Dear MIPS porters, DSA would like to upgrade the remaining mips*el buildds to bullseye (and later to bookworm), however we have trouble running the Bullseye or Bookworm kernel on the LS3A-RS780-1w ones. Both Bullseye and Bookworm kernels boot fine up to the userland, but the network card does not work. It *seems* to an interrupt issue as the corresponding counter in /proc/interrupts does not change, and in addition the kernel logs show the following warnings: [ 5.077846] pcieport 0000:00:02.0: of_irq_parse_pci: failed with rc=-22 [ 5.084744] pcieport 0000:00:03.0: of_irq_parse_pci: failed with rc=-22 [ 5.170772] ahci 0000:00:11.0: of_irq_parse_pci: failed with rc=-22 [ 7.376554] pci 0000:00:07.0: of_irq_parse_pci: failed with rc=-22 [ 7.444769] ata_generic 0000:00:14.1: of_irq_parse_pci: failed with rc=-22 [ 7.495993] ehci-pci 0000:00:12.2: of_irq_parse_pci: failed with rc=-22 [ 7.624868] ehci-pci 0000:00:13.2: of_irq_parse_pci: failed with rc=-22 [ 7.753230] ohci-pci 0000:00:12.0: of_irq_parse_pci: failed with rc=-22 [ 7.886362] ohci-pci 0000:00:12.1: of_irq_parse_pci: failed with rc=-22 [ 8.018045] ohci-pci 0000:00:13.0: of_irq_parse_pci: failed with rc=-22 [ 8.150168] ohci-pci 0000:00:13.1: of_irq_parse_pci: failed with rc=-22 [ 8.294391] ohci-pci 0000:00:14.5: of_irq_parse_pci: failed with rc=-22 [ 18.398222] snd_hda_intel 0000:00:14.2: of_irq_parse_pci: failed with rc=-22 [ 18.547932] pci 0000:00:01.0: of_irq_parse_pci: failed with rc=-22 Any idea how to solve this issue? I have attached a full 6.1 kernel boot log for reference. Thanks, Aurelien -- Aurelien Jarno GPG: 4096R/1DDD8C9B aurelien@aurel32.net http://aurel32.net
Linux version 6.1.0-0.deb11.5-loongson-3 (debian-kernel@lists.debian.org) (gcc-10 (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Debian 6.1.12-1~bpo11+1 (2023-03-05)
CpuClock = 900000000
The bridge chip is RS780E or SR5690
CP0_Config3: CP0 16.3 (0xa0)
CP0_PageGrain: CP0 5.1 (0x20000000)
NUMA: Discovered 4 cpus on 1 nodes
Node0: mem_type:1, mem_start:0x200000, mem_size:0xee MB
start_pfn:0x80, end_pfn:0x3c00, num_physpages:0x3b80
Node0: mem_type:2, mem_start:0x90000000, mem_size:0x6e0 MB
start_pfn:0x24000, end_pfn:0x3f800, num_physpages:0x1f380
Node0: mem_type:2, mem_start:0x100000000, mem_size:0x1800 MB
start_pfn:0x40000, end_pfn:0xa0000, num_physpages:0x7f380
Node0's addrspace_offset is 0x0
Node0: start_pfn=0x80, end_pfn=0xa0000
NUMA: set cpumask cpu 0 on node 0
NUMA: set cpumask cpu 1 on node 0
NUMA: set cpumask cpu 2 on node 0
NUMA: set cpumask cpu 3 on node 0
printk: bootconsole [early0] enabled
CPU0 revision is: 00006305 (ICT Loongson-3)
FPU revision is: 00770501
MIPS: machine is loongson,loongson64c-4core-rs780e
Initial ramdisk at: 0x9800000004000000 (30712541 bytes)
software IO TLB: area num 1.
software IO TLB: mapped [mem 0x0000000005d4c000-0x0000000009d4c000] (64MB)
SMBIOS 2.6 present.
DMI: Loongson Loongson-3A5-780E-1w-V1.1-demo/Loongson-3A5-780E-1w-V1.1-demo, BIOS Loongson-PMON-V3.3-20141015 10/15/2014
Detected 4 available CPU(s)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 64kB, 4-way, VIPT, no aliases, linesize 32 bytes
Unified victim cache 0kB direct mapped, linesize 0 bytes.
Unified secondary cache 4096kB 4-way, linesize 32 bytes.
Zone ranges:
DMA32 [mem 0x0000000000200000-0x00000000ffffffff]
Normal [mem 0x0000000100000000-0x000000027fffffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x0000000000200000-0x000000000effffff]
node 0: [mem 0x0000000090000000-0x00000000fdffffff]
node 0: [mem 0x0000000100000000-0x000000027fffffff]
Initmem setup node 0 [mem 0x0000000000200000-0x000000027fffffff]
On node 0, zone DMA32: 128 pages in unavailable ranges
On node 0, zone DMA32: 1024 pages in unavailable ranges
On node 0, zone Normal: 2048 pages in unavailable ranges
percpu: Embedded 13 pages/cpu s170800 r8192 d34000 u212992
pcpu-alloc: s170800 r8192 d34000 u212992 alloc=13*16384
pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Fallback order for Node 0: 0
Built 1 zonelists, mobility grouping on. Total pages: 519052
Policy zone: Normal
Kernel command line: console=ttyS0,115200n8 root=/dev/md0 rootwait machtype=loongson-ls3a-rs780e-1w rd_start=0x84000000 rd_size=0x1d4a2dd
Unknown kernel command line parameters "machtype=loongson-ls3a-rs780e-1w", will be passed to user space.
Dentry cache hash table entries: 1048576 (order: 9, 8388608 bytes, linear)
Inode-cache hash table entries: 524288 (order: 8, 4194304 bytes, linear)
mem auto-init: stack:off, heap alloc:on, heap free:off
Memory: 2179040K/8337408K available (11120K kernel code, 1771K rwdata, 3064K rodata, 2704K init, 548K bss, 161872K reserved, 0K cma-reserved)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
ftrace: allocating 32056 entries in 32 pages
ftrace: allocated 32 pages with 1 groups
trace event string verifier disabled
rcu: Preemptible hierarchical RCU implementation.
rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4.
Trampoline variant of Tasks RCU enabled.
Rude variant of Tasks RCU enabled.
Tracing variant of Tasks RCU enabled.
rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
NR_IRQS: 320
ISA Bridge: /bus@10000000/isa@18000000
IO 0x0000000018000000..0x0000000018003fff -> 0x0000000000000000
rcu: srcu_init: Setting srcu_struct sizes based on contention.
clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4247245437 ns
sched_clock: 32 bits at 450MHz, resolution 2ns, wraps every 4772186110ns
Console: colour dummy device 80x25
Calibrating delay loop... 718.84 BogoMIPS (lpj=1437696)
pid_max: default: 32768 minimum: 301
LSM: Security Framework initializing
landlock: Up and running.
Yama: disabled by default; enable with sysctl kernel.yama.*
AppArmor: AppArmor initialized
TOMOYO Linux initialized
LSM support for eBPF active
Mount-cache hash table entries: 16384 (order: 3, 131072 bytes, linear)
Mountpoint-cache hash table entries: 16384 (order: 3, 131072 bytes, linear)
cblist_init_generic: Setting adjustable number of callback queues.
cblist_init_generic: Setting shift to 2 and lim to 1.
cblist_init_generic: Setting shift to 2 and lim to 1.
cblist_init_generic: Setting shift to 2 and lim to 1.
Performance counters: No available PMU.
rcu: Hierarchical SRCU implementation.
rcu: Max phase no-delay instances is 1000.
smp: Bringing up secondary CPUs ...
Booting CPU#1...
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 64kB, 4-way, VIPT, no aliases, linesize 32 bytes
Unified victim cache 0kB direct mapped, linesize 0 bytes.
Unified secondary cache 4096kB 4-way, linesize 32 bytes.
CPU1 revision is: 00006305 (ICT Loongson-3)
FPU revision is: 00770501
CPU#1 finished, CP0_ST=d400cce1
Booting CPU#2...
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 64kB, 4-way, VIPT, no aliases, linesize 32 bytes
Unified victim cache 0kB direct mapped, linesize 0 bytes.
Unified secondary cache 4096kB 4-way, linesize 32 bytes.
CPU2 revision is: 00006305 (ICT Loongson-3)
FPU revision is: 00770501
CPU#2 finished, CP0_ST=d400cce1
Booting CPU#3...
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 64kB, 4-way, VIPT, no aliases, linesize 32 bytes
Unified victim cache 0kB direct mapped, linesize 0 bytes.
Unified secondary cache 4096kB 4-way, linesize 32 bytes.
CPU3 revision is: 00006305 (ICT Loongson-3)
FPU revision is: 00770501
CPU#3 finished, CP0_ST=d400cce1
smp: Brought up 1 node, 4 CPUs
node 0 deferred pages initialised in 116ms
devtmpfs: initialized
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
futex hash table entries: 1024 (order: 2, 65536 bytes, linear)
NET: Registered PF_NETLINK/PF_ROUTE protocol family
audit: initializing netlink subsys (disabled)
audit: type=2000 audit(0.484:1): state=initialized audit_enabled=0 res=1
thermal_sys: Registered thermal governor 'fair_share'
thermal_sys: Registered thermal governor 'bang_bang'
thermal_sys: Registered thermal governor 'step_wise'
thermal_sys: Registered thermal governor 'user_space'
cpuidle: using governor ladder
cpuidle: using governor menu
HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages
HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page
iommu: Default domain type: Translated
iommu: DMA domain TLB invalidation policy: strict mode
SCSI subsystem initialized
libata version 3.00 loaded.
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
NetLabel: unlabeled traffic allowed by default
vgaarb: loaded
clocksource: Switched to clocksource MIPS
VFS: Disk quotas dquot_6.6.0
VFS: Dquot-cache hash table entries: 2048 (order 0, 16384 bytes)
AppArmor: AppArmor Filesystem Enabled
NET: Registered PF_INET protocol family
IP idents hash table entries: 131072 (order: 6, 1048576 bytes, linear)
tcp_listen_portaddr_hash hash table entries: 4096 (order: 2, 65536 bytes, linear)
Table-perturb hash table entries: 65536 (order: 4, 262144 bytes, linear)
TCP established hash table entries: 65536 (order: 5, 524288 bytes, linear)
TCP bind hash table entries: 65536 (order: 7, 2097152 bytes, linear)
TCP: Hash tables configured (established 65536 bind 65536)
MPTCP token hash table entries: 8192 (order: 3, 196608 bytes, linear)
UDP hash table entries: 4096 (order: 3, 131072 bytes, linear)
UDP-Lite hash table entries: 4096 (order: 3, 131072 bytes, linear)
NET: Registered PF_UNIX/PF_LOCAL protocol family
NET: Registered PF_XDP protocol family
PCI: CLS 0 bytes, default 32
Trying to unpack rootfs image as initramfs...
Initialise system trusted keyrings
Key type blacklist registered
workingset: timestamp_bits=40 max_order=19 bucket_order=0
zbud: loaded
integrity: Platform Keyring initialized
Key type asymmetric registered
Asymmetric key parser 'x509' registered
Freeing initrd memory: 29984K
process '/usr/bin/kmod' started with executable stack
alg: self-tests for CTR-KDF (hmac(sha256)) passed
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
io scheduler mq-deadline registered
loongson-pci 1a000000.pci: host bridge /bus@10000000/pci@1a000000 ranges:
loongson-pci 1a000000.pci: No bus range found for /bus@10000000/pci@1a000000, using [bus 00-ff]
loongson-pci 1a000000.pci: IO 0x0018004000..0x001800ffff -> 0x0000004000
loongson-pci 1a000000.pci: MEM 0x0040000000..0x007fffffff -> 0x0040000000
loongson-pci 1a000000.pci: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [io 0x4000-0xffff]
pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
pci 0000:00:00.0: [1022:9600] type 00 class 0x060000
pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x4 may corrupt adjacent RW1C bits
pci 0000:00:01.0: [1022:9602] type 01 class 0x060400
pci 0000:00:02.0: [1022:9603] type 01 class 0x060400
pci 0000:00:02.0: enabling Extended Tags
pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
pci 0000:00:03.0: [1022:960b] type 01 class 0x060400
pci 0000:00:03.0: enabling Extended Tags
pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
pci 0000:00:04.0: [1022:9604] type 01 class 0x060400
pci 0000:00:04.0: enabling Extended Tags
pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
pci 0000:00:05.0: [1022:9605] type 01 class 0x060400
pci 0000:00:05.0: enabling Extended Tags
pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
pci 0000:00:06.0: [1022:9606] type 01 class 0x060400
pci 0000:00:06.0: enabling Extended Tags
pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
pci 0000:00:07.0: [1022:9607] type 01 class 0x060400
pci 0000:00:07.0: enabling Extended Tags
pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
pci 0000:00:09.0: [1022:9608] type 01 class 0x060400
pci 0000:00:09.0: enabling Extended Tags
pci 0000:00:09.0: PME# supported from D0 D3hot D3cold
pci 0000:00:0a.0: [1022:9609] type 01 class 0x060400
pci 0000:00:0a.0: enabling Extended Tags
pci 0000:00:0a.0: PME# supported from D0 D3hot D3cold
pci 0000:00:11.0: [1002:4390] type 00 class 0x010601
pci 0000:00:11.0: reg 0x10: [io 0xe058-0xe05f]
pci 0000:00:11.0: reg 0x14: [io 0xe050-0xe053]
pci 0000:00:11.0: reg 0x18: [io 0xe048-0xe04f]
pci 0000:00:11.0: reg 0x1c: [io 0xe040-0xe043]
pci 0000:00:11.0: reg 0x20: [io 0xe010-0xe01f]
pci 0000:00:11.0: reg 0x24: [mem 0x48a09000-0x48a093ff]
pci 0000:00:12.0: [1002:4397] type 00 class 0x0c0310
pci 0000:00:12.0: reg 0x10: [mem 0x48a08000-0x48a08fff]
pci 0000:00:12.1: [1002:4398] type 00 class 0x0c0310
pci 0000:00:12.1: reg 0x10: [mem 0x48a07000-0x48a07fff]
pci 0000:00:12.2: [1002:4396] type 00 class 0x0c0320
pci 0000:00:12.2: reg 0x10: [mem 0x00000000-0x000000ff]
pci 0000:00:12.2: supports D1 D2
pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:13.0: [1002:4397] type 00 class 0x0c0310
pci 0000:00:13.0: reg 0x10: [mem 0x48a06000-0x48a06fff]
pci 0000:00:13.1: [1002:4398] type 00 class 0x0c0310
pci 0000:00:13.1: reg 0x10: [mem 0x48a05000-0x48a05fff]
pci 0000:00:13.2: [1002:4396] type 00 class 0x0c0320
pci 0000:00:13.2: reg 0x10: [mem 0x00000000-0x000000ff]
pci 0000:00:13.2: supports D1 D2
pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500
pci 0000:00:14.1: [1002:439c] type 00 class 0x01018a
pci 0000:00:14.1: reg 0x10: [io 0xe038-0xe03f]
pci 0000:00:14.1: reg 0x14: [io 0xe030-0xe033]
pci 0000:00:14.1: reg 0x18: [io 0xe028-0xe02f]
pci 0000:00:14.1: reg 0x1c: [io 0xe020-0xe023]
pci 0000:00:14.1: reg 0x20: [io 0xe000-0xe00f]
pci 0000:00:14.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
pci 0000:00:14.1: legacy IDE quirk: reg 0x14: [io 0x03f6]
pci 0000:00:14.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
pci 0000:00:14.1: legacy IDE quirk: reg 0x1c: [io 0x0376]
pci 0000:00:14.2: [1002:4383] type 00 class 0x040300
pci 0000:00:14.2: reg 0x10: [mem 0x48a00000-0x48a03fff 64bit]
pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
pci 0000:00:14.3: [1002:439d] type 00 class 0x060100
pci 0000:00:14.4: [1002:4384] type 01 class 0x060401
pci 0000:00:14.5: [1002:4399] type 00 class 0x0c0310
pci 0000:00:14.5: reg 0x10: [mem 0x48a04000-0x48a04fff]
pci_bus 0000:01: extended config space not accessible
pci 0000:01:05.0: [1002:9615] type 00 class 0x030000
pci_bus 0000:01: 2-byte config write to 0000:01:05.0 offset 0x4 may corrupt adjacent RW1C bits
pci 0000:01:05.0: reg 0x10: [mem 0x40000000-0x47ffffff pref]
pci 0000:01:05.0: reg 0x14: [io 0xd000-0xd0ff]
pci 0000:01:05.0: reg 0x18: [mem 0x48000000-0x4800ffff]
pci 0000:01:05.0: Video device with shadowed ROM at [mem 0x0f127950-0x0f16794f]
pci 0000:01:05.0: supports D1 D2
pci 0000:01:05.0: vgaarb: setting as boot VGA device
pci 0000:01:05.0: vgaarb: bridge control possible
pci 0000:01:05.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
pci 0000:00:01.0: PCI bridge to [bus 01-ff]
pci 0000:00:01.0: bridge window [io 0xd000-0xdfff]
pci 0000:00:01.0: bridge window [mem 0x40000000-0x480fffff]
pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
pci 0000:00:02.0: PCI bridge to [bus 02-ff]
pci 0000:00:02.0: bridge window [io 0xc000-0xcfff]
pci 0000:00:02.0: bridge window [mem 0x48900000-0x489fffff]
pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
pci 0000:00:03.0: PCI bridge to [bus 03-ff]
pci 0000:00:03.0: bridge window [io 0xb000-0xbfff]
pci 0000:00:03.0: bridge window [mem 0x48800000-0x488fffff]
pci_bus 0000:03: busn_res: [bus 03-ff] end is updated to 03
pci 0000:00:04.0: PCI bridge to [bus 04-ff]
pci 0000:00:04.0: bridge window [io 0xa000-0xafff]
pci 0000:00:04.0: bridge window [mem 0x48700000-0x487fffff]
pci_bus 0000:04: busn_res: [bus 04-ff] end is updated to 04
pci 0000:00:05.0: PCI bridge to [bus 05-ff]
pci 0000:00:05.0: bridge window [io 0x9000-0x9fff]
pci 0000:00:05.0: bridge window [mem 0x48600000-0x486fffff]
pci_bus 0000:05: busn_res: [bus 05-ff] end is updated to 05
pci 0000:00:06.0: PCI bridge to [bus 06-ff]
pci 0000:00:06.0: bridge window [io 0x8000-0x8fff]
pci 0000:00:06.0: bridge window [mem 0x48500000-0x485fffff]
pci_bus 0000:06: busn_res: [bus 06-ff] end is updated to 06
pci 0000:07:00.0: [10ec:8168] type 00 class 0x020000
pci_bus 0000:07: 2-byte config write to 0000:07:00.0 offset 0x4 may corrupt adjacent RW1C bits
pci 0000:07:00.0: reg 0x10: [io 0x7000-0x70ff]
pci 0000:07:00.0: reg 0x18: [mem 0x48414000-0x48414fff 64bit pref]
pci 0000:07:00.0: reg 0x20: [mem 0x48410000-0x48413fff 64bit pref]
pci 0000:07:00.0: reg 0x30: [mem 0x48400000-0x4840ffff pref]
pci 0000:07:00.0: supports D1 D2
pci 0000:07:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:07.0: PCI bridge to [bus 07-ff]
pci 0000:00:07.0: bridge window [io 0x7000-0x7fff]
pci 0000:00:07.0: bridge window [mem 0x48400000-0x484fffff]
pci_bus 0000:07: busn_res: [bus 07-ff] end is updated to 07
pci 0000:00:09.0: PCI bridge to [bus 08-ff]
pci 0000:00:09.0: bridge window [io 0x6000-0x6fff]
pci 0000:00:09.0: bridge window [mem 0x48300000-0x483fffff]
pci_bus 0000:08: busn_res: [bus 08-ff] end is updated to 08
pci 0000:00:0a.0: PCI bridge to [bus 09-ff]
pci 0000:00:0a.0: bridge window [io 0x5000-0x5fff]
pci 0000:00:0a.0: bridge window [mem 0x48200000-0x482fffff]
pci_bus 0000:09: busn_res: [bus 09-ff] end is updated to 09
pci_bus 0000:0a: extended config space not accessible
pci 0000:00:14.4: PCI bridge to [bus 0a-ff] (subtractive decode)
pci 0000:00:14.4: bridge window [io 0x4000-0x4fff]
pci 0000:00:14.4: bridge window [mem 0x48100000-0x481fffff]
pci 0000:00:14.4: bridge window [io 0x4000-0xffff] (subtractive decode)
pci 0000:00:14.4: bridge window [mem 0x40000000-0x7fffffff] (subtractive decode)
