Hello Lennart,Thank you so much for your reply. I think I did a follow up post on this and I also posted a message to debian-user which is copied below with lots of details on the system. more below ...
Lennart Sorensen wrote:
On Fri, Dec 30, 2005 at 01:43:07PM -0500, Stephen Woodbridge wrote:I'm trying to install on a Supermicro X6DHT-G motherboard system with 2 EM64T processors, using a CD built from debian-31r0a-amd64-netinst.isoThe system boots to the CD and starts the installer, but it can not find a driver for the CD-ROM. The CD-ROM is on IDE Channel 1 Slave and IDE Channel 0 Master is a 250GB SATA1 drive.The Installer complains about unavailable modules: e1000 ide-mod ide-probe-mod ide-detect ide-floppy Any ideas how to work around this problem?What is the chipset on that board? It may simply be too new for the 2.6.8 / 2.4.27 kernel in sarge. Which did you boot with? Default is 2.4.27, if you boot with linux26 it uses 2.6 kernel which tends to work better. Using an installer with 2.6.12 might work better too.
Tried the installers from: sarge i386 sarge amd64 etch amd64 etch amd64 (daily) All of these exhibited the same problem. See below ...
Making sure the bios setting has the SATA controller in native mode also tends to help, since combined/emulated ide mode tends to screw up the pata ports under linux when the sata driver loads. Len Sorensen
------------- posted on debian-user --------------------------- Hi all,I have a new Supermicro X6DHT-G motherboard based system and I'm have a problem with it recognizing the CD ROM drive. The CD ROM is PATA device that appears to be handled via an Intel Corp. 6300ESB chip probably using the IDE SATA controller and some PATA to SATA interface.
The Debian installer fails to detect the CD ROM If I going into expert mode in the installer and select ONLY generic, ide-generic, ide-cd, and isofs modulesthen it recognizes the CD ROM and I can get on with the install, but after the reboot the CD ROM vanishes again.
I have been able to replicate this with: sarge i386 sarge amd64 <<<< installed this after using trick above etch amd64 etch amd64 2005-12-31 daily Debian Installers. My BIOS reports IDE Channel 0 Master 250GB SATA1 IDE Channel 1 Slave CD-ROMI spend 16 hours just getting Debian installed, but I'm at a lose as to how to fix this problem or how to report a bug against it.
Other info that might help diagnose this issue: woodbri@carto:~$ lsmod Module Size Used by i2c_dev 13824 0 ipv6 280552 20 w83627hf 30980 0 w83781d 36608 0 i2c_sensor 4352 2 w83627hf,w83781d i2c_isa 3840 0 i2c_i801 9748 0i2c_core 27008 6 i2c_dev,w83627hf,w83781d,i2c_sensor,i2c_isa,i2c_i801
ext3 121616 5 jbd 64176 1 ext3 mbcache 11400 1 ext3 tsdev 9472 0 mousedev 12628 0 evdev 11648 0 psmouse 20108 0 genrtc 11516 0 dm_mod 58464 0 sd_mod 22400 7 ide_disk 21504 0 pdc202xx_new 12748 0 aec62xx 12492 0 alim15x3 13592 0 amd74xx 15536 0 atiixp 10656 0 cmd64x 13772 0 cs5520 8208 0 cs5530 8720 0 cy82c693 6536 0 hpt34x 7424 0 ns87415 6316 0 opti621 6404 0 pdc202xx_old 18252 0 piix 15692 0 rz1000 4480 0 sc1200 10640 0 serverworks 14116 0 siimage 14464 0 sis5513 16272 0 slc90e66 10512 0 triflex 7176 0 trm290 6276 0 via82cxxx 14512 0 floppy 65104 0 usb_storage 69184 0 e1000 83588 0 ide_cd 42784 0 cdrom 39848 1 ide_cd ide_generic 2816 0 generic 6528 0ide_core 154688 28 ide_disk,pdc202xx_new,aec62xx,alim15x3,amd74xx,atiixp,cmd64x,cs5520,cs5530,cy82c693,hpt34x,ns87415,opti621,pdc202xx_old,piix,rz1000,sc1200,serverworks,siimage,sis5513,slc90e66,triflex,trm290,via82cxxx,usb_storage,ide_cd,ide_generic,generic
