trm290,usb_storage,ide_cd,generic,piix lsmod: uhci_hcd 28312 0 lsmod: ehci_hcd 35720 0 lsmod: evdev 14976 4 df: Filesystem 1k-blocks Used Available Use% Mounted on df: tmpfs 1026540 420 1026120 0% /dev df: tmpfs 1026540 420 1026120 0% /dev df: tmpfs 1026540 420 1026120 0% /.dev df: /dev/mapper/rootvg-root--volume 111516440 3208952 107174536 3% /target df: /dev/scsi/host0/bus0/target0/lun0/part1 241116 20750 207918 9% /target/boot free: total used free shared buffers free: Mem: 2053080 1956576 96504 0 88752 free: Swap: 3670008 8 3670000 free: Total: 5723088 1956584 3766504 cardctl status: /usr/bin/report-hw: /usr/bin/report-hw: 50: cardctl: not found cardctl ident: /usr/bin/report-hw: /usr/bin/report-hw: 51: cardctl: not found /proc/cpuinfo: processor : 0 /proc/cpuinfo: vendor_id : GenuineIntel /proc/cpuinfo: cpu family : 6 /proc/cpuinfo: model : 15 /proc/cpuinfo: model name : Intel(R) Celeron(R) M CPU 530 @ 1.73GHz /proc/cpuinfo: stepping : 10 /proc/cpuinfo: cpu MHz : 1729.004 /proc/cpuinfo: cache size : 1024 KB /proc/cpuinfo: fpu : yes /proc/cpuinfo: fpu_exception : yes /proc/cpuinfo: cpuid level : 10 /proc/cpuinfo: wp : yes /proc/cpuinfo: flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss tm syscall nx lm constant_tsc up pni monitor ds_cpl tm2 cx16 xtpr lahf_lm /proc/cpuinfo: bogomips : 3463.33 /proc/cpuinfo: clflush size : 64 /proc/cpuinfo: cache_alignment : 64 /proc/cpuinfo: address sizes : 36 bits physical, 48 bits virtual /proc/cpuinfo: power management: /proc/cpuinfo: /proc/ioports: 0000-001f : dma1 /proc/ioports: 0020-0021 : pic1 /proc/ioports: 0040-0043 : timer0 /proc/ioports: 0050-0053 : timer1 /proc/ioports: 0060-006f : keyboard /proc/ioports: 0070-0077 : rtc /proc/ioports: 0080-008f : dma page reg /proc/ioports: 00a0-00a1 : pic2 /proc/ioports: 00c0-00df : dma2 /proc/ioports: 00f0-00ff : fpu /proc/ioports: 01f0-01f7 : ide0 /proc/ioports: 03c0-03df : vesafb /proc/ioports: 03f6-03f6 : ide0 /proc/ioports: 04d0-04d1 : pnp 00:0a /proc/ioports: 0cf8-0cff : PCI conf1 /proc/ioports: 1000-107f : motherboard /proc/ioports: 1000-1003 : ACPI PM1a_EVT_BLK /proc/ioports: 1004-1005 : ACPI PM1a_CNT_BLK /proc/ioports: 1008-100b : ACPI PM_TMR /proc/ioports: 1010-1015 : ACPI CPU throttle /proc/ioports: 1020-1020 : ACPI PM2_CNT_BLK /proc/ioports: 1028-102f : ACPI GPE0_BLK /proc/ioports: 1100-113f : motherboard /proc/ioports: 1100-113f : pnp 00:0a /proc/ioports: 1200-121f : motherboard /proc/ioports: 1200-121f : pnp 00:0a /proc/ioports: 1370-1377 : 0000:00:1f.2 /proc/ioports: 1370-1377 : ahci /proc/ioports: 13f0-13f7 : 0000:00:1f.2 /proc/ioports: 13f0-13f7 : ahci /proc/ioports: 1574-1577 : 0000:00:1f.2 /proc/ioports: 1574-1577 : ahci /proc/ioports: 15f4-15f7 : 0000:00:1f.2 /proc/ioports: 15f4-15f7 : ahci /proc/ioports: 2000-3fff : PCI Bus #28 /proc/ioports: 4000-4007 : 0000:00:02.0 /proc/ioports: 4020-403f : 0000:00:19.0 /proc/ioports: 4020-403f : e1000 /proc/ioports: 4040-405f : 0000:00:1a.0 /proc/ioports: 4040-405f : uhci_hcd /proc/ioports: 4060-407f : 0000:00:1d.0 /proc/ioports: 4060-407f : uhci_hcd /proc/ioports: 4080-409f : 0000:00:1d.1 /proc/ioports: 4080-409f : uhci_hcd /proc/ioports: 40a0-40bf : 0000:00:1d.2 /proc/ioports: 40a0-40bf : uhci_hcd /proc/ioports: 40c0-40cf : 0000:00:1f.1 /proc/ioports: 40c0-40c7 : ide0 /proc/ioports: 4100-411f : 0000:00:1f.2 /proc/ioports: 4100-411f : ahci /proc/iomem: 00000000-0009fbff : System RAM /proc/iomem: 00000000-00000000 : Crash kernel /proc/iomem: 0009fc00-0009ffff : reserved /proc/iomem: 000a0000-000bffff : Video RAM area /proc/iomem: 000c0000-000c7fff : Video ROM /proc/iomem: 000d0000-000d0fff : Adapter ROM /proc/iomem: 000d1000-000d1fff : Adapter ROM /proc/iomem: 000f0000-000fffff : System ROM /proc/iomem: 00100000-7f7affff : System RAM /proc/iomem: 00200000-003e1ed2 : Kernel code /proc/iomem: 003e1ed3-004bb04f : Kernel data /proc/iomem: 7f7b0000-7f7c53ff : reserved /proc/iomem: 7f7c5400-7f7e7fb7 : ACPI Non-volatile Storage /proc/iomem: 7f7e7fb8-7fffffff : reserved /proc/iomem: d0000000-dfffffff : 0000:00:02.0 /proc/iomem: d0000000-d076ffff : vesafb /proc/iomem: e0000000-e3ffffff : PCI Bus #28 /proc/iomem: e4000000-e40fffff : PCI Bus #10 /proc/iomem: e4000000-e4003fff : 0000:10:00.0 /proc/iomem: e4400000-e44fffff : 0000:00:02.0 /proc/iomem: e4500000-e45fffff : 0000:00:02.1 /proc/iomem: e4600000-e461ffff : 0000:00:19.0 /proc/iomem: e4600000-e461ffff : e1000 /proc/iomem: e4620000-e4620fff : 0000:00:19.0 /proc/iomem: e4620000-e4620fff : e1000 /proc/iomem: e4621000-e46213ff : 0000:00:1a.7 /proc/iomem: e4621000-e46213ff : ehci_hcd /proc/iomem: e4624000-e4627fff : 0000:00:1b.0 /proc/iomem: e4628000-e46283ff : 0000:00:1d.7 /proc/iomem: e4628000-e46283ff : ehci_hcd /proc/iomem: e4629000-e46297ff : 0000:00:1f.2 /proc/iomem: e4629000-e46297ff : ahci /proc/iomem: fec00000-fec00fff : reserved /proc/iomem: fed20000-fed99fff : reserved /proc/iomem: feda0000-fedbffff : reserved /proc/iomem: fee00000-fee00fff : reserved /proc/iomem: ffb00000-ffbfffff : reserved /proc/iomem: fff00000-ffffffff : reserved /proc/interrupts: CPU0 /proc/interrupts: 0: 584368 IO-APIC-edge timer /proc/interrupts: 1: 3639 IO-APIC-edge i8042 /proc/interrupts: 8: 1 IO-APIC-edge rtc /proc/interrupts: 9: 59 IO-APIC-level acpi /proc/interrupts: 12: 7728 IO-APIC-edge i8042 /proc/interrupts: 14: 2397 IO-APIC-edge ide0 /proc/interrupts: 50: 140262 PCI-MSI libata /proc/interrupts: 66: 259186 PCI-MSI eth0 /proc/interrupts: 169: 0 IO-APIC-level uhci_hcd:usb3 /proc/interrupts: 217: 0 IO-APIC-level ehci_hcd:usb1, uhci_hcd:usb6 /proc/interrupts: 225: 2 IO-APIC-level ehci_hcd:usb2, uhci_hcd:usb4 /proc/interrupts: 233: 625 IO-APIC-level uhci_hcd:usb5 /proc/interrupts: NMI: 726 /proc/interrupts: LOC: 584327 /proc/interrupts: ERR: 0 /proc/interrupts: MIS: 0 /proc/meminfo: MemTotal: 2053080 kB /proc/meminfo: MemFree: 96464 kB /proc/meminfo: Buffers: 88752 kB /proc/meminfo: Cached: 1673592 kB /proc/meminfo: SwapCached: 0 kB /proc/meminfo: Active: 902548 kB /proc/meminfo: Inactive: 885664 kB /proc/meminfo: HighTotal: 0 kB /proc/meminfo: HighFree: 0 kB /proc/meminfo: LowTotal: 2053080 kB /proc/meminfo: LowFree: 96464 kB /proc/meminfo: SwapTotal: 3670008 kB /proc/meminfo: SwapFree: 3670000 kB /proc/meminfo: Dirty: 2180 kB /proc/meminfo: Writeback: 0 kB /proc/meminfo: AnonPages: 25868 kB /proc/meminfo: Mapped: 7656 kB /proc/meminfo: Slab: 148388 kB /proc/meminfo: PageTables: 524 kB /proc/meminfo: NFS_Unstable: 0 kB /proc/meminfo: Bounce: 0 kB /proc/meminfo: CommitLimit: 4696548 kB /proc/meminfo: Committed_AS: 73820 kB /proc/meminfo: VmallocTotal: 34359738367 kB /proc/meminfo: VmallocUsed: 10056 kB /proc/meminfo: VmallocChunk: 34359727983 kB /proc/bus/input/devices: I: Bus=0011 Vendor=0001 Product=0001 Version=ab41 /proc/bus/input/devices: N: Name="AT Translated Set 2 keyboard" /proc/bus/input/devices: P: Phys=isa0060/serio0/input0 /proc/bus/input/devices: S: Sysfs=/class/input/input0 /proc/bus/input/devices: H: Handlers=kbd event0 /proc/bus/input/devices: B: EV=120013 /proc/bus/input/devices: B: KEY=402000000 3802078f840d001 feffffdfffefffff fffffffffffffffe /proc/bus/input/devices: B: MSC=10 /proc/bus/input/devices: B: LED=7 /proc/bus/input/devices: /proc/bus/input/devices: I: Bus=0011 Vendor=0002 Product=0007 Version=0000 /proc/bus/input/devices: N: Name="SynPS/2 Synaptics TouchPad" /proc/bus/input/devices: P: Phys=isa0060/serio4/input0 /proc/bus/input/devices: S: Sysfs=/class/input/input1 /proc/bus/input/devices: H: Handlers=mouse0 event1 /proc/bus/input/devices: B: EV=b /proc/bus/input/devices: B: KEY=6420 70000 0 0 0 0 /proc/bus/input/devices: B: ABS=11000003 /proc/bus/input/devices: dmidecode: # dmidecode 2.8 dmidecode: SMBIOS 2.4 present. dmidecode: 25 structures occupying 1236 bytes. dmidecode: Table at 0x000F25A0. dmidecode: dmidecode: Handle 0x0000, DMI type 0, 24 bytes dmidecode: BIOS Information dmidecode: Vendor: Hewlett-Packard dmidecode: Version: 68MDU Ver. F.07 dmidecode: Release Date: 11/20/2007 dmidecode: Address: 0xE0000 dmidecode: Runtime Size: 128 kB dmidecode: ROM Size: 1024 kB dmidecode: Characteristics: dmidecode: PCI is supported dmidecode: PC Card (PCMCIA) is supported dmidecode: PNP is supported dmidecode: BIOS is upgradeable dmidecode: BIOS shadowing is allowed dmidecode: Boot from CD is supported dmidecode: Selectable boot is supported dmidecode: EDD is supported dmidecode: 3.5"/720 KB floppy services are supported (int 13h) dmidecode: Print screen service is supported (int 5h) dmidecode: 8042 keyboard services are supported (int 9h) dmidecode: Serial services are supported (int 14h) dmidecode: Printer services are supported (int 17h) dmidecode: ACPI is supported dmidecode: USB legacy is supported dmidecode: LS-120 boot is supported dmidecode: Smart battery is supported dmidecode: BIOS boot specification is supported dmidecode: Function key-initiated network boot is supported dmidecode: Targeted content distribution is supported dmidecode: BIOS Revision: 15.7 dmidecode: Firmware Revision: 131.14 dmidecode: dmidecode: Handle 0x0001, DMI type 1, 27 bytes dmidecode: System Information dmidecode: Manufacturer: Hewlett-Packard dmidecode: Product Name: HP Compaq 6720s dmidecode: Version: F.07 dmidecode: Serial Number: CNU7480RZK dmidecode: UUID: E641E10F-9F15-E011-18A0-6D990E4FCD29 dmidecode: Wake-up Type: Power Switch dmidecode: SKU Number: GB901ET#AK8 dmidecode: Family: 103C_5336AN dmidecode: dmidecode: Handle 0x0040, DMI type 126, 48 bytes dmidecode: Inactive dmidecode: dmidecode: Handle 0x0002, DMI type 2, 8 bytes dmidecode: Base Board Information dmidecode: Manufacturer: Hewlett-Packard dmidecode: Product Name: 30D8 dmidecode: Version: KBC Version 83.0E dmidecode: Serial Number: Not Specified dmidecode: dmidecode: Handle 0x0003, DMI type 3, 13 bytes dmidecode: Chassis Information dmidecode: Manufacturer: Hewlett-Packard dmidecode: Type: Notebook dmidecode: Lock: Not Present dmidecode: Version: Not Specified dmidecode: Serial Number: CNU7480RZK dmidecode: Asset Tag: CNU7480RZK dmidecode: Boot-up State: Safe dmidecode: Power Supply State: Safe dmidecode: Thermal State: Safe dmidecode: Security Status: External Interface Enabled dmidecode: dmidecode: Handle 0x0041, DMI type 126, 32 bytes dmidecode: Inactive dmidecode: dmidecode: Handle 0x0004, DMI type 4, 35 bytes dmidecode: Processor Information dmidecode: Socket Designation: U10 dmidecode: Type: Central Processor dmidecode: Family: Pentium M dmidecode: Manufacturer: Intel(R) dmidecode: ID: FA 06 00 00 FF FB EB AF dmidecode: Signature: Type 0, Family 6, Model 15, Stepping 10 dmidecode: Flags: dmidecode: FPU (Floating-point unit on-chip) dmidecode: VME (Virtual mode extension) dmidecode: DE (Debugging extension) dmidecode: PSE (Page size extension) dmidecode: TSC (Time stamp counter) dmidecode: MSR (Model specific registers) dmidecode: PAE (Physical address extension) dmidecode: MCE (Machine check exception) dmidecode: CX8 (CMPXCHG8 instruction supported) dmidecode: APIC (On-chip APIC hardware supported) dmidecode: SEP (Fast system call) dmidecode: MTRR (Memory type range registers) dmidecode: PGE (Page global enable) dmidecode: MCA (Machine check architecture) dmidecode: CMOV (Conditional move instruction supported) dmidecode: PAT (Page attribute table) dmidecode: PSE-36 (36-bit page size extension) dmidecode: CLFSH (CLFLUSH instruction supported) dmidecode: DS (Debug store) dmidecode: ACPI (ACPI supported) dmidecode: MMX (MMX technology supported) dmidecode: FXSR (Fast floating-point save and restore) dmidecode: SSE (Streaming SIMD extensions) dmidecode: SSE2 (Streaming SIMD extensions 2) dmidecode: SS (Self-snoop) dmidecode: TM (Thermal monitor supported) dmidecode: PBE (Pending break enabled) dmidecode: Version: Intel(R) Celeron(R) M CPU 530 @ 1.73GHz dmidecode: Voltage: 1.1 V dmidecode: External Clock: 133 MHz dmidecode: Max Speed: 1733 MHz dmidecode: Current Speed: 1733 MHz dmidecode: Status: Populated, Enabled dmidecode: Upgrade: None dmidecode: L1 Cache Handle: 0x0005 dmidecode: L2 Cache Handle: 0x0006 dmidecode: L3 Cache Handle: Not Provided dmidecode: Serial Number: Not Specified dmidecode: Asset Tag: Not Specified dmidecode: Part Number: Not Specified dmidecode: dmidecode: Handle 0x0005, DMI type 7, 19 bytes dmidecode: Cache Information dmidecode: Socket Designation: Internal L1 Cache dmidecode: Configuration: Enabled, Not Socketed, Level 1 dmidecode: Operational Mode: Write Back dmidecode: Location: Internal dmidecode: Installed Size: 64 KB dmidecode: Maximum Size: 64 KB dmidecode: Supported SRAM Types: dmidecode: Burst dmidecode: Installed SRAM Type: Burst dmidecode: Speed: Unknown dmidecode: Error Correction Type: Unknown dmidecode: System Type: Unified dmidecode: Associativity: 4-way Set-associative dmidecode: dmidecode: Handle 0x0006, DMI type 7, 19 bytes dmidecode: Cache Information dmidecode: Socket Designation: Internal L2 Cache dmidecode: Configuration: Enabled, Not Socketed, Level 2 dmidecode: Operational Mode: Write Back dmidecode: Location: External dmidecode: Installed Size: 1024 KB dmidecode: Maximum Size: 1024 KB dmidecode: Supported SRAM Types: dmidecode: Burst dmidecode: Installed SRAM Type: Burst dmidecode: Speed: Unknown dmidecode: Error Correction Type: None dmidecode: System Type: Unified dmidecode: Associativity: 4-way Set-associative dmidecode: dmidecode: Handle 0x0007, DMI type 9, 13 bytes dmidecode: System Slot Information dmidecode: Designation: PC CARD-Slot 0 dmidecode: Type: 32-bit PC Card (PCMCIA) dmidecode: Current Usage: Available dmidecode: Length: Short dmidecode: ID: Adapter 0, Socket 0 dmidecode: Characteristics: dmidecode: 5.0 V is provided dmidecode: 3.3 V is provided dmidecode: PC Card-16 is supported dmidecode: Cardbus is supported dmidecode: PME signal is supported dmidecode: dmidecode: Handle 0x0008, DMI type 10, 6 bytes dmidecode: On Board Device Information dmidecode: Type: Video dmidecode: Status: Enabled dmidecode: Description: 8 dmidecode: dmidecode: Handle 0x0009, DMI type 11, 5 bytes dmidecode: OEM Strings dmidecode: String 1: www.hp.com dmidecode: String 2: ABS 70/71 79 7A 7B 7C dmidecode: dmidecode: Handle 0x000A, DMI type 16, 15 bytes dmidecode: Physical Memory Array dmidecode: Location: System Board Or Motherboard dmidecode: Use: System Memory dmidecode: Error Correction Type: None dmidecode: Maximum Capacity: 4 GB dmidecode: Error Information Handle: No Error dmidecode: Number Of Devices: 2 dmidecode: dmidecode: Handle 0x000B, DMI type 17, 27 bytes dmidecode: Memory Device dmidecode: Array Handle: 0x000A dmidecode: Error Information Handle: No Error dmidecode: Total Width: 64 bits dmidecode: Data Width: 64 bits dmidecode: Size: 1024 MB dmidecode: Form Factor: SODIMM dmidecode: Set: None dmidecode: Locator: DIMM #1 dmidecode: Bank Locator: Not Specified dmidecode: Type: DDR2 dmidecode: Type Detail: Synchronous dmidecode: Speed: 667 MHz (1.5 ns) dmidecode: Manufacturer: Qimonda dmidecode: Serial Number: 16021E20 dmidecode: Asset Tag: Not Specified dmidecode: Part Number: 64T128021HDL3SB dmidecode: dmidecode: Handle 0x000C, DMI type 17, 27 bytes dmidecode: Memory Device dmidecode: Array Handle: 0x000A dmidecode: Error Information Handle: No Error dmidecode: Total Width: 64 bits dmidecode: Data Width: 64 bits dmidecode: Size: 1024 MB dmidecode: Form Factor: SODIMM dmidecode: Set: None dmidecode: Locator: DIMM #2 dmidecode: Bank Locator: Not Specified dmidecode: Type: DDR2 dmidecode: Type Detail: Synchronous dmidecode: Speed: 667 MHz (1.5 ns) dmidecode: Manufacturer: Qimonda dmidecode: Serial Number: 0908B220 dmidecode: Asset Tag: Not Specified dmidecode: Part Number: 64T128021EDL3SB2 dmidecode: dmidecode: Handle 0x000D, DMI type 19, 15 bytes dmidecode: Memory Array Mapped Address dmidecode: Starting Address: 0x00000000000 dmidecode: Ending Address: 0x0007FFFFFFF dmidecode: Range Size: 2 GB dmidecode: Physical Array Handle: 0x000A dmidecode: Partition Width: 0 dmidecode: dmidecode: Handle 0x000E, DMI type 20, 19 bytes dmidecode: Memory Device Mapped Address dmidecode: Starting Address: 0x00000000000 dmidecode: Ending Address: 0x0003FFFFFFF dmidecode: Range Size: 1 GB dmidecode: Physical Device Handle: 0x000B dmidecode: Memory Array Mapped Address Handle: 0x000D dmidecode: Partition Row Position: 1 dmidecode: dmidecode: Handle 0x000F, DMI type 20, 19 bytes dmidecode: Memory Device Mapped Address dmidecode: Starting Address: 0x00040000000 dmidecode: Ending Address: 0x0007FFFFFFF dmidecode: Range Size: 1 GB dmidecode: Physical Device Handle: 0x000C dmidecode: Memory Array Mapped Address Handle: 0x000D dmidecode: Partition Row Position: 2 dmidecode: dmidecode: Handle 0x0010, DMI type 22, 26 bytes dmidecode: Portable Battery dmidecode: Location: Primary dmidecode: Manufacturer: Hewlett-Packard dmidecode: Manufacture Date: 11/16/2007 dmidecode: Serial Number: 02717 dmidecode: Name: HP dmidecode: Chemistry: Lithium Ion dmidecode: Design Capacity: 44000 mWh dmidecode: Design Voltage: 10800 mV dmidecode: SBDS Version: Not Specified dmidecode: Maximum Error: Unknown dmidecode: OEM-specific Information: 0x00000000 dmidecode: dmidecode: Handle 0x0011, DMI type 126, 26 bytes dmidecode: Inactive dmidecode: dmidecode: Handle 0x0012, DMI type 32, 11 bytes dmidecode: System Boot Information dmidecode: Status: No errors detected dmidecode: dmidecode: Handle 0x0085, DMI type 133, 34 bytes dmidecode: OEM-specific Type dmidecode: Header and Data: dmidecode: 85 22 85 00 01 00 00 00 00 00 00 00 00 00 00 00 dmidecode: 00 00 00 00 00 00 00 02 00 00 00 00 00 00 00 00 dmidecode: 00 00 dmidecode: Strings: dmidecode: dmidecode: No battery dmidecode: dmidecode: Handle 0x0086, DMI type 134, 34 bytes dmidecode: OEM-specific Type dmidecode: Header and Data: dmidecode: 86 22 86 00 01 00 00 00 00 00 00 00 00 00 00 00 dmidecode: 00 00 00 00 00 00 00 02 00 00 00 00 00 00 00 00 dmidecode: 00 00 dmidecode: Strings: dmidecode: dmidecode: dmidecode: dmidecode: Handle 0x0013, DMI type 144, 26 bytes dmidecode: OEM-specific Type dmidecode: Header and Data: dmidecode: 90 1A 13 00 FF FF FF FF FF FF FF FF FF FF FF FF dmidecode: FF FF FF FF FF FF FF FF 00 00 dmidecode: dmidecode: Handle 0x0014, DMI type 127, 4 bytes dmidecode: End Of Table dmidecode: /proc/fb: 0 VESA VGA /proc/fb: 1 VGA16 VGA /etc/directfbrc: no-hardware /etc/directfbrc: bg-color=ffdcdad5 /etc/directfbrc: screenshot-dir=/var/log /etc/directfbrc: disable-module=keyboard /etc/directfbrc: disable-module=ps2mouse /etc/directfbrc: #disable-module=linux_input dfbinfo: (*) DirectFB/Config: Parsing config file '/etc/directfbrc'. dfbinfo: dfbinfo: ---------------------- DirectFB v0.9.25 --------------------- dfbinfo: (c) 2000-2002 convergence integrated media GmbH dfbinfo: (c) 2002-2004 convergence GmbH dfbinfo: ----------------------------------------------------------- dfbinfo: dfbinfo: (*) DirectFB/Core: Single Application Core. (2006-12-04 07:40) dfbinfo: (*) Direct/Memcpy: Using linux kernel memcpy() dfbinfo: (*) Direct/Thread: Running 'VT Switcher' (CRITICAL, 9735)... dfbinfo: (*) Direct/Modules: suppress module 'keyboard' dfbinfo: (*) Direct/Modules: suppress module 'ps2mouse' dfbinfo: (*) Direct/Thread: Running 'Linux Input' (INPUT, 9736)... dfbinfo: (!!!) *** UNIMPLEMENTED [fusion_reactor_set_lock] *** [../../../lib/fusion/reactor.c:853] dfbinfo: (*) DirectFB/Input: AT Translated Set 2 keyboard (1) 0.1 (convergence integrated media GmbH) dfbinfo: (*) Direct/Thread: Running 'Linux Input' (INPUT, 9737)... dfbinfo: (*) DirectFB/Input: SynPS/2 Synaptics TouchPad (2) 0.1 (convergence integrated media GmbH) dfbinfo: (*) DirectFB/Graphics: Generic Software Rasterizer 0.6 (convergence integrated media GmbH) dfbinfo: (*) DirectFB/Core/WM: Default 0.2 (Convergence GmbH) dfbinfo: dfbinfo: dfbinfo: Screen (00) FBDev Primary Screen (primary screen) dfbinfo: Caps: VSYNC POWER_MANAGEMENT dfbinfo: dfbinfo: Layer (00) FBDev Primary Layer (primary layer) dfbinfo: Type: GRAPHICS dfbinfo: Caps: SURFACE BRIGHTNESS CONTRAST SATURATION dfbinfo: dfbinfo: dfbinfo: Input (00) AT Translated Set 2 keyboard (primary keyboard) dfbinfo: Type: KEYBOARD dfbinfo: Caps: KEYS dfbinfo: dfbinfo: Input (01) SynPS/2 Synaptics TouchPad (primary mouse) dfbinfo: Type: MOUSE dfbinfo: Caps: AXES BUTTONS dfbinfo: Max. Axis: 1 dfbinfo: Max. Button: 2 dfbinfo: ============================================== Installer status: ============================================== Package: ttf-thai-tlwg-udeb Status: install ok unpacked Version: 1:0.4.5-2 Description: Thai fonts in TrueType format for D-I use Package: preseed-common Status: install ok unpacked Version: 1.28 Depends: cdebconf-udeb, di-utils (>= 1.14) Description: common files for preseeding Package: udpkg Status: install ok unpacked Version: 1.04 Depends: libc6 (>= 2.3.5-1), libdebian-installer4-udeb (>= 0.41) Description: tiny dpkg clone Package: localechooser Status: install ok installed Version: 1.37 Depends: cdebconf-udeb, iso-3166-udeb, di-utils (>= 1.15) Description: choose language/country/locale Installer-Menu-Item: 10 Package: fat-modules-2.6.18-5-amd64-di Status: install ok unpacked Version: 1.21etch1 Provides: fat-modules Depends: kernel-image-2.6.18-5-amd64-di Description: FAT filesystem support Package: libnss-dns-udeb Status: install ok unpacked Version: 2.3.6.ds1-13etch2 Description: GNU C Library: NSS helper for DNS - udeb Package: parport-modules-2.6.18-5-amd64-di Status: install ok unpacked Version: 1.21etch1 Provides: parport-modules Depends: kernel-image-2.6.18-5-amd64-di Description: Parallel port support Package: cdrom-checker Status: install ok unpacked Version: 1.11 Depends: cdrom-detect, cdebconf-udeb (>= 0.31) Description: Verify the cd contents Installer-Menu-Item: 940 Package: lowmemcheck Status: install ok unpacked Version: 1.25 Depends: cdebconf-udeb (>= 0.75), main-menu (>= 1.03) Description: detect low-memory systems and enter lowmem mode Package: cdrom-retriever Status: install ok installed Version: 1.14 Provides: retriever Depends: cdebconf-udeb, cdrom-detect Description: Fetch modules from a CDROM Package: kernel-image-2.6.18-5-amd64-di Status: install ok unpacked Version: 1.21etch1 Provides: kernel-image Description: Linux kernel binary image for the Debian installer Package: usb-serial-modules-2.6.18-5-amd64-di Status: install ok unpacked Version: 1.21etch1 Provides: usb-serial-modules Depends: kernel-image-2.6.18-5-amd64-di, usb-modules-2.6.18-5-amd64-di Description: USB serial drivers Package: main-menu Status: install ok unpacked Version: 1.18 Depends: libc6 (>= 2.3.5-1), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.49), cdebconf-udeb Description: Debian installer main menu Package: ttf-khmeros-udeb Status: install ok unpacked Version: 3.10-4 Provides: ttf-installer Description: Debian-Installer font for the Khmer language of Cambodia Package: di-utils-shell Status: install ok unpacked Version: 1.45etch1 Depends: cdebconf-udeb, di-utils (>= 1.18) Description: Execute a shell Installer-Menu-Item: 950 Package: ttf-dejavu-udeb Status: install ok unpacked Version: 2.15-1 Description: Vera font family derivate with additional characters Package: di-utils Status: install ok installed Version: 1.45etch1 Depends: libc6 (>= 2.3.5-1), libdebian-installer4-udeb (>= 0.50), cdebconf-udeb Description: Miscellaneous utilities for the debian installer Package: mouse-modules-2.6.18-5-amd64-di Status: install ok unpacked Version: 1.21etch1 Provides: mouse-modules Depends: kernel-image-2.6.18-5-amd64-di, input-modules-2.6.18-5-amd64-di, usb-modules-2.6.18-5-amd64-di Description: Mouse support Package: ttf-cjk-compact-udeb Status: install ok unpacked Version: 1.8 Description: Shrinked CJK TrueType fonts for GUI d-i. Package: cdrom-core-modules-2.6.18-5-amd64-di Status: install ok unpacked Version: 1.21etch1 Provides: cdrom-core-modules Depends: kernel-image-2.6.18-5-amd64-di, scsi-core-modules-2.6.18-5-amd64-di, ide-modules-2.6.18-5-amd64-di Description: CDROM support Package: cdebconf-newt-udeb Status: install ok unpacked Version: 0.114 Depends: cdebconf-udeb, di-utils-terminfo, libc6 (>= 2.3.5-1), libnewt0.52 Description: Newt frontend for Debian Configuration Management System Package: ttf-freefont-udeb Status: install ok unpacked Version: 20060501cvs-10 Provides: ttf-installer Description: Freefont Sans fonts for the graphical installer Package: module-init-tools-udeb Status: install ok unpacked Version: 3.3-pre4-2 Depends: libc6 (>= 2.3.5-1) Description: tools for managing Linux kernel modules Package: ide-modules-2.6.18-5-amd64-di Status: install ok unpacked Version: 1.21etch1 Provides: ide-modules Depends: kernel-image-2.6.18-5-amd64-di, ide-core-modules-2.6.18-5-amd64-di Description: IDE drivers Package: rootskel Status: install ok installed Version: 1.50 Depends: di-utils (>= 1.43), cdebconf-udeb Description: Skeleton root filesystem used by debian-installer Package: libgtk-directfb-2.0-0-udeb Status: install ok unpacked Version: 2.8.20-7 Depends: libatk1.0-udeb (>= 1.12.2), libc6 (>= 2.3.5-1), libcairo-directfb2-udeb (>= 1.2.4), libdirectfb-0.9-25-udeb, libglib2.0-udeb (>= 2.12.0), libpango1.0-udeb (>= 1.14.8), libpng12-0-udeb (>= 1.2.13-4) Description: The GTK+ graphical user interface library - minimal runtime Package: udev-udeb Status: install ok unpacked Version: 0.105-4 Depends: libc6 (>= 2.3.5-1) Description: /dev/ and hotplug management daemon Package: libpng12-0-udeb Status: install ok unpacked Version: 1.2.15~beta5-1 Depends: libc6 (>= 2.3.5-1), zlib1g-udeb (>= 1:1.2.1) Description: PNG library - minimal runtime library Package: libnss-files-udeb Status: install ok unpacked Version: 2.3.6.ds1-13etch2 Description: GNU C Library: NSS helper for files - udeb Package: brltty-udeb Status: install ok unpacked Version: 3.7.2-7.1 Depends: libc6 (>= 2.3.5-1) Description: Access software for a blind person using a soft braille terminal Package: libfribidi0-udeb Status: install ok unpacked Version: 0.10.7-4 Depends: libc6 (>= 2.3.5-1) Description: Free Implementation of the Unicode BiDi algorithm Package: libcairo-directfb2-udeb Status: install ok unpacked Version: 1.2.4-4 Depends: fontconfig-udeb (>= 2.4.0), libc6 (>= 2.3.5-1), libdirectfb-0.9-25-udeb, libfreetype6-udeb (>= 2.2), libpng12-0-udeb (>= 1.2.8rel), zlib1g-udeb (>= 1:1.2.1) Description: The Cairo 2D vector graphics library DirectFB build Package: libtextwrap1-udeb Status: install ok installed Version: 0.1-5 Depends: libc6 (>= 2.3.5-1) Description: text-wrapping library with i18n - runtime udeb Package: gtk2-engines-udeb Status: install ok unpacked Version: 1:2.8.2-1 Depends: libatk1.0-udeb (>= 1.12.2), libc6 (>= 2.3.5-1), libcairo-directfb2-udeb (>= 1.2.4), libdirectfb-0.9-25-udeb, libglib2.0-udeb (>= 2.12.0), libgtk-directfb-2.0-0-udeb (>= 2.8.0), libpango1.0-udeb (>= 1.14.7) Description: theme engines for GTK+ 2.x in the Debian installer Package: auto-install Status: install ok unpacked Version: 0.03 Depends: cdebconf-udeb, netcfg, preseed-common (>= 1.18) Description: Support for automatic installs Installer-Menu-Item: 19 Package: usb-discover Status: install ok unpacked Version: 1.06 Depends: cdebconf-udeb Description: Discover USB and load kernel modules Package: serial-modules-2.6.18-5-amd64-di Status: install ok unpacked Version: 1.21etch1 Provides: serial-modules Depends: kernel-image-2.6.18-5-amd64-di, pcmcia-modules-2.6.18-5-amd64-di Description: Serial drivers Package: usb-storage-modules-2.6.18-5-amd64-di Status: install ok unpacked Version: 1.21etch1 Provides: usb-storage-modules Depends: ide-core-modules-2.6.18-5-amd64-di, scsi-core-modules-2.6.18-5-amd64-di, usb-modules-2.6.18-5-amd64-di Description: USB storage support Package: rescue-check Status: install ok unpacked Version: 1.9 Depends: cdebconf-udeb (>= 0.75), main-menu (>= 1.03), di-utils (>= 1.18) Description: enter d-i rescue mode if requested Package: nano-udeb Status: install ok unpacked Version: 2.0.2-1etch1 Provides: editor Depends: libc6 (>= 2.3.5-1), libslang2-udeb (>= 2.0.6-3) Description: free Pico clone with some new features - tiny build Package: rootskel-gtk Status: install ok unpacked Version: 1.06 Depends: cdebconf-udeb, rootskel, mouse-modules, gtk2-engines-udeb Description: Additions for graphical installs to skeleton root filesystem (debian-installer) Package: ai-choosers Status: install ok unpacked Version: 0.03 Depends: kbd-chooser (>= 1.30), localechooser (>= 1.23) Description: Delayed configuration of locale and keyboard for auto-install Installer-Menu-Item: 22 Package: libpango1.0-udeb Status: install ok unpacked Version: 1.14.8-5 Depends: fontconfig-udeb (>= 2.4.0), libc6 (>= 2.3.5-1), libcairo-directfb2-udeb (>= 1.2.4), libfreetype6-udeb (>= 2.2), libglib2.0-udeb (>= 2.12.0), zlib1g-udeb (>= 1:1.2.1) Description: Layout and rendering of internationalized text Package: input-modules-2.6.18-5-amd64-di Status: install ok unpacked Version: 1.21etch1 Provides: input-modules Depends: kernel-image-2.6.18-5-amd64-di, usb-modules-2.6.18-5-amd64-di Description: Input devices support Package: libiw28-udeb Status: install ok installed Version: 28-1 Depends: libc6 (>= 2.3.5-1) Description: Tools for manipulating Linux Wireless Extensions Package: load-cdrom Status: install ok installed Version: 1.14 Depends: cdebconf-udeb, cdrom-retriever, anna (>= 1.07) Description: Load installer components from CD Installer-Menu-Item: 16 Package: cdebconf-text-udeb Status: install ok unpacked Version: 0.114 Depends: cdebconf-udeb, libc6 (>= 2.3.5-1) Description: Plain text frontend for Debian Configuration Management System Package: libfreetype6-udeb Status: install ok unpacked Version: 2.2.1-5+etch1 Depends: libc6 (>= 2.3.5-1), zlib1g-udeb (>= 1:1.2.1) Description: FreeType 2 font engine for the debian-installer Package: iso-3166-udeb Status: install ok installed Version: 1.0a-1 Description: provides iso_3166.tab file Package: ttf-malayalam-fonts-udeb Status: install ok unpacked Version: 1:0.4.7.4 Provides: ttf-installer Description: Free TrueType fonts for the Malayalam language Package: ttf-farsiweb-udeb Status: install ok unpacked Version: 0.4.dfsg-6 Provides: ttf-installer Description: Farsiweb TrueType fonts for the graphical installer Package: floppy-retriever Status: install ok unpacked Version: 1.14 Provides: retriever Depends: cdebconf-udeb, mountfloppy Description: Fetches modules from a floppy Package: ethdetect Status: install ok installed Version: 1.50 Provides: ethernet-card-detection Depends: rootskel (>= 1.30), cdebconf-udeb (>= 0.38), hw-detect, di-utils (>= 1.13) Description: Detect network hardware and load kernel drivers for it Installer-Menu-Item: 17 Package: libexpat1-udeb Status: install ok unpacked Version: 1.95.8-3.4 Provides: libexpat1 Depends: libc6 (>= 2.3.5-1) Description: XML parsing C library - runtime library Package: busybox-udeb Status: install ok unpacked Version: 1:1.1.3-4 Depends: libc6 (>= 2.3.5-1) Description: Tiny utilities for the debian-installer Package: initrd-preseed Status: install ok unpacked Version: 1.28 Depends: preseed-common Description: load debconf preseed file from /preseed.cfg on the initrd Package: archdetect Status: install ok installed Version: 1.50 Depends: libc6 (>= 2.3.5-1), libdebian-installer4-udeb (>= 0.49) Description: Hardware architecture detector Package: ttf-bpg-georgian-fonts-udeb Status: install ok unpacked Version: 0.3 Provides: ttf-installer Description: BPG Georgian fonts for the graphical installer Package: save-logs Status: install ok unpacked Version: 2.29 Depends: cdebconf-udeb Description: save logs and configuration for debug purposes Installer-Menu-Item: 940 Package: di-utils-reboot Status: install ok unpacked Version: 1.45etch1 Depends: cdebconf-udeb Description: Reboot Installer-Menu-Item: 995 Package: anna Status: install ok installed Version: 1.27 Depends: libc6 (>= 2.3.5-1), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.49), cdebconf-udeb Description: anna's not nearly apt, but for the Debian installer, it will do Package: libsysfs2-udeb Status: install ok unpacked Version: 2.1.0-1 Provides: libsysfs2 Depends: libc6 (>= 2.3.5-1) Description: interface library to sysfs Package: pcmciautils-udeb Status: install ok unpacked Version: 014-3 Depends: udev-udeb, libc6 (>= 2.3.5-1), libsysfs2-udeb Description: PCMCIA utilities for Linux 2.6 Package: pciutils-udeb Status: install ok unpacked Version: 1:2.2.4~pre4-1 Depends: libc6 (>= 2.3.5-1) Description: Linux PCI Utilities (udeb) Package: console-keymaps-at Status: install ok installed Version: 2:1.01-7 Provides: console-keymaps Depends: cdebconf-udeb Description: Keymaps for PC-style (PS/2 and AT) keyboards Package: ttf-tamil-fonts-udeb Status: install ok unpacked Version: 1:0.4.7.4 Provides: ttf-installer Description: Free TrueType fonts for the Tamil language Package: di-utils-terminfo Status: install ok unpacked Version: 1.45etch1 Description: Terminfo entries needed by newt/slang in debian installer Package: libdirectfb-0.9-25-udeb Status: install ok unpacked Version: 0.9.25.1-5 Provides: libdirectfb-0.9-25 Depends: libc6 (>= 2.3.5-1), libfreetype6-udeb (>= 2.2), libpng12-0-udeb (>= 1.2.8rel), libsysfs2-udeb, zlib1g-udeb (>= 1:1.2.1) Description: direct frame buffer graphics - shared libraries Package: hw-detect Status: install ok installed Version: 1.50 Depends: rootskel (>= 1.30), archdetect, cdebconf-udeb (>= 0.75), di-utils (>= 1.26) Description: Detect hardware and load kernel drivers for it Package: kbd-chooser Status: install ok installed Version: 1.34 Depends: libc6 (>= 2.3.5-1), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.49), cdebconf-udeb, console-keymaps Description: Detect a keyboard and select layout Installer-Menu-Item: 12 Package: acpi-modules-2.6.18-5-amd64-di Status: install ok unpacked Version: 1.21etch1 Provides: acpi-modules Depends: kernel-image-2.6.18-5-amd64-di Description: ACPI support modules Package: usb-modules-2.6.18-5-amd64-di Status: install ok unpacked Version: 1.21etch1 Provides: usb-modules Depends: kernel-image-2.6.18-5-amd64-di Description: USB support Package: scsi-core-modules-2.6.18-5-amd64-di Status: install ok unpacked Version: 1.21etch1 Provides: scsi-core-modules Depends: kernel-image-2.6.18-5-amd64-di Description: Core SCSI subsystem Package: fontconfig-udeb Status: install ok unpacked Version: 2.4.2-1.2 Depends: fontconfig-udeb (>= 2.4.0), libc6 (>= 2.3.5-1), libexpat1-udeb (>= 1.95.8), libfreetype6-udeb (>= 2.2), zlib1g-udeb (>= 1:1.2.1) Description: generic font configuration library - minimal runtime Package: cdebconf-gtk-udeb Status: install ok unpacked Version: 0.114 Depends: cdebconf-udeb, libatk1.0-udeb (>= 1.12.2), libc6 (>= 2.3.5-1), libcairo-directfb2-udeb (>= 1.2.4), libdirectfb-0.9-25-udeb, libglib2.0-udeb (>= 2.12.0), libgtk-directfb-2.0-0-udeb (>= 2.8.0), libpango1.0-udeb (>= 1.14.8), rootskel-gtk (>= 0.05) Description: Gtk+ frontend for Debian Configuration Management System Package: installation-locale Status: install ok unpacked Version: 1.1 Depends: rootskel Description: UTF-8 C locale Package: fb-modules-2.6.18-5-amd64-di Status: install ok unpacked Version: 1.21etch1 Provides: fb-modules Depends: kernel-image-2.6.18-5-amd64-di Description: Frame buffer support Package: env-preseed Status: install ok unpacked Version: 1.28 Description: debconf preseeding via environment variables Package: mountfloppy Status: install ok unpacked Version: 0.11 Depends: cdebconf-udeb, di-utils (>= 1.15) Description: Mounts a floppy Package: cdebconf-priority Status: install ok unpacked Version: 0.114 Depends: cdebconf-udeb Description: Change debconf priority Installer-Menu-Item: 930 Package: netcfg Status: install ok installed Version: 1.36 Provides: configured-network Depends: libc6 (>= 2.3.5-1), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.49), libiw28-udeb (>= 28), dhcp-client-udeb | dhcp3-client-udeb | pump-udeb, ethernet-card-detection Description: Configure the network Installer-Menu-Item: 18 Package: file-preseed Status: install ok unpacked Version: 1.28 Depends: cdebconf-udeb, di-utils, preseed-common Description: load debconf preseed file Installer-Menu-Item: 14 Package: ttf-tmuni-udeb Status: install ok unpacked Version: 0.0.20040806-1.2 Provides: ttf-installer Description: font for Tibetan, Dzongkha and Ladakhi (OpenType Unicode) Package: zlib1g-udeb Status: install ok unpacked Version: 1:1.2.3-13 Provides: zlib1g Description: compression library - runtime for Debian installer Package: libglib2.0-udeb Status: install ok unpacked Version: 2.12.4-2 Depends: libc6 (>= 2.3.5-1) Description: The GLib library of C routines Package: libdebconfclient0-udeb Status: install ok installed Version: 0.114 Depends: libc6 (>= 2.3.5-1), cdebconf-udeb Description: Debian Configuration Management System (C-implementation) Package: bogl-bterm-udeb Status: install ok unpacked Version: 0.1.18-1.5 Provides: editor Depends: libc-udeb Description: Ben's Own Graphics Library - graphical terminal Package: libatk1.0-udeb Status: install ok unpacked Version: 1.12.4-3 Depends: libc6 (>= 2.3.5-1), libglib2.0-udeb (>= 2.12.0) Description: The ATK accessibility toolkit Package: cdrom-detect Status: install ok installed Version: 1.20etch1 Depends: cdebconf-udeb, hw-detect, di-utils (>= 1.45etch1) Description: Detect CDROM devices and mount the CD Installer-Menu-Item: 13 Package: ide-core-modules-2.6.18-5-amd64-di Status: install ok unpacked Version: 1.21etch1 Provides: ide-core-modules Depends: kernel-image-2.6.18-5-amd64-di Description: IDE support Package: debian-installer Status: install ok installed Version: cdrom-gtk-20070308etch1 Description: debian installation image Package: cdebconf-udeb Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 216 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 0.114etch1 Depends: libc6 (>= 2.3.5-1), libdebian-installer4-udeb (>= 0.50), libtextwrap1-udeb Provides: debconf-2.0 Description: Debian Configuration Management System (C-implementation) Debconf is a configuration management system for Debian packages. It is used by some packages to prompt you for information before they are installed. This is a reimplementation of the original debconf version in C. . cdebconf-udeb is a minimal cdebconf package used by the debian-installer Package: apt-cdrom-setup Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 44 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1:0.20etch1 Depends: cdrom-detect, cdebconf-udeb Provides: apt-mirror-setup Description: set up a CD in sources.list Package: apt-mirror-setup Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 160 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1:0.20etch1 Depends: choose-mirror-bin, cdebconf-udeb Description: set up a mirror in sources.list Package: apt-setup-udeb Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 104 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1:0.20etch1 Depends: apt-mirror-setup, base-installer (>= 1.49), cdebconf-udeb Description: Configure apt Installer-Menu-Item: 70 Package: base-installer Status: install ok installed Priority: required Section: debian-installer Installed-Size: 632 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.76 Depends: libc6 (>= 2.3.5-1), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.50), mounted-partitions, debootstrap-udeb (>= 0.3.1), created-fstab, archdetect, di-utils-mapdevfs, di-utils (>= 1.16), rootskel (>= 1.19), gpgv-udeb Provides: kernel-installer Description: Install the base system Installer-Menu-Item: 65 Package: choose-mirror-bin Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 344 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 2.13etch1 Depends: libc6 (>= 2.3.5-1), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.50), cdebconf-udeb Description: Choose mirror to install from (program) Package: clock-setup Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 76 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 0.15 Depends: cdebconf-udeb, os-prober, tzsetup-udeb Description: set up clock Installer-Menu-Item: 62 Package: core-modules-2.6.18-5-amd64-di Status: install ok unpacked Priority: standard Section: debian-installer Installed-Size: 80 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di Provides: core-modules Description: Core modules This package contains core modules for the kernel, that will almost always be needed. Package: crc-modules-2.6.18-5-amd64-di Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 40 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di Provides: crc-modules Description: CRC modules This package contains CRC support modules. Package: crypto-modules-2.6.18-5-amd64-di Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 212 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di Provides: crypto-modules Description: crypto modules This package contains crypto modules. Package: debootstrap-udeb Status: install ok installed Priority: required Section: debian-installer Installed-Size: 200 Maintainer: Anthony Towns <ajt@debian.org> Version: 0.3.3.2etch1 Depends: libc6 (>= 2.3.5-1), mounted-partitions Description: Bootstrap the Debian system debootstrap is used to create a Debian base system from scratch, without requiring the availability of dpkg or apt. It does this by downloading .deb files from a mirror site, and carefully unpacking them into a directory which can eventually be chrooted into. . debootstrap-udeb is a minimal package used by debian-installer. Package: dhcp-client-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 160 Maintainer: Eloy A. Paris <peloy@debian.org> Version: 2.0pl5-19.5etch2 Depends: libc6 (>= 2.3.5-1) Description: DHCP Client for debian-installer dhcp-client-udeb is a minimal dhcp package used by the debian-installer. Package: di-utils-mapdevfs Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 20 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.45etch1 Depends: libc6 (>= 2.3.5-1), libdebian-installer4-udeb (>= 0.50) Description: mapdevfs utility for the debian installer Package: disk-detect Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 64 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.50 Depends: cdebconf-udeb (>= 0.38), hw-detect, di-utils (>= 1.13) Provides: harddrive-detection Description: Detect disk drives Installer-Menu-Item: 35 Package: dmidecode-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 76 Maintainer: Petter Reinholdtsen <pere@debian.org> Version: 2.8-4 Depends: libc6 (>= 2.3.5-1) Description: Dump Desktop Management Interface data (udeb) Package: e2fsprogs-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 428 Maintainer: Theodore Y. Ts'o <tytso@mit.edu> Version: 1.39+1.40-WIP-2006.11.14+dfsg-2etch1 Depends: libblkid1-udeb, libc6 (>= 2.3.5-1) Description: stripped-down versions of e2fsprogs, for debian-installer This package is an e2fsprogs package built for a reduced size, so that it can help to save space in debian-installer. . Don't attempt to install this package, it has no support for a couple of features you surely want. Anyway it should refuse to install. Package: ext2-modules-2.6.18-5-amd64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 136 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di, core-modules-2.6.18-5-amd64-di Provides: ext2-modules Description: EXT2 filesystem support This package contains the EXT2 filesystem module for the Linux kernel. Package: ext3-modules-2.6.18-5-amd64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 348 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di, core-modules-2.6.18-5-amd64-di Provides: ext3-modules Description: EXT3 filesystem support This package contains the EXT3 filesystem module for the Linux kernel. Package: fdisk-udeb Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 168 Maintainer: LaMont Jones <lamont@debian.org> Version: 2.12r-19 Depends: libc6 (>= 2.3.5-1) Description: Partition a hard drive (manual) fdisk package Package: finish-install Status: install ok unpacked Priority: required Section: debian-installer Installed-Size: 108 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 2.9 Depends: cdebconf-udeb, archdetect, base-installer, created-fstab, bootable-system Provides: prebaseconfig Description: Finish the installation and reboot Installer-Menu-Item: 78 Package: firewire-core-modules-2.6.18-5-amd64-di Status: install ok unpacked Priority: standard Section: debian-installer Installed-Size: 696 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: scsi-core-modules-2.6.18-5-amd64-di, kernel-image-2.6.18-5-amd64-di Provides: firewire-core-modules Description: Core FireWire drivers This package contains core FireWire drivers for the Linux kernel. Package: floppy-modules-2.6.18-5-amd64-di Status: install ok unpacked Priority: standard Section: debian-installer Installed-Size: 152 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di Provides: floppy-modules Description: Floppy driver This package contains the floppy driver for the Linux kernel. Package: gpgv-udeb Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 292 Maintainer: James Troup <james@nocrew.org> Version: 1.4.6-2 Depends: libc6 (>= 2.3.5-1), zlib1g-udeb (>= 1:1.2.1) Description: minimal signature verification tool GnuPG is GNU's tool for secure communication and data storage. It can be used to encrypt data and to create digital signatures. It includes an advanced key management facility and is compliant with the proposed OpenPGP Internet standard as described in RFC2440. . This is GnuPG's signature verification tool, gpgv, packaged in minimal form for use in debian-installer. Package: grub-installer Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 348 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.22etch1 Depends: cdebconf-udeb, kernel-installer, created-fstab, di-utils (>= 1.15), di-utils-mapdevfs, os-prober, dmidecode-udeb (>= 2.7) Provides: bootable-system Description: Install GRUB on a hard disk Installer-Menu-Item: 73 Package: jfs-modules-2.6.18-5-amd64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 276 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di Provides: jfs-modules Description: JFS filesystem support This package contains the JFS filesystem module for the Linux kernel. Package: jfsutils-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 1004 Maintainer: Stefan Hornburg (Racke) <racke@linuxia.de> Version: 1.1.11-1 Depends: libc6 (>= 2.3.5-1), libuuid1-udeb Description: A stripped-down version of jfsutils, for debian-installer This package is a jfsutils package built for reduced size, so that it can help to save space in debian-installer. . Don't attempt to install this package, it has no support for a couple of features you surely want. Anyway, it should fail to install. Package: libblkid1-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 48 Maintainer: Theodore Y. Ts'o <tytso@mit.edu> Version: 1.39+1.40-WIP-2006.11.14+dfsg-2etch1 Depends: libc6 (>= 2.3.5-1) Provides: libblkid1 Description: block device id library The blkid library which allows system programs like fsck and mount to quickly and easily find block devices by filesystem UUID and LABEL. This allows system administrators to avoid specifiying filesystems by hard-coded device names, but via a logical naming system instead. . This is a minimal package for debian-installer. Package: libc6-udeb Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 2128 Maintainer: GNU Libc Maintainers <debian-glibc@lists.debian.org> Version: 2.3.6.ds1-13etch4 Provides: libc6, libc-udeb, glibc-2.3.6.ds1-1, glibc-2.3.6-2 Description: GNU C Library: Shared libraries - udeb Contains the standard libraries that are used by nearly all programs on the system. This package includes shared versions of the standard C library and the standard math library, as well as many others. . This package contains a minimal set of libraries needed for the Debian installer. Do not install it on a normal system. Package: libcrypto0.9.8-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 1496 Maintainer: Debian OpenSSL Team <pkg-openssl-devel@lists.alioth.debian.org> Version: 0.9.8c-4etch1 Depends: libc6 (>= 2.3.5-1), zlib1g-udeb (>= 1:1.2.1) Provides: libssl0.9.8 Description: crypto shared library - udeb libcrypto shared library. . Do not install it on a normal system. Package: libdevmapper1.02-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 84 Maintainer: Debian LVM Team <pkg-lvm-maintainers@lists.alioth.debian.org> Version: 2:1.02.08-1 Depends: libc6 (>= 2.3.5-1) Provides: libdevmapper1.02 Description: The Linux Kernel Device Mapper userspace library This is a udeb, or a microdeb, for the debian-installer. . The Linux Kernel Device Mapper is the LVM (Linux Logical Volume Management) Team's implementation of a minimalistic kernel-space driver that handles volume management, while keeping knowledge of the underlying device layout in user-space. This makes it useful for not only LVM, but EVMS, software raid, and other drivers that create "virtual" block devices. Package: libparted1.7-udeb Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 352 Maintainer: Parted Maintainer Team <parted-maintainers@lists.alioth.debian.org> Version: 1.7.1-5.1 Depends: libc6 (>= 2.3.5-1), libuuid1-udeb Provides: libparted1.7-1 Description: The GNU Parted disk partitioning shared library GNU Parted is a program that allows you to create, destroy, resize, move and copy hard disk partitions. This is useful for creating space for new operating systems, reorganising disk usage, and copying data to new hard disks. This package contains the Parted binary and manual page. . This package contains libparted, the required shared library used by Parted. This is a cut-down package with no normal documentation intended to be used in debian-installer. . Parted currently supports DOS, Mac, Sun, BSD, GPT, MIPS and PC98 disklabels/partition tables, as well as a 'loop' (raw disk) type which allows use on RAID/LVM. Filesystems which are currently fully supported are ext2, ext3, fat (FAT16 and FAT32), ReiserFS (with libreiserfs) and linux-swap. Parted can also detect and remove HFS (Mac OS), JFS, NTFS, UFS (Sun and HP), XFS and ASFS/AFFS/APFS (Amiga) filesystems, but cannot create, resize or check these filesystems yet. . Note that ReiserFS support is only enabled if you install the libreiserfs0.3-0 package. Since libreiserfs0.3-0 has been removed from sarge, ReiserFS support is not compiled in the default package. . The nature of this software means that any bugs could cause massive data loss. While there are no known bugs at the moment, they could exist, so please back up all important files before running it, and do so at your own risk. Package: libuuid1-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 24 Maintainer: Theodore Y. Ts'o <tytso@mit.edu> Version: 1.39+1.40-WIP-2006.11.14+dfsg-2etch1 Depends: libc6 (>= 2.3.5-1) Provides: libuuid1 Description: universally unique id library libuuid generates and parses 128-bit universally unique id's (UUID's). See RFC 4122 for more information. . This is a minimal package for debian-installer. Package: lilo-installer Status: install ok unpacked Priority: standard Section: debian-installer Installed-Size: 232 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.20etch1 Depends: cdebconf-udeb, kernel-installer, di-utils (>= 1.15), di-utils-mapdevfs, fdisk-udeb, os-prober, dmidecode-udeb (>= 2.7) Provides: bootable-system Description: Install LILO on a hard disk Installer-Menu-Item: 75 Package: loop-modules-2.6.18-5-amd64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 60 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di Provides: loop-modules Description: Loopback filesystem support This package contains loopback filesystem support for the Linux kernel. Package: lvm2-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 472 Maintainer: Debian LVM Team <pkg-lvm-maintainers@lists.alioth.debian.org> Version: 2.02.06-4etch1 Depends: libc6 (>= 2.3.5-1), libdevmapper1.02-udeb (>= 2:1.02.02-2) Description: The Linux Logical Volume Manager This is a udeb, or a microdeb, for the debian-installer. . This is LVM2, the rewrite of The Linux Logical Volume Manager. LVM supports enterprise level volume management of disk and disk subsystems by grouping arbitrary disks into volume groups. The total capacity of volume groups can be allocated to logical volumes, which are accessed as regular block devices. Package: md-modules-2.6.18-5-amd64-di Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 592 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di Provides: md-modules Description: RAID and LVM support This package contains RAID and LVM modules for the Linux kernel. Package: mdadm-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 184 Maintainer: Debian mdadm maintainers <pkg-mdadm-devel@lists.alioth.debian.org> Version: 2.5.6-9 Depends: libc6 (>= 2.3.5-1) Description: tool to administer Linux MD arrays (software RAID) mdadm is a program that can be used to create, manage, and monitor MD arrays (e.g. software RAID, multipath devices). . mdadm-udeb is a minimal package used by the debian-installer. Package: mdcfg-utils Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 412 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21 Depends: cdebconf-udeb, di-utils (>= 1.16), md-modules, mdadm-udeb (>= 2.5.2), partconf-find-partitions Description: Configure MD devices Use this module to configure the MD devices. Package: mkreiserfs-udeb Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 168 Maintainer: Ed Boraas <ed@debian.org> Version: 1:3.6.19-4 Depends: libc6 (>= 2.3.5-1), libuuid1-udeb Description: User-level tools for ReiserFS filesystems This installer module contains the utility to create ReiserFS filesystems. . Homepage: http://www.namesys.com/ Package: network-preseed Status: install ok unpacked Priority: standard Section: debian-installer Installed-Size: 40 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.28 Depends: cdebconf-udeb, configured-network, preseed-common Description: download debconf preseed file Installer-Menu-Item: 21 Package: nic-extra-modules-2.6.18-5-amd64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 3160 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di, nic-shared-modules-2.6.18-5-amd64-di, core-modules-2.6.18-5-amd64-di, crc-modules-2.6.18-5-amd64-di Provides: nic-extra-modules Description: Rare NIC drivers This package contains rare NIC drivers for the Linux kernel. Package: nic-modules-2.6.18-5-amd64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 620 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di, nic-shared-modules-2.6.18-5-amd64-di, core-modules-2.6.18-5-amd64-di, firewire-core-modules-2.6.18-5-amd64-di Provides: nic-modules Description: Common NIC drivers This package contains common NIC drivers for the Linux kernel. Package: nic-pcmcia-modules-2.6.18-5-amd64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 788 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di, nic-shared-modules-2.6.18-5-amd64-di, nic-extra-modules-2.6.18-5-amd64-di, pcmcia-modules-2.6.18-5-amd64-di Provides: nic-pcmcia-modules Description: Common PCMCIA NIC drivers This package contains common PCMCIA NIC drivers for the Linux kernel. Package: nic-shared-modules-2.6.18-5-amd64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 68 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di Provides: nic-shared-modules Description: Shared NIC drivers This package contains NIC drivers needed by combinations of nic-modules, nic-extra-modules, and nic-pcmcia-modules. Package: nic-usb-modules-2.6.18-5-amd64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 296 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di, nic-shared-modules-2.6.18-5-amd64-di, usb-modules-2.6.18-5-amd64-di, core-modules-2.6.18-5-amd64-di Provides: nic-usb-modules Description: USB NIC drivers This package contains USB network adapter drivers for the Linux kernel. Package: nobootloader Status: install ok unpacked Priority: standard Section: debian-installer Installed-Size: 168 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.17 Depends: cdebconf-udeb, base-installer (>= 1.23), di-utils-mapdevfs Provides: bootable-system Description: Don't install any bootloader. This package will skip installing a boot-loader Installer-Menu-Item: 77 Package: ntfsprogs-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 232 Maintainer: David Martínez Moreno <ender@debian.org> Version: 1.13.1-6+b2 Depends: libc6 (>= 2.3.5-1) Provides: ntfstools-udeb Description: Tools for doing neat things in NTFS partitions from Linux - udeb Currently this udeb contains only ntfsresize. Package: openssh-client-udeb Status: install ok unpacked Priority: optional Section: debian-installer Installed-Size: 376 Maintainer: Matthew Vernon <matthew@debian.org> Version: 1:4.3p2-9 Depends: libc6 (>= 2.3.5-1), libcrypto0.9.8-udeb (>= 0.9.8c-1), zlib1g-udeb (>= 1:1.2.1), libnss-files-udeb Description: Secure shell client for the Debian installer This is the portable