pci_bus 0000:0a: busn_res: [bus 0a-ff] end is updated to 0a
pci 0000:00:01.0: BAR 14: assigned [mem 0x40000000-0x4bffffff]
pci 0000:00:02.0: BAR 14: assigned [mem 0x4c000000-0x4c0fffff]
pci 0000:00:03.0: BAR 14: assigned [mem 0x4c100000-0x4c1fffff]
pci 0000:00:04.0: BAR 14: assigned [mem 0x4c200000-0x4c2fffff]
pci 0000:00:05.0: BAR 14: assigned [mem 0x4c300000-0x4c3fffff]
pci 0000:00:06.0: BAR 14: assigned [mem 0x4c400000-0x4c4fffff]
pci 0000:00:07.0: BAR 14: assigned [mem 0x4c500000-0x4c5fffff]
pci 0000:00:07.0: BAR 15: assigned [mem 0x4c600000-0x4c6fffff 64bit pref]
pci 0000:00:09.0: BAR 14: assigned [mem 0x4c700000-0x4c7fffff]
pci 0000:00:0a.0: BAR 14: assigned [mem 0x4c800000-0x4c8fffff]
pci 0000:00:14.4: BAR 14: assigned [mem 0x4c900000-0x4c9fffff]
pci 0000:00:14.2: BAR 0: assigned [mem 0x4ca00000-0x4ca03fff 64bit]
pci 0000:00:01.0: BAR 13: assigned [io 0x4000-0x4fff]
pci 0000:00:02.0: BAR 13: assigned [io 0x5000-0x5fff]
pci 0000:00:03.0: BAR 13: assigned [io 0x6000-0x6fff]
pci 0000:00:04.0: BAR 13: assigned [io 0x7000-0x7fff]
pci 0000:00:05.0: BAR 13: assigned [io 0x8000-0x8fff]
pci 0000:00:06.0: BAR 13: assigned [io 0x9000-0x9fff]
pci 0000:00:07.0: BAR 13: assigned [io 0xa000-0xafff]
pci 0000:00:09.0: BAR 13: assigned [io 0xb000-0xbfff]
pci 0000:00:0a.0: BAR 13: assigned [io 0xc000-0xcfff]
pci 0000:00:12.0: BAR 0: assigned [mem 0x4ca04000-0x4ca04fff]
pci 0000:00:12.1: BAR 0: assigned [mem 0x4ca05000-0x4ca05fff]
pci 0000:00:13.0: BAR 0: assigned [mem 0x4ca06000-0x4ca06fff]
pci 0000:00:13.1: BAR 0: assigned [mem 0x4ca07000-0x4ca07fff]
pci 0000:00:14.4: BAR 13: assigned [io 0xd000-0xdfff]
pci 0000:00:14.5: BAR 0: assigned [mem 0x4ca08000-0x4ca08fff]
pci 0000:00:11.0: BAR 5: assigned [mem 0x4ca09000-0x4ca093ff]
pci 0000:00:12.2: BAR 0: assigned [mem 0x4ca09400-0x4ca094ff]
pci 0000:00:13.2: BAR 0: assigned [mem 0x4ca09500-0x4ca095ff]
pci 0000:00:11.0: BAR 4: assigned [io 0xe000-0xe00f]
pci 0000:00:14.1: BAR 4: assigned [io 0xe010-0xe01f]
pci 0000:00:11.0: BAR 0: assigned [io 0xe020-0xe027]
pci 0000:00:11.0: BAR 2: assigned [io 0xe028-0xe02f]
pci 0000:00:11.0: BAR 1: assigned [io 0xe030-0xe033]
pci 0000:00:11.0: BAR 3: assigned [io 0xe034-0xe037]
pci 0000:01:05.0: BAR 0: assigned [mem 0x40000000-0x47ffffff pref]
pci 0000:01:05.0: BAR 2: assigned [mem 0x48000000-0x4800ffff]
pci 0000:01:05.0: BAR 1: assigned [io 0x4000-0x40ff]
pci 0000:00:01.0: PCI bridge to [bus 01]
pci 0000:00:01.0: bridge window [io 0x4000-0x4fff]
pci 0000:00:01.0: bridge window [mem 0x40000000-0x4bffffff]
pci 0000:00:02.0: PCI bridge to [bus 02]
pci 0000:00:02.0: bridge window [io 0x5000-0x5fff]
pci 0000:00:02.0: bridge window [mem 0x4c000000-0x4c0fffff]
pci 0000:00:03.0: PCI bridge to [bus 03]
pci 0000:00:03.0: bridge window [io 0x6000-0x6fff]
pci 0000:00:03.0: bridge window [mem 0x4c100000-0x4c1fffff]
pci 0000:00:04.0: PCI bridge to [bus 04]
pci 0000:00:04.0: bridge window [io 0x7000-0x7fff]
pci 0000:00:04.0: bridge window [mem 0x4c200000-0x4c2fffff]
pci 0000:00:05.0: PCI bridge to [bus 05]
pci 0000:00:05.0: bridge window [io 0x8000-0x8fff]
pci 0000:00:05.0: bridge window [mem 0x4c300000-0x4c3fffff]
pci 0000:00:06.0: PCI bridge to [bus 06]
pci 0000:00:06.0: bridge window [io 0x9000-0x9fff]
pci 0000:00:06.0: bridge window [mem 0x4c400000-0x4c4fffff]
pci 0000:07:00.0: BAR 6: assigned [mem 0x4c500000-0x4c50ffff pref]
pci 0000:07:00.0: BAR 4: assigned [mem 0x4c600000-0x4c603fff 64bit pref]
pci 0000:07:00.0: BAR 2: assigned [mem 0x4c604000-0x4c604fff 64bit pref]
pci 0000:07:00.0: BAR 0: assigned [io 0xa000-0xa0ff]
pci 0000:00:07.0: PCI bridge to [bus 07]
pci 0000:00:07.0: bridge window [io 0xa000-0xafff]
pci 0000:00:07.0: bridge window [mem 0x4c500000-0x4c5fffff]
pci 0000:00:07.0: bridge window [mem 0x4c600000-0x4c6fffff 64bit pref]
pci 0000:00:09.0: PCI bridge to [bus 08]
pci 0000:00:09.0: bridge window [io 0xb000-0xbfff]
pci 0000:00:09.0: bridge window [mem 0x4c700000-0x4c7fffff]
pci 0000:00:0a.0: PCI bridge to [bus 09]