fbcon 32164 70 vga16fb 14464 1 vgastate 10240 1 vga16fb usbserial 33008 0 usbkbd 8960 0 ehci_hcd 32132 0 uhci_hcd 33056 0 thermal 15116 0 processor 15224 1 thermal fan 5512 0 ata_piix 9988 6 libata 42888 1 ata_piix scsi_mod 131072 3 sd_mod,usb_storage,libata unix 32032 16 font 10112 1 fbcon vesafb 7984 0 cfbcopyarea 5120 2 vga16fb,vesafb cfbimgblt 4352 2 vga16fb,vesafb cfbfillrect 5248 2 vga16fb,vesafb woodbri@carto:~$ lspci 0000:00:00.0 Host bridge: Intel Corp. Server Memory Controller Hub (rev 0c)0000:00:00.1 ff00: Intel Corp. Memory Controller Hub Error Reporting Register (rev 0c) 0000:00:01.0 System peripheral: Intel Corp. Memory Controller Hub DMA Controller (rev 0c) 0000:00:02.0 PCI bridge: Intel Corp. Memory Controller Hub PCI Express Port A0 (rev 0c) 0000:00:04.0 PCI bridge: Intel Corp. Memory Controller Hub PCI Express Port B0 (rev 0c) 0000:00:06.0 PCI bridge: Intel Corp. Memory Controller Hub PCI Express Port C0 (rev 0c)
0000:00:1c.0 PCI bridge: Intel Corp. 6300ESB 64-bit PCI-X Bridge (rev 02)0000:00:1d.0 USB Controller: Intel Corp. 6300ESB USB Universal Host Controller (rev 02) 0000:00:1d.1 USB Controller: Intel Corp. 6300ESB USB Universal Host Controller (rev 02)
0000:00:1d.4 System peripheral: Intel Corp. 6300ESB Watchdog Timer (rev 02)0000:00:1d.5 PIC: Intel Corp. 6300ESB I/O Advanced Programmable Interrupt Controller (rev 02) 0000:00:1d.7 USB Controller: Intel Corp. 6300ESB USB2 Enhanced Host Controller (rev 02)
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 0a)0000:00:1f.0 ISA bridge: Intel Corp. 6300ESB LPC Interface Controller (rev 02) 0000:00:1f.2 IDE interface: Intel Corp. 6300ESB SATA Storage Controller (rev 02)
0000:00:1f.3 SMBus: Intel Corp. 6300ESB SMBus Controller (rev 02) 0000:01:00.0 PCI bridge: Intel Corp. PCI Bridge Hub A (rev 09)0000:01:00.1 PIC: Intel Corp. PCI Bridge Hub I/OxAPIC Interrupt Controller A (rev 09)
0000:01:00.2 PCI bridge: Intel Corp. PCI Bridge Hub B (rev 09)0000:01:00.3 PIC: Intel Corp. PCI Bridge Hub I/OxAPIC Interrupt Controller B (rev 09)
0000:03:02.0 RAID bus controller: 3ware Inc: Unknown device 10030000:06:01.0 Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller (rev 05) 0000:06:02.0 Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller (rev 05) 0000:07:01.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
woodbri@carto:~$ lsscsi [0:0:0:0] disk ATA WDC WD2500JS-00N 10.0 /dev/sda woodbri@carto:~$ dmesg Bootdata ok (command line is root=/dev/sda1 ro console=tty0 )Linux version 2.6.8-11-em64t-p4-smp (root@athlon) (gcc version 3.4.4 20050314 (prerelease) (Debian 3.4.3-13)) #1 SMP Mon Oct 3 00:07:51 CEST 2005
BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009b000 (usable) BIOS-e820: 000000000009b000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000007ff70000 (usable) BIOS-e820: 000000007ff70000 - 000000007ff78000 (ACPI data) BIOS-e820: 000000007ff78000 - 000000007ff80000 (ACPI NVS) BIOS-e820: 000000007ff80000 - 0000000080000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved) BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved) No mptable found. On node 0 totalpages: 524144 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 520048 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1ACPI: RSDP (v000 PTLTD ) @ 0x00000000000f5d60 ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x000000007ff72fc7 ACPI: FADT (v001 INTEL LINDHRST 0x06040000 PTL 0x00000003) @ 0x000000007ff77e2c ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x000000007ff77ea0 ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x000000007ff77f48 ACPI: SPCR (v001 PTLTD $UCRTBL$ 0x06040000 PTL 0x00000001) @ 0x000000007ff77f70 ACPI: MCFG (v001 PTLTD MCFG 0x06040000 LTP 0x00000000) @ 0x000000007ff77fc0 ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20030224) @ 0x000000007ff73003 ACPI: DSDT (v001 Intel LINDHRST 0x06040000 MSFT 0x0100000e) @ 0x0000000000000000
ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:4 APIC version 16 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x06] enabled) Processor #6 15:4 APIC version 16 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 15:4 APIC version 16 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x07] enabled) Processor #7 15:4 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: Assigned apic_id 2 IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: IOAPIC (id[0x03] address[0xfec10000] gsi_base[24]) IOAPIC[1]: Assigned apic_id 3 IOAPIC[1]: apic_id 3, version 32, address 0xfec10000, GSI 24-47 ACPI: IOAPIC (id[0x04] address[0xfec80000] gsi_base[48]) IOAPIC[2]: Assigned apic_id 4 IOAPIC[2]: apic_id 4, version 32, address 0xfec80000, GSI 48-71 ACPI: IOAPIC (id[0x05] address[0xfec80400] gsi_base[72]) IOAPIC[3]: Assigned apic_id 5 IOAPIC[3]: apic_id 5, version 32, address 0xfec80400, GSI 72-95 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Using ACPI (MADT) for SMP configuration information Built 1 zonelists Kernel command line: root=/dev/sda1 ro console=tty0 Initializing CPU#0 PID hash table entries: 16 (order 4: 256 bytes) time.c: Using 1.193182 MHz PIT timer. time.c: Detected 3000.283 MHz processor. Console: colour VGA+ 80x25 Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)Memory: 2053248k/2096576k available (1606k kernel code, 42524k reserved, 912k data, 152k init)
Calibrating delay loop... 5931.00 BogoMIPS
Security Scaffold v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
CPU: Trace cache: 12K uops
using mwait in idle threads.
CPU: Physical Processor ID: 0
Using IO APIC NMI watchdog
CPU: Trace cache: 12K uops
CPU: Physical Processor ID: 0
CPU0: Intel(R) Xeon(TM) CPU 3.00GHz stepping 03
per-CPU timeslice cutoff: 0.00 usecs.
task migration cache decay timeout: 1 msecs.
Booting processor 1/6 rip 6000 rsp 10003267f58
Initializing CPU#1
Calibrating delay loop... 5996.54 BogoMIPS
CPU: Trace cache: 12K uops
CPU: Physical Processor ID: 3
Intel(R) Xeon(TM) CPU 3.00GHz stepping 03
Booting processor 2/1 rip 6000 rsp 1007fa9ff58
Initializing CPU#2
Calibrating delay loop... 5996.54 BogoMIPS
CPU: Trace cache: 12K uops
CPU: Physical Processor ID: 0
Intel(R) Xeon(TM) CPU 3.00GHz stepping 03
Booting processor 3/7 rip 6000 rsp 1007fa17f58
Initializing CPU#3
Calibrating delay loop... 5996.54 BogoMIPS
CPU: Trace cache: 12K uops
CPU: Physical Processor ID: 3
Intel(R) Xeon(TM) CPU 3.00GHz stepping 03
Total of 4 processors activated (23920.64 BogoMIPS).
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22,
2-23, 3-0, 3-1, 3-2, 3-3, 3-4, 3-5, 3-6, 3-7, 3-8, 3-9, 3-10, 3-11,
3-12, 3-13, 3-14, 3-15, 3-16, 3-17, 3-18, 3-19, 3-20, 3-21, 3-22, 3-23,
4-0, 4-1, 4-2, 4-3, 4-4, 4-5, 4-6, 4-7, 4-8, 4-9, 4-10, 4-11, 4-12,
4-13, 4-14, 4-15, 4-16, 4-17, 4-18, 4-19, 4-20, 4-21, 4-22, 4-23, 5-0,
5-1, 5-2, 5-3, 5-4, 5-5, 5-6, 5-7, 5-8, 5-9, 5-10, 5-11, 5-12, 5-13,
5-14, 5-15, 5-16, 5-17, 5-18, 5-19, 5-20, 5-21, 5-22, 5-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1 activating NMI Watchdog ... done. testing NMI watchdog ... OK. Using local APIC timer interrupts. Detected 12.501 MHz APIC timer. checking TSC synchronization across 4 CPUs: passed. time.c: Using PIT/TSC based timekeeping. Brought up 4 CPUs CPU0: online domain 0: span 05 groups: 01 04 domain 1: span 0f groups: 05 0a CPU1: online domain 0: span 0a groups: 02 08 domain 1: span 0f groups: 0a 05 CPU2: online domain 0: span 05 groups: 04 01 domain 1: span 0f groups: 05 0a CPU3: online domain 0: span 0a groups: 08 02 domain 1: span 0f groups: 0a 05checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
NET: Registered protocol family 16 PCI: Using configuration type 1 PCI: Using MMCONFIG at e0000000 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040326 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0.PXH0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0.PXH1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEY0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEZ0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIX._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 6 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *10 11 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 6 7 10 *11 14 15) usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing IOAPIC[0]: Set PCI routing entry (2-16 -> 0xa9 -> IRQ 16 Mode:1 Active:1) ACPI: PCI interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16 ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16 ACPI: PCI interrupt 0000:00:04.0[A] -> GSI 16 (level, low) -> IRQ 16 ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 16 (level, low) -> IRQ 16 ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16 IOAPIC[0]: Set PCI routing entry (2-19 -> 0xb1 -> IRQ 19 Mode:1 Active:1) ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19 IOAPIC[0]: Set PCI routing entry (2-23 -> 0xb9 -> IRQ 23 Mode:1 Active:1) ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23 IOAPIC[0]: Set PCI routing entry (2-18 -> 0xc1 -> IRQ 18 Mode:1 Active:1) ACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 18 IOAPIC[0]: Set PCI routing entry (2-17 -> 0xc9 -> IRQ 17 Mode:1 Active:1) ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 17 IOAPIC[3]: Set PCI routing entry (5-0 -> 0xd1 -> IRQ 72 Mode:1 Active:1) ACPI: PCI interrupt 0000:03:02.0[A] -> GSI 72 (level, low) -> IRQ 72 IOAPIC[1]: Set PCI routing entry (3-0 -> 0xd9 -> IRQ 24 Mode:1 Active:1) ACPI: PCI interrupt 0000:06:01.0[A] -> GSI 24 (level, low) -> IRQ 24 IOAPIC[1]: Set PCI routing entry (3-1 -> 0xe1 -> IRQ 25 Mode:1 Active:1) ACPI: PCI interrupt 0000:06:02.0[A] -> GSI 25 (level, low) -> IRQ 25 ACPI: PCI interrupt 0000:07:01.0[A] -> GSI 16 (level, low) -> IRQ 16 number of MP IRQ sources: 15. number of IO-APIC #2 registers: 24. number of IO-APIC #3 registers: 24. number of IO-APIC #4 registers: 24. number of IO-APIC #5 registers: 24. testing the IO APIC....................... IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 .... register #01: 00178020 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0020 .... register #02: 00178020 ....... : arbitration: 00 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 001 01 0 0 0 0 0 1 1 39 02 001 01 0 0 0 0 0 1 1 31 03 001 01 0 0 0 0 0 1 1 41 04 001 01 0 0 0 0 0 1 1 49 05 001 01 0 0 0 0 0 1 1 51 06 001 01 0 0 0 0 0 1 1 59 07 001 01 0 0 0 0 0 1 1 61 08 001 01 0 0 0 0 0 1 1 69 09 001 01 0 1 0 0 0 1 1 71 0a 001 01 0 0 0 0 0 1 1 79 0b 001 01 0 0 0 0 0 1 1 81 0c 001 01 0 0 0 0 0 1 1 89 0d 001 01 0 0 0 0 0 1 1 91 0e 001 01 0 0 0 0 0 1 1 99 0f 001 01 0 0 0 0 0 1 1 A1 10 001 01 1 1 0 1 0 1 1 A9 11 001 01 1 1 0 1 0 1 1 C9 12 001 01 1 1 0 1 0 1 1 C1 13 001 01 1 1 0 1 0 1 1 B1 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 001 01 1 1 0 1 0 1 1 B9 IO APIC #3...... .... register #00: 03000000 ....... : physical APIC id: 03 .... register #01: 00178020 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0020 .... register #02: 00178020 ....... : arbitration: 00 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 001 01 1 1 0 1 0 1 1 D9 01 001 01 1 1 0 1 0 1 1 E1 02 000 00 1 0 0 0 0 0 0 00 03 000 00 1 0 0 0 0 0 0 00 04 000 00 1 0 0 0 0 0 0 00 05 000 00 1 0 0 0 0 0 0 00 06 000 00 1 0 0 0 0 0 0 00 07 000 00 1 0 0 0 0 0 0 00 08 000 00 1 0 0 0 0 0 0 00 09 000 00 1 0 0 0 0 0 0 00 0a 000 00 1 0 0 0 0 0 0 00 0b 000 00 1 0 0 0 0 0 0 00 0c 000 00 1 0 0 0 0 0 0 00 0d 000 00 1 0 0 0 0 0 0 00 0e 000 00 1 0 0 0 0 0 0 00 0f 000 00 1 0 0 0 0 0 0 00 10 000 00 1 0 0 0 0 0 0 00 11 000 00 1 0 0 0 0 0 0 00 12 000 00 1 0 0 0 0 0 0 00 13 000 00 1 0 0 0 0 0 0 00 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00 IO APIC #4...... .... register #00: 04000000 ....... : physical APIC id: 04 .... register #01: 00178020 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0020 .... register #02: 04000000 ....... : arbitration: 04 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 000 00 1 0 0 0 0 0 0 00 02 000 00 1 0 0 0 0 0 0 00 03 000 00 1 0 0 0 0 0 0 00 04 000 00 1 0 0 0 0 0 0 00 05 000 00 1 0 0 0 0 0 0 00 06 000 00 1 0 0 0 0 0 0 00 07 000 00 1 0 0 0 0 0 0 00 08 000 00 1 0 0 0 0 0 0 00 09 000 00 1 0 0 0 0 0 0 00 0a 000 00 1 0 0 0 0 0 0 00 0b 000 00 1 0 0 0 0 0 0 00 0c 000 00 1 0 0 0 0 0 0 00 0d 000 00 1 0 0 0 0 0 0 00 0e 000 00 1 0 0 0 0 0 0 00 0f 000 00 1 0 0 0 0 0 0 00 10 000 00 1 0 0 0 0 0 0 00 11 000 00 1 0 0 0 0 0 0 00 12 000 00 1 0 0 0 0 0 0 00 13 000 00 1 0 0 0 0 0 0 00 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00 IO APIC #5...... .... register #00: 05000000 ....... : physical APIC id: 05 .... register #01: 00178020 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0020 .... register #02: 05000000 ....... : arbitration: 05 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 001 01 1 1 0 1 0 1 1 D1 01 000 00 1 0 0 0 0 0 0 00 02 000 00 1 0 0 0 0 0 0 00 03 000 00 1 0 0 0 0 0 0 00 04 000 00 1 0 0 0 0 0 0 00 05 000 00 1 0 0 0 0 0 0 00 06 000 00 1 0 0 0 0 0 0 00 07 000 00 1 0 0 0 0 0 0 00 08 000 00 1 0 0 0 0 0 0 00 09 000 00 1 0 0 0 0 0 0 00 0a 000 00 1 0 0 0 0 0 0 00 0b 000 00 1 0 0 0 0 0 0 00 0c 000 00 1 0 0 0 0 0 0 00 0d 000 00 1 0 0 0 0 0 0 00 0e 000 00 1 0 0 0 0 0 0 00 0f 000 00 1 0 0 0 0 0 0 00 10 000 00 1 0 0 0 0 0 0 00 11 000 00 1 0 0 0 0 0 0 00 12 000 00 1 0 0 0 0 0 0 00 13 000 00 1 0 0 0 0 0 0 00 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ16 -> 0:16 IRQ17 -> 0:17 IRQ18 -> 0:18 IRQ19 -> 0:19 IRQ23 -> 0:23 IRQ24 -> 1:0 IRQ25 -> 1:1 IRQ72 -> 3:0 .................................... done. Simple Boot Flag at 0x39 set to 0x1 IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x0 Initializing Cryptographic API Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 input: AT Translated Set 2 keyboard on isa0060/serio0 NET: Registered protocol family 2 IP: routing cache hash table of 8192 buckets, 128Kbytes TCP: Hash tables configured (established 262144 bind 65536) NET: Registered protocol family 8 NET: Registered protocol family 20 ACPI: (supports S0 S1 S4 S5) RAMDISK: cramfs filesystem found at block 0 RAMDISK: Loading 4300 blocks [1 disk] into ram disk... done. VFS: Mounted root (cramfs filesystem) readonly. Freeing unused kernel memory: 152k freed vesafb: probe of vesafb0 failed with error -6 NET: Registered protocol family 1 SCSI subsystem initialized libata version 1.02 loaded. ata_piix version 1.02 ata_piix: combined mode detected ACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1f.2 to 64 ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x1470 irq 14ata1: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:207f