version of OpenSSH, a free implementation of the Secure Shell protocol as specified by the IETF secsh working group. . This package provides the ssh client for use in debian-installer. Installer-Menu-Item: 999 Package: os-prober-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 128 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.17 Depends: di-utils-mapdevfs, anna (>= 1.16) Provides: os-prober Description: utility to detect other OSes on a set of drives This package is to be used by boot loader installers to detect other OSes available on a system, in a generic format, which it can then adapt to its own configuration format. Package: partconf-find-partitions Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 36 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21 Depends: libc6 (>= 2.3.5-1), libdebian-installer4-udeb (>= 0.49), libparted1.7-udeb (>= 1.7.1-1) Description: debian-installer utility for finding partitions Helper program for finding partitions and detecting their size and existing file system. Package: parted-udeb Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 76 Maintainer: Parted Maintainer Team <parted-maintainers@lists.alioth.debian.org> Version: 1.7.1-5.1 Depends: libc6 (>= 2.3.5-1), libparted1.7-udeb (>= 1.7.1-1) Provides: parted Description: The GNU Parted disk partition resizing program GNU Parted is a program that allows you to create, destroy, resize, move and copy hard disk partitions. This is useful for creating space for new operating systems, reorganising disk usage, and copying data to new hard disks. This package contains the Parted binary and manual page. . This package is similar to the "big" parted package, but has less cosmetical features resulting in smaller binary. Intended to be used in debian-installer. . . The nature of this software means that any bugs could cause massive data loss. While there are no known bugs at the moment, they could exist, so please back up all important files before running it, and do so at your own risk. Package: partman-auto Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 392 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 68etch1 Depends: cdebconf-udeb, di-utils, partman-base (>= 99), partman-basicfilesystems, partman-ext3 Description: Automatically partition storage devices (partman) Package: partman-auto-crypto Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 48 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 5 Depends: cdebconf-udeb, partman-auto (>= 55), partman-auto-lvm (>= 14), partman-crypto (>= 13), partman-base (>= 87) Description: Automatically partition storage devices using crypto and LVM Package: partman-auto-lvm Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 164 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 22 Depends: cdebconf-udeb, partman-base (>= 73), partman-auto (>= 59), partman-lvm (>= 36), di-utils (>= 1.15), lvm2-udeb Description: Automatically partition storage devices using LVM Package: partman-auto-raid Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 68 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 5 Depends: cdebconf-udeb, partman-base (>= 99), partman-basicfilesystems, partman-ext3, partman-auto (>= 58), partman-md Description: Allow preseeded RAID installs Package: partman-base Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 888 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 105 Depends: libc6 (>= 2.3.5-1), libparted1.7-udeb (>= 1.7.1-1), cdebconf-udeb, partman-partitioning, partman-target, archdetect, harddrive-detection, di-utils-mapdevfs, di-utils (>= 1.15) Provides: made-filesystems, mounted-partitions, partitioned-harddrives, created-fstab Description: Partition the storage devices (partman) Installer-Menu-Item: 42 Package: partman-basicfilesystems Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 600 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 53 Depends: cdebconf-udeb, e2fsprogs-udeb, ext2-modules, fat-modules, di-utils (>= 1.14) Provides: partman-filesystem Description: Add to partman support for ext2, linux-swap, fat16 and fat32 Package: partman-basicmethods Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 132 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 34 Depends: cdebconf-udeb Provides: partman-method Description: Basic partition usage methods for partman This package provides partman with two methods to use partitions. The first is to format the partition. The second is to keep and use the existing data in the partition as it is. Package: partman-crypto Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 788 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 20etch1 Depends: partman-base (>= 87), libc6 (>= 2.3.5-1), cdebconf-udeb Description: Add to partman support for block device encryption Package: partman-ext3 Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 228 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 46 Depends: cdebconf-udeb, e2fsprogs-udeb, ext3-modules, partman-basicfilesystems, di-utils (>= 1.14) Provides: partman-filesystem Description: Add to partman support for ext3 Package: partman-jfs Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 272 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 21 Depends: cdebconf-udeb, jfsutils-udeb, jfs-modules, partman-basicfilesystems, di-utils (>= 1.14) Provides: partman-filesystem Description: Add support for jfs to partman Package: partman-lvm Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 732 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 53 Depends: cdebconf-udeb, partman-base (>= 87), di-utils (>= 1.14), md-modules, lvm2-udeb, parted-udeb Description: Adds support for LVM to partman Package: partman-md Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 160 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 34 Depends: cdebconf-udeb, mdadm-udeb, mdcfg-utils, partman-base (>= 87) Description: Add to partman support for MD Package: partman-partitioning Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 380 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 48etch1 Depends: ntfsprogs-udeb, cdebconf-udeb Description: Partitioning operations for partman This udeb provides partman with editing operations for creation of new partitions, deletion of partitions and initialisation of the partition table. Package: partman-reiserfs Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 236 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 35 Depends: cdebconf-udeb, mkreiserfs-udeb, reiserfs-modules, partman-basicfilesystems, di-utils (>= 1.14) Provides: partman-filesystem Description: Add to partman support for reiserfs Package: partman-target Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 320 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 49 Depends: cdebconf-udeb, partman-basicfilesystems, partman-basicmethods, di-utils-mapdevfs Description: Provides partman with ability to prepare /target This udeb allows the user to choose how partitions should be used. Package: partman-xfs Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 224 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 33 Depends: cdebconf-udeb, xfsprogs-udeb, xfs-modules, partman-basicfilesystems, di-utils (>= 1.14) Provides: partman-filesystem Description: Add to partman support for xfs Package: pcmcia-modules-2.6.18-5-amd64-di Status: install ok unpacked Priority: standard Section: debian-installer Installed-Size: 252 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di, core-modules-2.6.18-5-amd64-di Provides: pcmcia-modules Description: Common PCMCIA drivers This package contains common PCMCIA drivers for the Linux kernel. Package: pcmcia-storage-modules-2.6.18-5-amd64-di Status: install ok unpacked Priority: standard Section: debian-installer Installed-Size: 60 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di, ide-core-modules-2.6.18-5-amd64-di, cdrom-core-modules-2.6.18-5-amd64-di, pcmcia-modules-2.6.18-5-amd64-di Provides: pcmcia-storage-modules Description: PCMCIA storage drivers This package contains PCMCIA storage drivers for the Linux kernel. Package: pkgsel Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 32 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 0.12 Depends: cdebconf-udeb, apt-setup-udeb, di-utils (>= 1.20) Description: Select and install packages Installer-Menu-Item: 70 Package: reiserfs-modules-2.6.18-5-amd64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 352 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di Provides: reiserfs-modules Description: Reiser filesystem support This package contains the Reiser filesystem module for the Linux kernel. Package: sata-modules-2.6.18-5-amd64-di Status: install ok unpacked Priority: standard Section: debian-installer Installed-Size: 600 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di, scsi-core-modules-2.6.18-5-amd64-di Provides: sata-modules Description: SATA drivers This package contains SATA drivers for the Linux kernel. Package: scsi-common-modules-2.6.18-5-amd64-di Status: install ok unpacked Priority: standard Section: debian-installer Installed-Size: 864 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di, scsi-core-modules-2.6.18-5-amd64-di, cdrom-core-modules-2.6.18-5-amd64-di Provides: scsi-common-modules Description: Very common SCSI drivers This package contains very common SCSI drivers for the Linux kernel. Package: scsi-extra-modules-2.6.18-5-amd64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 1928 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: scsi-modules-2.6.18-5-amd64-di, scsi-core-modules-2.6.18-5-amd64-di Provides: scsi-extra-modules Description: Uncommon SCSI drivers This package contains uncommon SCSI drivers for the Linux kernel. This includes SCSI RAID drivers, and some of the less common SCSI controllers. Package: scsi-modules-2.6.18-5-amd64-di Status: install ok unpacked Priority: standard Section: debian-installer Installed-Size: 696 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di, scsi-core-modules-2.6.18-5-amd64-di, scsi-common-modules-2.6.18-5-amd64-di, parport-modules-2.6.18-5-amd64-di, cdrom-core-modules-2.6.18-5-amd64-di, core-modules-2.6.18-5-amd64-di Provides: scsi-modules Description: SCSI drivers This package contains SCSI drivers for the Linux kernel. Package: tzsetup-udeb Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 308 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1:0.16 Depends: cdebconf-udeb, localechooser Description: choose timezone Installer-Menu-Item: 62 Package: user-setup-udeb Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 360 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.11etch1 Depends: cdebconf-udeb Description: Set up users and passwords Installer-Menu-Item: 63 Package: wireless-tools-udeb Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 48 Maintainer: Guus Sliepen <guus@debian.org> Version: 28-1 Depends: libc6 (>= 2.3.5-1), libiw28-udeb (>= 28) Description: Tools for manipulating Linux Wireless Extensions This package contains the Wireless tools, used to manipulate the Linux Wireless Extensions. The Wireless Extension is an interface allowing you to set Wireless LAN specific parameters and get the specific stats. . This is a udeb of the wireless tools. Package: xfs-modules-2.6.18-5-amd64-di Status: install ok installed Priority: standard Section: debian-installer Installed-Size: 696 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di Provides: xfs-modules Description: XFS filesystem support This package contains the XFS filesystem module for the Linux kernel. Package: xfsprogs-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 272 Maintainer: Nathan Scott <nathans@debian.org> Version: 2.8.11-1 Depends: libc6 (>= 2.3.5-1), libuuid1-udeb Description: A stripped-down version of xfsprogs, for debian-installer This package is an xfsprogs package built for reduced size, so that it can help to save space in debian-installer. . Don't attempt to install this package, it has no support for a couple of features you surely want. Anyway, it should fail to install. Package: libdebian-installer4-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 52 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 0.50etch1 Depends: libc6 (>= 2.3.5-1) Description: Library of common debian-installer functions This library is used by debian-installer to perform common functions such as logging messages and executing commands. If you aren't working on debian-installer or building your own install system based on debian-installer, then you probably don't need this library. Package: cdebconf-newt-entropy Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 40 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 0.4 Depends: cdebconf-newt-udeb, libc6 (>= 2.3.5-1), libnewt0.52 Description: cdebconf newt plugin for reading from /dev/random cdebconf plugin to facilitate reading random data from /dev/random. Asks the user to enter random characters on the keyboard and shows a progressbar with percent-of-data read. Package: cryptsetup-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 436 Maintainer: Debian Cryptsetup Team <pkg-cryptsetup-devel@lists.alioth.debian.org> Version: 2:1.0.4+svn26-1 Depends: libc6 (>= 2.3.5-1), libdevmapper1.02-udeb (>= 2:1.02.02-2), libpopt0-udeb (>= 1.10), libuuid1-udeb, dmsetup-udeb Description: configures encrypted block devices Since kernel 2.6.4, encrypted filesystem support is provided by the device mapper target dm-crypt. This utility provides a command-line interface for configuring this facility. It has integrated support for LUKS. . cryptsetup is backwards compatible with the on-disk format of cryptoloop, but also supports more secure formats. This package also includes support for automatically configuring encrypted devices at boot time via the config file /etc/crypttab. When combined with newer versions of the debian initrd-tools and standard debian kernels, cryptoroot is also supported. Package: dmsetup-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 40 Maintainer: Debian LVM Team <pkg-lvm-maintainers@lists.alioth.debian.org> Version: 2:1.02.08-1 Depends: libc6 (>= 2.3.5-1), libdevmapper1.02-udeb (>= 2:1.02.02-2) Description: The Linux Kernel Device Mapper userspace library The Linux Kernel Device Mapper is the LVM (Linux Logical Volume Management) Team's implementation of a minimalistic kernel-space driver that handles volume management, while keeping knowledge of the underlying device layout in user-space. This makes it useful for not only LVM, but EVMS, software raid, and other drivers that create "virtual" block devices. . This package contains a utility for modifying device mappings. Package: libpopt0-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 40 Maintainer: Paul Martin <pm@debian.org> Version: 1.10-3 Depends: libc6 (>= 2.3.5-1) Description: lib for parsing cmdline parameters Popt was heavily influenced by the getopt() and getopt_long() functions, but it allows more powerful argument expansion. It can parse arbitrary argv[] style arrays and automatically set variables based on command line arguments. It also allows command line arguments to be aliased via configuration files and includes utility functions for parsing arbitrary strings into argv[] arrays using shell-like rules. . This package contains the runtime library and locale data. . This is a minimal package for use in debian-installer. Package: partman-crypto-dm Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 60 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 20etch1 Depends: partman-crypto, crypto-modules, cryptsetup-udeb, cdebconf-newt-entropy (>= 0.3) Description: Add to partman support for dm-crypt encryption Package: gnupg-udeb Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 776 Maintainer: James Troup <james@nocrew.org> Version: 1.4.6-2 Depends: libc6 (>= 2.3.5-1), libusb-0.1-udeb (>= 2:0.1.12), zlib1g-udeb (>= 1:1.2.1) Description: GNU privacy guard - a free PGP replacement GnuPG is GNU's tool for secure communication and data storage. It can be used to encrypt data and to create digital signatures. It includes an advanced key management facility and is compliant with the proposed OpenPGP Internet standard as described in RFC2440. . This is GnuPG packaged in minimal form for use in debian-installer. Package: libusb-0.1-udeb Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 44 Maintainer: Aurelien Jarno <aurel32@debian.org> Version: 2:0.1.12-5 Depends: libc6 (>= 2.3.5-1) Provides: libusb-0.1-4 Description: userspace USB programming library Library for programming USB applications without the knowledge of Linux kernel internals. . More information can be found at the Linux USB web site http://www.linux-usb.org/ . . This is a minimal package for use in debian-installer. Package: loop-aes-modules-2.6.18-5-amd64-di Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 192 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.03etch1 Depends: kernel-image-2.6.18-5-amd64-di Provides: loop-aes-modules Description: loop-AES crypto modules This package contains loop-AES crypto modules. Package: mount-aes-udeb Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 252 Maintainer: Debian Loop-AES Team <pkg-loop-aes-maint@lists.alioth.debian.org> Version: 2.12r-15+b1 Depends: libblkid1-udeb (>= 1.37-1), libc6 (>= 2.3.5-1), libuuid1-udeb Description: Mount utils for loop-AES loop-AES patched mount, losetup and swapon Package: partman-crypto-loop Status: install ok installed Priority: optional Section: debian-installer Installed-Size: 76 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 20etch1 Depends: partman-crypto, loop-aes-modules, mount-aes-udeb, gnupg-udeb, cdebconf-newt-entropy (>= 0.3) Description: Add to partman support for loop-AES encryption Package: ntfs-modules-2.6.18-5-amd64-di Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 324 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di Provides: ntfs-modules Description: NTFS filesystem support This package contains the NTFS file system module for the Linux kernel. Package: qnx4-modules-2.6.18-5-amd64-di Status: install ok installed Priority: extra Section: debian-installer Installed-Size: 56 Maintainer: Debian Install System Team <debian-boot@lists.debian.org> Version: 1.21etch2 Depends: kernel-image-2.6.18-5-amd64-di Provides: qnx4-modules Description: QNX4 filesystem support This package contains the QNX4 filesystem module for the Linux kernel. -- System Information: Debian Release: 4.0 APT prefers stable APT policy: (500, 'stable') Architecture: amd64 (x86_64) Shell: /bin/sh linked to /bin/bash Kernel: Linux 2.6.18-5-amd64 Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8) installation-report depends on no packages. Versions of packages installation-report recommends: ii pciutils 1:2.2.4~pre4-1 Linux PCI Utilities ii reportbug 3.31 reports bugs in the Debian distrib -- no debconf information
Attachment:
signature.asc
Description: Digital signature