pci 0000:00:0a.0: bridge window [io 0xc000-0xcfff]
pci 0000:00:0a.0: bridge window [mem 0x4c800000-0x4c8fffff]
pci 0000:00:14.4: PCI bridge to [bus 0a]
pci 0000:00:14.4: bridge window [io 0xd000-0xdfff]
pci 0000:00:14.4: bridge window [mem 0x4c900000-0x4c9fffff]
pci 0000:00:01.0: MSI quirk detected; subordinate MSI disabled
pcieport 0000:00:02.0: of_irq_parse_pci: failed with rc=-22
pcieport 0000:00:03.0: of_irq_parse_pci: failed with rc=-22
pci 0000:00:12.0: enabling device (0140 -> 0142)
pci 0000:00:12.1: enabling device (0140 -> 0142)
pci 0000:00:12.2: enabling device (0000 -> 0002)
pci 0000:00:13.0: enabling device (0140 -> 0142)
pci 0000:00:13.1: enabling device (0140 -> 0142)
pci 0000:00:13.2: enabling device (0000 -> 0002)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
printk: console [ttyS0] disabled
1fe001e0.serial: ttyS0 at MMIO 0x1fe001e0 (irq = 28, base_baud = 2062500) is a 16550A
printk: console [ttyS0] enabled
printk: bootconsole [early0] disabled
ahci 0000:00:11.0: of_irq_parse_pci: failed with rc=-22
ahci 0000:00:11.0: version 3.0
ahci 0000:00:11.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc
scsi host0: ahci
scsi host1: ahci
scsi host2: ahci
scsi host3: ahci
ata1: SATA max UDMA/133 abar m1024@0x4ca09000 port 0x4ca09100 irq 4
ata2: SATA max UDMA/133 abar m1024@0x4ca09000 port 0x4ca09180 irq 4
ata3: SATA max UDMA/133 abar m1024@0x4ca09000 port 0x4ca09200 irq 4
ata4: SATA max UDMA/133 abar m1024@0x4ca09000 port 0x4ca09280 irq 4
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mousedev: PS/2 mouse device common for all mice
rtc_cmos 18000070.rtc: registered as rtc0
rtc_cmos 18000070.rtc: setting system clock to 2023-07-15T20:15:00 UTC (1689452100)
rtc_cmos 18000070.rtc: alarms up to one day, 242 bytes nvram
ledtrig-cpu: registered to indicate activity on CPUs
atkbd serio0: keyboard reset failed on isa0060/serio0
Loongson Hwmon Enter...
NET: Registered PF_INET6 protocol family
Segment Routing with IPv6
In-situ OAM (IOAM) with IPv6
mip6: Mobile IPv6
NET: Registered PF_PACKET protocol family
mpls_gso: MPLS GSO support
atkbd serio1: keyboard reset failed on isa0060/serio1
registered taskstats version 1
Loading compiled-in X.509 certificates
ata4: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-8: WDC WD5000AAKX-60U6AA0, 18.01H18, max UDMA/100
ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32), AA
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA WDC WD5000AAKX-6 1H18 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
sd 0:0:0:0: [sda] Write Protect is off
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes
ata2.00: ATA-8: ST500DM002-1BD142, KC48, max UDMA/133
ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 32)
sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA ST500DM002-1BD14 KC48 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/466 GiB)
sd 1:0:0:0: [sdb] 4096-byte physical blocks
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes
Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1'
Loaded X.509 cert 'Debian Secure Boot Signer 2022 - linux: 14011249c2675ea8e5148542202005810584b25f'
sdb: sdb1 sdb2 sdb3
Problem parsing in-kernel X.509 certificate list
sd 1:0:0:0: [sdb] Attached SCSI disk
zswap: loaded using pool lzo/zbud
Key type .fscrypt registered
Key type fscrypt-provisioning registered
Key type encrypted registered
AppArmor: AppArmor sha1 policy hashing enabled
ima: No TPM chip found, activating TPM-bypass!
ima: Allocated hash algorithm: sha256
ima: No architecture policies found
evm: Initialising EVM extended attributes:
evm: security.selinux
evm: security.SMACK64 (disabled)
evm: security.SMACK64EXEC (disabled)
evm: security.SMACK64TRANSMUTE (disabled)
evm: security.SMACK64MMAP (disabled)
evm: security.apparmor
evm: security.ima
evm: security.capability
evm: HMAC attrs: 0x1
Freeing unused kernel image (initmem) memory: 2704K
This architecture does not have kernel memory protection.
Run /init as init process
with arguments:
/init
with environment:
HOME=/
TERM=linux
machtype=loongson-ls3a-rs780e-1w
usbcore: registered new interface driver usbfs
pci 0000:00:07.0: of_irq_parse_pci: failed with rc=-22
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ata_generic 0000:00:14.1: of_irq_parse_pci: failed with rc=-22
ehci-pci 0000:00:12.2: of_irq_parse_pci: failed with rc=-22
ehci-pci 0000:00:12.2: EHCI Host Controller
ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 1
ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
ehci-pci 0000:00:12.2: debug port 1
r8169 0000:07:00.0 eth0: RTL8168d/8111d, 00:23:a0:00:02:df, XID 281, IRQ 5
r8169 0000:07:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko]
ehci-pci 0000:00:12.2: irq 6, io mem 0x4ca09400
ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 6.1.0-0.deb11.5-loongson-3 ehci_hcd
usb usb1: SerialNumber: 0000:00:12.2
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ehci-pci 0000:00:13.2: of_irq_parse_pci: failed with rc=-22
ehci-pci 0000:00:13.2: EHCI Host Controller
ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 2
ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
ehci-pci 0000:00:13.2: debug port 1
ehci-pci 0000:00:13.2: irq 6, io mem 0x4ca09500
ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 6.1.0-0.deb11.5-loongson-3 ehci_hcd
usb usb2: SerialNumber: 0000:00:13.2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
ohci-pci 0000:00:12.0: of_irq_parse_pci: failed with rc=-22
ohci-pci 0000:00:12.0: OHCI PCI host controller
ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 3
ohci-pci 0000:00:12.0: irq 6, io mem 0x4ca04000
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: OHCI PCI host controller
usb usb3: Manufacturer: Linux 6.1.0-0.deb11.5-loongson-3 ohci_hcd
usb usb3: SerialNumber: 0000:00:12.0
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
ohci-pci 0000:00:12.1: of_irq_parse_pci: failed with rc=-22
ohci-pci 0000:00:12.1: OHCI PCI host controller
ohci-pci 0000:00:12.1: new USB bus registered, assigned bus number 4
ohci-pci 0000:00:12.1: irq 6, io mem 0x4ca05000
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: OHCI PCI host controller
usb usb4: Manufacturer: Linux 6.1.0-0.deb11.5-loongson-3 ohci_hcd
usb usb4: SerialNumber: 0000:00:12.1
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 3 ports detected
ohci-pci 0000:00:13.0: of_irq_parse_pci: failed with rc=-22
ohci-pci 0000:00:13.0: OHCI PCI host controller
ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 5
ohci-pci 0000:00:13.0: irq 6, io mem 0x4ca06000
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: OHCI PCI host controller
usb usb5: Manufacturer: Linux 6.1.0-0.deb11.5-loongson-3 ohci_hcd
usb usb5: SerialNumber: 0000:00:13.0
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 3 ports detected
ohci-pci 0000:00:13.1: of_irq_parse_pci: failed with rc=-22
ohci-pci 0000:00:13.1: OHCI PCI host controller
random: crng init done
ohci-pci 0000:00:13.1: new USB bus registered, assigned bus number 6
ohci-pci 0000:00:13.1: irq 6, io mem 0x4ca07000
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: OHCI PCI host controller
usb usb6: Manufacturer: Linux 6.1.0-0.deb11.5-loongson-3 ohci_hcd
usb usb6: SerialNumber: 0000:00:13.1
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 3 ports detected
ohci-pci 0000:00:14.5: of_irq_parse_pci: failed with rc=-22
ohci-pci 0000:00:14.5: OHCI PCI host controller
ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 7
ohci-pci 0000:00:14.5: irq 6, io mem 0x4ca08000
usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01
usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: OHCI PCI host controller
usb usb7: Manufacturer: Linux 6.1.0-0.deb11.5-loongson-3 ohci_hcd
usb usb7: SerialNumber: 0000:00:14.5
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
md/raid1:md0: active with 2 out of 2 mirrors
md/raid1:md2: active with 2 out of 2 mirrors
md0: detected capacity change from 0 to 48795648
md/raid1:md1: active with 2 out of 2 mirrors
md1: detected capacity change from 0 to 974720
md2: detected capacity change from 0 to 926703616
raid6: int64x8 gen() 338 MB/s
raid6: int64x4 gen() 615 MB/s
raid6: int64x2 gen() 505 MB/s
raid6: int64x1 gen() 333 MB/s
raid6: using algorithm int64x4 gen() 615 MB/s
raid6: .... xor() 298 MB/s, rmw enabled
raid6: using intx1 recovery algorithm
xor: measuring software checksum speed
8regs : 1994 MB/sec
8regs_prefetch : 1540 MB/sec
32regs : 1994 MB/sec
32regs_prefetch : 1540 MB/sec
xor: using function: 32regs (1994 MB/sec)
device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log.
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com
PM: Image not found (code -22)
EXT4-fs (md0): mounted filesystem with ordered data mode. Quota mode: none.
Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist.
EXT4-fs (md0): re-mounted. Quota mode: none.
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
snd_hda_intel 0000:00:14.2: of_irq_parse_pci: failed with rc=-22
snd_hda_intel 0000:00:14.2: Force to snoop mode by module option
[drm] radeon kernel modesetting enabled.
pci 0000:00:01.0: of_irq_parse_pci: failed with rc=-22
[drm] initializing kernel modesetting (RS780 0x1002:0x9615 0x1002:0x0000 0x00).
ATOM BIOS: 113
radeon 0000:01:05.0: VRAM: 128M 0x0000000040000000 - 0x0000000047FFFFFF (128M used)
radeon 0000:01:05.0: GTT: 512M 0x0000000048000000 - 0x0000000067FFFFFF
[drm:rs690_pm_info [radeon]] *ERROR* No integrated system info for your GPU, using safe default
[drm:radeon_atombios_sideport_present [radeon]] *ERROR* Unsupported IGP table: 1 4
[drm] Detected VRAM RAM=128M, BAR=128M
[drm] RAM width 32bits DDR
[drm] radeon: 128M of VRAM memory ready
[drm] radeon: 512M of GTT memory ready.
[drm] Loading RS780 Microcode
radeon 0000:01:05.0: firmware: direct-loading firmware radeon/RS780_pfp.bin
radeon 0000:01:05.0: firmware: direct-loading firmware radeon/RS780_me.bin
radeon 0000:01:05.0: firmware: direct-loading firmware radeon/R600_rlc.bin
radeon 0000:01:05.0: firmware: direct-loading firmware radeon/RS780_uvd.bin
[drm] GART: num cpu pages 32768, num gpu pages 131072
[drm] PCIE GART of 512M enabled (table at 0x0000000040148000).
radeon 0000:01:05.0: WB enabled
radeon 0000:01:05.0: fence driver on ring 0 use gpu addr 0x0000000048000c00
radeon 0000:01:05.0: fence driver on ring 5 use gpu addr 0x0000000040056038
radeon 0000:01:05.0: radeon: MSI limited to 32-bit
[drm] radeon: irq initialized.
[drm] ring test on 0 succeeded in 0 usecs
[drm] ring test on 5 succeeded in 1 usecs
[drm] UVD initialized successfully.
[drm] ib test on ring 0 succeeded in 0 usecs
snd_hda_intel 0000:00:14.2: azx_get_response timeout, switching to polling mode: last cmd=0x000f0000
[drm] ib test on ring 5 succeeded
[drm] Radeon Display Connectors
[drm] Connector 0:
[drm] VGA-1
[drm] DDC: 0x7e40 0x7e40 0x7e44 0x7e44 0x7e48 0x7e48 0x7e4c 0x7e4c
[drm] Encoders:
[drm] CRT1: INTERNAL_KLDSCP_DAC1
[drm] Connector 1:
[drm] DVI-D-1
[drm] HPD3
[drm] DDC: 0x7e60 0x7e60 0x7e64 0x7e64 0x7e68 0x7e68 0x7e6c 0x7e6c
[drm] Encoders:
[drm] DFP3: INTERNAL_KLDSCP_LVTMA
radeon 0000:01:05.0: [drm] Cannot find any crtc or sizes
[drm] Initialized radeon 2.50.0 20080528 for 0000:01:05.0 on minor 0
snd_hda_codec_realtek hdaudioC0D0: ALC888: SKU not ready 0x00000100
snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC888: line_outs=4 (0x14/0x16/0x15/0x17/0x0) type:line
snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
snd_hda_codec_realtek hdaudioC0D0: dig-out=0x1e/0x0
snd_hda_codec_realtek hdaudioC0D0: inputs:
snd_hda_codec_realtek hdaudioC0D0: Rear Mic=0x18
snd_hda_codec_realtek hdaudioC0D0: Front Mic=0x19
snd_hda_codec_realtek hdaudioC0D0: Line=0x1a
snd_hda_codec_realtek hdaudioC0D0: CD=0x1c
input: HDA Digital PCBeep as /devices/platform/bus@10000000/1a000000.pci/pci0000:00/0000:00:14.2/sound/card0/input3
input: HDA ATI SB Rear Mic as /devices/platform/bus@10000000/1a000000.pci/pci0000:00/0000:00:14.2/sound/card0/input4
input: HDA ATI SB Front Mic as /devices/platform/bus@10000000/1a000000.pci/pci0000:00/0000:00:14.2/sound/card0/input5
input: HDA ATI SB Line as /devices/platform/bus@10000000/1a000000.pci/pci0000:00/0000:00:14.2/sound/card0/input6
input: HDA ATI SB Line Out Front as /devices/platform/bus@10000000/1a000000.pci/pci0000:00/0000:00:14.2/sound/card0/input7
input: HDA ATI SB Line Out Surround as /devices/platform/bus@10000000/1a000000.pci/pci0000:00/0000:00:14.2/sound/card0/input8
input: HDA ATI SB Line Out CLFE as /devices/platform/bus@10000000/1a000000.pci/pci0000:00/0000:00:14.2/sound/card0/input9
input: HDA ATI SB Line Out Side as /devices/platform/bus@10000000/1a000000.pci/pci0000:00/0000:00:14.2/sound/card0/input10
input: HDA ATI SB Front Headphone as /devices/platform/bus@10000000/1a000000.pci/pci0000:00/0000:00:14.2/sound/card0/input11
input: HDA ATI SB SPDIF as /devices/platform/bus@10000000/1a000000.pci/pci0000:00/0000:00:14.2/sound/card0/input12
Adding 104857584k swap on /dev/mapper/vg0-swap. Priority:-2 extents:1 across:104857584k FS
[drm] amdgpu kernel modesetting enabled.
radeon 0000:01:05.0: [drm] Cannot find any crtc or sizes
EXT4-fs (md1): mounting ext3 file system using the ext4 subsystem
EXT4-fs (md1): mounted filesystem with ordered data mode. Quota mode: none.
ext3 filesystem being mounted at /boot supports timestamps until 2038 (0x7fffffff)
EXT4-fs (dm-1): mounted filesystem with ordered data mode. Quota mode: none.
r8169 0000:07:00.0: firmware: direct-loading firmware rtl_nic/rtl8168d-1.fw
RTL8211B Gigabit Ethernet r8169-0-700:00: attached PHY driver (mii_bus:phy_addr=r8169-0-700:00, irq=MAC)
r8169 0000:07:00.0 eth0: No native access to PCI extended config space, falling back to CSI
r8169 0000:07:00.0 eth0: Link is Down
RTL8211B Gigabit Ethernet r8169-0-700:00: attached PHY driver (mii_bus:phy_addr=r8169-0-700:00, irq=MAC)
r8169 0000:07:00.0 eth0: Link is Down
RTL8211B Gigabit Ethernet r8169-0-700:00: attached PHY driver (mii_bus:phy_addr=r8169-0-700:00, irq=MAC)
r8169 0000:07:00.0 eth0: Link is Down
Attachment:
signature.asc
Description: PGP signature