ata1: dev 0 ATA, max UDMA/133, 488397168 sectors: lba48 ata1: dev 0 configured for UDMA/133 scsi0 : ata_piix Using anticipatory io scheduler Vendor: ATA Model: WDC WD2500JS-00N Rev: 10.0 Type: Direct-Access ANSI SCSI revision: 05 ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0x1478 irq 15ata2: dev 1 cfg 49:0f00 82:4210 83:4000 84:4000 85:0000 86:0000 87:4000 88:0407
ata2: dev 1 ATAPI, max UDMA/33 ata2: dev 1 configured for UDMA/33 scsi1 : ata_piix ACPI: Processor [CPU0] (supports C1) ACPI: Processor [CPU1] (supports C1) ACPI: Processor [CPU2] (supports C1) ACPI: Processor [CPU3] (supports C1) USB Universal Host Controller Interface driver v2.2 ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16 uhci_hcd 0000:00:1d.0: Intel Corp. 6300ESB USB Universal Host Controller PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: irq 16, io base 0000000000001400 uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19 uhci_hcd 0000:00:1d.1: Intel Corp. 6300ESB USB Universal Host Controller PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: irq 19, io base 0000000000001420 uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23 ehci_hcd 0000:00:1d.7: Intel Corp. 6300ESB USB2 Enhanced Host Controller PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: irq 23, pci mem ffffff0010018400 ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 3 PCI: cache line size of 128 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 hub 3-0:1.0: USB hub found hub 3-0:1.0: 4 ports detected usbcore: registered new driver usbkbd drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic usbcore: registered new driver usbserial_generic usbcore: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0 vga16fb: initializing vga16fb: mapped to 0x00000100000a0000 fb0: VGA16 VGA frame buffer device Console: switching to colour frame buffer device 80x30 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ide0: I/O resource 0x1F0-0x1F7 not free. ide0: ports already in use, skipping probe ide1: I/O resource 0x170-0x177 not free. ide1: ports already in use, skipping probe e1000: Ignoring new-style parameters in presence of obsolete ones Intel(R) PRO/1000 Network Driver - version 5.2.52-k4 Copyright (c) 1999-2004 Intel Corporation. ACPI: PCI interrupt 0000:06:01.0[A] -> GSI 24 (level, low) -> IRQ 24 e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection ACPI: PCI interrupt 0000:06:02.0[A] -> GSI 25 (level, low) -> IRQ 25 e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. inserting floppy driver for 2.6.8-11-em64t-p4-smp Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) SCSI device sda: drive cache: write back /dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 > Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com Generic RTC Driver v1.07 input: ImPS/2 Generic Wheel Mouse on isa0060/serio1 mice: PS/2 mouse device common for all mice ts: Compaq touchscreen protocol output kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Adding 6024332k swap on /dev/sda7. Priority:-1 extents:1 EXT3 FS on sda1, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on sda9, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda8, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda5, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda6, internal journal EXT3-fs: mounted filesystem with ordered data mode. hw_random: RNG not detected e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex NET: Registered protocol family 10 Disabled Privacy Extensions on device ffffffff8033e840(lo) IPv6 over IPv4 tunneling driver eth0: no IPv6 routers present i2c /dev entries driver --