Bug#267457: installation-reports
Package: installation-reports
Debian-installer-version:
sarge RC1 from
(http://cdimage.debian.org/pub/cdimage-testing/sarge_d-i/i386/rc1/sarge-i386-businesscard.iso)
uname -a:
Linux debianhost 2.6.7-1-k7 #1 Thu Jul 8 06:45:35 EDT 2004 i686 GNU/Linux
Date:
2004-08-22 3:00PM GMT+8
Method:
Install with businessCard CD, boot with the CD. Install with command "linux26
noapic nolapic" since my laptop can't boot without these 2 words.
After the basic setup continue with these sourcelist:
http://ftp.debian.org
http://non-us.debian.org
Spend 2.30 hours+ for 456MB+ package downloaded.
Machine: Compaq Presario 700 laptop
Processor: AMD Duron 1.1GHz
Memory: 128MB PC133 so-dimm
Root Device: IDE
Root Size/partition table: <Feel free to paste the full partition
table, with notes on which partitions are mounted where.>
hda1-15GB NTFS WindowsXP
hda5-100MB FAT32
hda6-256MB SWAP
hda7-2.5GB EXT3 Debian
Output of lspci and lspci -n:
-----------------------------------------------------
"lspci"
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev
80)
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP]
0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South]
(rev 42)
0000:00:07.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
0000:00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 1a)
0000:00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev
40)
0000:00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97
Audio Controller (rev 50)
0000:00:09.0 Communication controller: Conexant HSF 56k HSFi Modem (rev 01)
0000:00:0a.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus
Controller (rev 01)
0000:00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
0000:01:00.0 VGA compatible controller: S3 Inc. VT8636A [ProSavage KN133] AGP4X
VGA Controller (TwisterK) (rev 01)
-----------------------------------------------------
lspci -n
0000:00:00.0 0600: 1106:0305 (rev 80)
0000:00:01.0 0604: 1106:8305
0000:00:07.0 0601: 1106:0686 (rev 42)
0000:00:07.1 0101: 1106:0571 (rev 06)
0000:00:07.2 0c03: 1106:3038 (rev 1a)
0000:00:07.4 0680: 1106:3057 (rev 40)
0000:00:07.5 0401: 1106:3058 (rev 50)
0000:00:09.0 0780: 14f1:2f00 (rev 01)
0000:00:0a.0 0607: 104c:ac50 (rev 01)
0000:00:0b.0 0200: 10ec:8139 (rev 10)
0000:01:00.0 0300: 5333:8d02 (rev 01)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [O]
Reboot: [O] with "noapic nolapic"
Comments/Problems:
I really enjoy the experience for this debian-installer even this is the first
time I install Debian, before this i had installed RedHat 8 and Knoppix.
During installation, I face some problems when i was downloading the package, it
will temp stop for about few minutes which i nearly going to re-install it
again.
After install it didn't show me with the correct VGA mode, my laptop can support
1024x768, but it force me to use 800x600, so I have to change it mannualy in
etc/X11/XF86Config-4
Btw, Good job :-) and thanks
--
Teck Khen
Reply to: