Bug#224065: Package: installation-reports
Package: installation-reports
INSTALL REPORT
Debian-installer-version: http://www.mmweg.rwth-aachen.de/~sebastian.ley/d-i/netinst-image-i386/daily-2003-11-19/sarge-i386-netisnt.iso. The date on the file is 2003/11/22.
uname -a: Linux siegle 2.4.22-1-386 #9 Sat Oct 4 14:30:39 EST 2003 i686 GNU/Linux
Date: 2003/12/12 1:30 p.m. EST
Method: How did you install? A:net What did you boot off? A:cd If network
install, from where? A: carroll.aset.psu.edu Proxied? A: no
Machine: Dell precision 420 Service tag: H5115
Processor: PIII 733
Memory: 384MB
Root Device: 25GB IDE disk /dev/hda or /dev/ide/host0/bus0/target0/lun0/disc
Root Size/partition table:
Command (m for help): p
Disk /dev/hda: 27.3 GB, 27373731840 bytes
255 heads, 63 sectors/track, 3328 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/hda1 * 1 510 4096543+ b W95 FAT32
/dev/hda2 * 511 753 1951897+ 83 Linux <-----/
/dev/hda3 754 3282 20314192+ 83 Linux <-----/usr
/dev/hda4 3283 3328 369495 5 Extended
/dev/hda5 3283 3328 369463+ 82 Linux swap
Output of lspci:
siegle:~# lspci
00:00.0 Host bridge: Intel Corp. 82840 840 (Carmel) Chipset Host Bridge (Hub A) (rev 01)
00:01.0 PCI bridge: Intel Corp. 82840 840 (Carmel) Chipset AGP Bridge (rev 01)
00:1e.0 PCI bridge: Intel Corp. 82801AA PCI Bridge (rev 02)
00:1f.0 ISA bridge: Intel Corp. 82801AA ISA Bridge (LPC) (rev 02)
00:1f.1 IDE interface: Intel Corp. 82801AA IDE (rev 02)
00:1f.2 USB Controller: Intel Corp. 82801AA USB (rev 02)
00:1f.3 SMBus: Intel Corp. 82801AA SMBus (rev 02)
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 04)
02:04.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
02:06.0 Multimedia audio controller: Cirrus Logic CS 4614/22/24 [CrystalClear SoundFusion Audio Accelerator] (rev 01)
02:0e.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03)
03:0a.0 SCSI storage controller: Adaptec AIC-7899P U160/m (rev 01)
03:0a.1 SCSI storage controller: Adaptec AIC-7899P U160/m (rev 01)
Base System Installation Checklist:
Initial boot worked: [X]
Configure network HW: [X]
Config network: [X]
Detect CD: [X]
Load installer modules: [X]
Detect hard drives: [X]
Partition hard drives: [E]
Create file systems: [X]
Mount partitions: [X]
Install base system: [X]
Install boot loader: [X]
Reboot: [X]
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Partition hard drive: It was probably just me, but I could not figure out how
to make an extended partition with logical partitions inside of it using cfdisk.
Comments/Problems:
<Description of the install, in prose, and any thoughts, comments
and ideas you had during the initial install.>
Install was simple. Wrote the ISO to cd, booted the cd. It found all my hardware. I pointed it to carroll.aset.psu.edu and away it went.
Questions/comments:
When I run lilo I get this message and am unsure of what I should do to solve this:
siegle:~# lilo
Warning: '/proc/partitions' does not match '/dev' directory structure.
Name change: '/dev/ide/host0/bus0/target0/lun0/disc' -> '/dev/hda'
The kernel was compiled with DEVFS_FS, but 'devfs=mount' was omitted
as a kernel command-line boot parameter; hence, the '/dev' directory
structure does not reflect DEVFS_FS device names.
Added Linux *
-Jonathan
Reply to: