Bug#264113: installation-report
Package: installation-reports
Debian-installer-version:
sarge_d-i/i386/20040806/sarge-i386-netinst.iso
uname -a:
Linux weasel 2.6.7 #1 Fri Aug 6 23:58:04 EST 2004 i686 GNU/Linux
Date:
Fri Aug 6 13:00 2004
Method:
netinst cd, booted from cd, used 2.6 kernel. Additional packages
installed via apt-proxy from internal lan (apt-proxy points mainly at
mirror.aarnet.edu.au).
Machine:
Generic x86, Gigabyte 7VM400M-RZ motherboard, Northbridge VIA KM400,
Southbridge VIA 8235, On-Board VIA VT6103 (via-rhine) Lan.
Processor:
Athlon XP 1800
Memory:
256mb
Root Device:
IDE (On-Board VIA), ATA 133, Maxtor 40g hdd
Root Size/partition table:
Disk /dev/hda: 41.1 GB, 41110142976 bytes
255 heads, 63 sectors/track, 4998 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/hda1 * 1 2492 20016958+ 83 Linux
/dev/hda2 4936 4998 506047+ 82 Linux swap
/dev/hda3 2493 4935 19623397+ a6 OpenBSD
Output of lspci:
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8378 [KM400]
Chipset
Host Bridge
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge
0000:00:0b.0 Ethernet controller: Digital Equipment Corporation
DECchip 21041 [Tulip Pass 3] (rev 21)
0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 80)
0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 80)
0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 80)
0000:00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
0000:00:11.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
0000:00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102
[Rhine-II] (rev 74)
0000:01:00.0 VGA compatible controller: VIA Technologies, Inc. VT8378
[S3 UniChrome] Integrated Video (rev 01)
Base System Installation Checklist:
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [O]
Reboot: [O]
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Comments/Problems:
One of the most straight forward installers I have ever used, well
done!!
--
Stephen M. Gava <smig@debian.org>
Reply to: