Bug#308628: Package: installation-reports
Package: installation-reports
Package: installation-reports
Package: installation-reports
Package: installation-reports
hi.
This references an debian sarge install on a Thinkpad
with a xircom RBE-100 nic.
this hardware works fine on other MS os's, so i dont
suspect hardware failure.
Package: installation-reports
Debian-installer-version: debian sarge most likely
from http://cdimage.debian.org/pub/weekly/i386/
uname -a: not captured, but chose linux26 and expert26
during install.
Date: May 7, 8, 9 and 10th!
Method: booted from sarge cd
Machine: IBM THinkpad iSeries, 2611
Processor: Mobile Pentium MMX 266
Memory: 256megs
Root Device: ide, 20gigs
Root Size/partition table: default "All files on one
partition", plus swap part
Output of lspci and lspci -n:
0000:00:00.0 Host bridge: ALi Corporation M1531
[Aladdin IV] (rev b3)
Subsystem: ALi Corporation M1531 [Aladdin IV]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow
>TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
0000:00:02.0 ISA bridge: ALi Corporation M1533 PCI to
ISA Bridge [Aladdin IV] (rev 0a)
Subsystem: ALi Corporation ALI M1533 Aladdin IV ISA
Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr-
DEVSEL=medium >TAbort- <TAbort+ <MAbort+ >SERR- <PERR-
Latency: 0
0000:00:05.0 CardBus bridge: O2 Micro, Inc.
OZ6832/6833 Cardbus Controller (rev 34)
Subsystem: O2 Micro, Inc. OZ6832/6833 Cardbus
Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 10000000 (32-bit,
non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=04,
sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset-
16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:00:05.1 CardBus bridge: O2 Micro, Inc.
OZ6832/6833 Cardbus Controller (rev 34)
Subsystem: O2 Micro, Inc. OZ6832/6833 Cardbus
Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow
>TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 168
Interrupt: pin B routed to IRQ 9
Region 0: Memory at 10001000 (32-bit,
non-prefetchable) [size=4K]
Bus: primary=00, secondary=05, subordinate=08,
sec-latency=176
Memory window 0: 10c00000-10fff000 (prefetchable)
Memory window 1: 12400000-127ff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset-
16bInt- PostWrite+
16-bit legacy interface ports at 0001
0000:00:06.0 VGA compatible controller: Neomagic
Corporation NM2160 [MagicGraph 128XD] (rev 01)
(prog-if 00 [VGA])
Subsystem: Unknown device 0004:10c8
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 11000000 (32-bit, prefetchable)
[size=16M]
Region 1: Memory at 12000000 (32-bit,
non-prefetchable) [size=2M]
Region 2: Memory at 12200000 (32-bit,
non-prefetchable) [size=1M]
0000:00:0b.0 IDE interface: ALi Corporation M5229 IDE
(rev 20) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 15
Region 4: I/O ports at 6090 [size=16]
0000:00:0c.0 Bridge: ALi Corporation M7101 Power
Management Controller [PMU] (rev 09)
Subsystem: ALi Corporation: Unknown device 1533
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
0000:05:00.0 Ethernet controller: Xircom Cardbus
Ethernet 10/100 (rev 03)
Subsystem: Xircom Cardbus Ethernet 10/100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (5000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at 4800 [size=128]
Region 1: Memory at 12400000 (32-bit,
non-prefetchable) [size=2K]
Region 2: Memory at 12400800 (32-bit,
non-prefetchable) [size=2K]
Expansion ROM at 10c00000 [disabled] [size=16K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] =
didn't try it
Initial boot worked: [ o]
Configure network HW: [ o]
Config network: [ E]
Detect CD: [ o]
Load installer modules: [ o]
Detect hard drives: [o ]
Partition hard drives: [ o]
Create file systems: [o ]
Mount partitions: [o ]
Install base system: [o ]
Install boot loader: [o ]
Reboot: [o ]
Comments/Problems:
The debian sarge installer detected my xircom RBE-100
fine during install and got DHCP ip assigned via my
Netgear router. During install i went to tty2 to
confirm ip and it was correct. Install proceeded
fine, however, upon reboot, card was detected,
configured and was awaiting DHCP ip, but never got
one. dhclient eth0 tries x number of times, but never
gets an answer. Static IP does not seem to work
either.
My guess is, installer is using generic pcmcia or
xircom driver, but upon reboot it uses a more specific
one, which just doesnt work.
please advise:
Mike
mleo963@yahoo.com
__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
Reply to: