RE: Hi there, install sarge on IBM xseries 305
Package: installation-reports
Debian-installer-version: sarge
http://cdimage.debian.org/pub/cdimage-testing/sarge_d-i/i386/rc2/sarge-i
386-netinst.iso
uname -a: Linux nagios 2.4.27-1-386 #1 Fri Sep 3 06:24:46 UTC 2004 i686
GNU/Linux
Date: 22/12/2004
Method: net-inst http proxy
Machine: Ibm Xseries 305 (model 8673-62X)
Processor: Pentuim IV 2.6Ghz
Memory: 1 Go
Root Device: IDE, ata raid
Root Size/partition table: no partition
Output of lspci and lspci -n:
00:00.0 Host bridge: ServerWorks GCNB-LE Host Bridge (rev 32)
00:00.1 Host bridge: ServerWorks GCNB-LE Host Bridge
00:03.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
00:0f.0 ISA bridge: ServerWorks CSB5 South Bridge (rev 93)
00:0f.1 IDE interface: ServerWorks CSB5 IDE Controller (rev 93)
00:0f.2 USB Controller: ServerWorks OSB4/CSB5 OHCI USB Controller (rev
05)
00:0f.3 Host bridge: ServerWorks GCLE Host Bridge
00:10.0 Host bridge: ServerWorks: Unknown device 0101 (rev 05)
00:10.2 Host bridge: ServerWorks: Unknown device 0101 (rev 05)
01:02.0 RAID bus controller: CMD Technology Inc PCI0680 (rev 02)
02:04.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5703
Gigabit Ethernet (rev 02)
02:05.0 Ethernet controller: 00:00.0 Class 0600: 1166:0017 (rev 32)
00:00.1 Class 0600: 1166:0017
00:03.0 Class 0300: 1002:4752 (rev 27)
00:0f.0 Class 0601: 1166:0201 (rev 93)
00:0f.1 Class 0101: 1166:0212 (rev 93)
00:0f.2 Class 0c03: 1166:0220 (rev 05)
00:0f.3 Class 0600: 1166:0225
00:10.0 Class 0600: 1166:0101 (rev 05)
00:10.2 Class 0600: 1166:0101 (rev 05)
01:02.0 Class 0104: 1095:0680 (rev 02)
02:04.0 Class 0200: 14e4:16a7 (rev 02)
02:05.0 Class 0200: 14e4:16a7 (rev 02)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [E]
Partition hard drives: [ ]
Create file systems: [ ]
Mount partitions: [ ]
Install base system: [ ]
Install boot loader: [ ]
Reboot: [ ]
Comments/Problems:
There is an ata raid (LSI Megaraid 133) on the motherboard, the sarge
install didn't detect it, I want to use hardware read. If someone can
give me a hint to compile the module, or do make it work ....
Tks in Advance
Olivier Lechevalier
Euromed Marseille School Of Management
Reply to: