Re: dvd+rw-tools-5.14.4.7.4.tar.gz
Hi Andy,
switching the system off, waiting some hours and trying
again, I didn't got the "unsupported MMC" message again.
only the speed flag didn't work. Nevertheless I tried
again to burn and it burned. Now mediainfo doesn't say
"blank" but when I try to mount it failes and "dmesg"
gives:
SCSI cdrom error : host 0 channel 0 id 0 lun 0 return code = 28000000
Current sd0b:00: sns = 70 4
ASC=3e ASCQ= 2
Raw sense data:0x70 0x00 0x04 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00
0x3e 0x02 0x00 0x00 0x00 0x00 I/O error: dev 0b:00, sector 0
[..]
strange.. any ideas?
cu
rasca
On Sat, 13 Dec 2003 12:07:32 +0100
Rasca <rasca@gmx.de> wrote:
>
> I found out that there is a firmware update to version 47
> (original: 40). But after updating I see:
>
> rasca@lupo:~/pictures> growisofs -speed=1 -Z /dev/scd0=fotos-backup.iso
> :-( /dev/scd0: unsupported MMC profile 10
> rasca@lupo:~/pictures>
>
> does it mean I have to downgrade my firmware or upgrade my software
> (or kernel..)?
>
>
> On Fri, 12 Dec 2003 22:47:17 +0100
> Rasca <rasca@gmx.de> wrote:
>
> >
> > On Thu, 11 Dec 2003 20:12:27 +0100
> > Andy Polyakov <appro@fy.chalmers.se> wrote:
> >
> > > > This was fine. But after burning my first DVD I had a problem.
> > > > May be you know the answer.
> > > >
> > > > My setup: BTC DVD+/-R/RW, Linux kernel 2.4.22, cdrecord 2.x
> > > >
> > > > Burning was done by
> > > > growisofs -Z /dev/scd0=fuji.iso
> > > >
> > > > No errors or warning were given. But then if I try to
> > > > mount it is see:
> > > >
> > > > attempt to access beyond end of device
> > > > 0b:00: rw=0, want=34, limit=2
> > > > isofs_read_super: bread failed, dev=0b:00, iso_blknum=16, block=16
> > > >
> > > > dvd+rw-mediainfo gives:
> > > > INQUIRY: [DVDRW ][IDE1004 ][0040]
> > > > GET [CURRENT] CONFIGURATION:
> > > > Mounted Media: 11h, DVD-R Sequential
> > > > Media ID: LD01
> > > > Current Write Speed: 4.0x1385=5540KB/s
> > > > Write Speed #0: 4.0x1385=5540KB/s
> > > > Write Speed #1: 2.0x1385=2770KB/s
> > > > Write Speed #2: 1.0x1385=1385KB/s
> > > > GET PERFORMANCE:
> > > > Speed Descriptor#0: 00/2298496 Reading@1.0x Writing@4.0x
> > > > READ DVD STRUCTURE[#10h]:
> > > > Media Book Type: 25h, DVD-R book [revision 5]
> > > > Legacy lead-out at: 2298496*2KB=4707319808
> > > > READ DVD STRUCTURE[#0h]:
> > > > Media Book Type: 25h, DVD-R book [revision 5]
> > > > Last border-out at: 0*2KB=0
> > > > READ DISC INFORMATION:
> > > > Disc status: blank
> > > > Number of Sessions: 1
> > > > State of Last Session: empty
> > > > Number of Tracks: 1
> > > > READ TRACK INFORMATION[#1]:
> > > > Track State: blank
> > > > Track Start Address: 0*2KB
> > > > Next Writable Address: 0*2KB
> > > > Free Blocks: 2298496*2KB
> > > > Track Size: 2298496*2KB
> > > >
> > > > A disk status of blank!? strange.. If I have a look
> > > > at the surface of the dvd it looks burned..
> > > >
> > > > Any ideas?
> > >
> > > Smells like media poorly supported by your firmware. I mean if surface
> > > hue has changed and unit still recognizes media as blank, it sounds like
> > > laser power was not enough during recording. You should a) try another
> > > media brand, b) try to record at lower speed. As for the latter. Version
> > > 5.14 introduces new speed selection code and given the dvd+rw-medainfo
> > > output, it might fail. Problem is that units presents several "Write
> > > Speed" descriptors, but only one "Performance" descriptor. This means
> > > that you might have to use previous version 5.13 at least with this
> > > media. I'd like to hear more about your experience with this [preferably
> > > on the list]. A.
> >
> > I went back to 5.13 and used a slower speed. But I failed again:
> >
> > rasca@lupo:~/pictures> growisofs -Z /dev/scd0=fotos-backup.iso -speed=1
> > Executing 'builtin_dd if=fotos-backup.iso of=/dev/scd0 obs=32k seek=0'
> > :-[ Failed to change write speed: 2770->1385
> >
> > rasca@lupo:~/pictures> growisofs -Z /dev/scd0=fotos-backup.iso -speed=2
> > Executing 'builtin_dd if=fotos-backup.iso of=/dev/scd0 obs=32k seek=0'
> > /dev/scd0: "Current Write Speed" is 2.0x1385KBps.
> > 7864320/1610125312 ( 0.5%) @1.7x, remaining 20:22
> > 7864320/1610125312 ( 0.5%) @0.0x, remaining 30:33
> > 7864320/1610125312 ( 0.5%) @0.0x, remaining 44:08
> > 7864320/1610125312 ( 0.5%) @0.0x, remaining 54:19
> > 7864320/1610125312 ( 0.5%) @0.0x, remaining 67:54
> > 7864320/1610125312 ( 0.5%) @0.0x, remaining 78:05
> > 7864320/1610125312 ( 0.5%) @0.0x, remaining 88:17
> > 7864320/1610125312 ( 0.5%) @0.0x, remaining 101:52
> > 7864320/1610125312 ( 0.5%) @0.0x, remaining 112:03
> > 7864320/1610125312 ( 0.5%) @0.0x, remaining 125:38
> > :-[ LBA=f00h, SENSE KEY=5h/ASC=21h/ASCQ=02h ]
> > :-( write failed: Input/output error
> > /dev/scd0: flushing cache
> > /dev/scd0: updating RMA
> > /dev/scd0: closing session
> > rasca@lupo:~/pictures>
> >
> > and "dmesg" says:
> >
> > scsi : aborting command due to timeout : pid 37928, scsi0, channel 0, id
> > 0, lun 0 0x2a 00 00 00 0f 00 00 00 10 00
> > hdc: irq timeout: status=0xd0 { Busy }
> > hdc: ATAPI reset complete
> > hdc: irq timeout: status=0xc0 { Busy }
> > hdc: ATAPI reset complete
> > hdc: irq timeout: status=0xc0 { Busy }
> > scsi0 channel 0 : resetting for second half of retries.
> > SCSI bus is being reset for host 0 channel 0.
> >
> >
> >
> > --
> > Welchen Unterschied macht es für die Toten, die Waisen und die
> > Heimatlosen, ob irrsinnige Vernichtung im Namen der Diktatur oder im
> > heiligen Namen der Freiheit und Demokratie geschieht? - Gandhi -
>
>
> --
> Welchen Unterschied macht es für die Toten, die Waisen und die Heimatlosen,
> ob irrsinnige Vernichtung im Namen der Diktatur oder im heiligen Namen der
> Freiheit und Demokratie geschieht? - Gandhi -
--
Welchen Unterschied macht es für die Toten, die Waisen und die Heimatlosen,
ob irrsinnige Vernichtung im Namen der Diktatur oder im heiligen Namen der
Freiheit und Demokratie geschieht? - Gandhi -
Reply to: