Bug#809876: linux-image-3.16.0-4-686-pae: Realtek RTL8185, rtl818x
Package: src:linux
Version: 3.16.7-ckt20-1+deb8u1
Severity: normal
Dear Maintainer,
*** Reporter, please consider answering these questions, where appropriate ***
* What led up to the situation?
The System freeze after aktivate the WLAN Device RTL8185L.
* What exactly did you do (or not do) that was effective (or
ineffective)?
#:ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 00:30:05:4c:fe:bd brd ff:ff:ff:ff:ff:ff
inet 192.168.20.100/24 brd 192.168.20.255 scope global eth0
valid_lft forever preferred_lft forever
inet6 fe80::230:5ff:fe4c:febd/64 scope link
valid_lft forever preferred_lft forever
3: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 00:17:3f:2e:88:0a brd ff:ff:ff:ff:ff:ff
#:iwconfig
wlan0 IEEE 802.11bg ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:on
lo no wireless extensions.
eth0 no wireless extensions.
and after #:ip link set wlan0 up -> system freeze
* What was the outcome of this action?
after pof and pon the system running.
* What outcome did you expect instead?
-- Package-specific info:
** Version:
Linux version 3.16.0-4-686-pae (debian-kernel@lists.debian.org) (gcc version 4.8.4 (Debian 4.8.4-1) ) #1 SMP Debian 3.16.7-ckt20-1+deb8u1 (2015-12-14)
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.16.0-4-686-pae root=UUID=fd1c5394-eeeb-4a44-9fc7-1badd84679cb ro
** Not tainted
** Kernel log:
[ 8.922222] systemd[1]: Reached target Remote File Systems (Pre).
[ 8.922351] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ 8.922899] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 8.923011] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 8.923159] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 8.923251] systemd[1]: Expecting device dev-disk-by\x2duuid-80b7bd0a\x2d687f\x2d4ae3\x2d9111\x2d6eaa3dc6e6d6.device...
[ 8.923548] systemd[1]: Starting Root Slice.
[ 8.923906] systemd[1]: Created slice Root Slice.
[ 8.923980] systemd[1]: Starting User and Session Slice.
[ 8.924443] systemd[1]: Created slice User and Session Slice.
[ 8.924521] systemd[1]: Starting Delayed Shutdown Socket.
[ 8.924914] systemd[1]: Listening on Delayed Shutdown Socket.
[ 8.924989] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 8.925374] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 8.925452] systemd[1]: Starting Journal Socket (/dev/log).
[ 8.925837] systemd[1]: Listening on Journal Socket (/dev/log).
[ 8.925916] systemd[1]: Starting Device-mapper event daemon FIFOs.
[ 8.940532] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 8.940622] systemd[1]: Starting LVM2 metadata daemon socket.
[ 8.941021] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 8.941108] systemd[1]: Starting udev Control Socket.
[ 8.941471] systemd[1]: Listening on udev Control Socket.
[ 8.941551] systemd[1]: Starting udev Kernel Socket.
[ 8.941902] systemd[1]: Listening on udev Kernel Socket.
[ 8.941991] systemd[1]: Starting Journal Socket.
[ 8.942384] systemd[1]: Listening on Journal Socket.
[ 8.942506] systemd[1]: Starting System Slice.
[ 8.942935] systemd[1]: Created slice System Slice.
[ 8.943027] systemd[1]: Started File System Check on Root Device.
[ 8.943098] systemd[1]: Starting system-getty.slice.
[ 8.943548] systemd[1]: Created slice system-getty.slice.
[ 8.943624] systemd[1]: Starting system-serial\x2dgetty.slice.
[ 8.944106] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 8.944229] systemd[1]: Starting Increase datagram queue length...
[ 8.945839] systemd[1]: Starting Nameserver information manager...
[ 8.981144] systemd[1]: Started Set Up Additional Binary Formats.
[ 8.995569] systemd[1]: Starting Load Kernel Modules...
[ 8.997523] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 8.999854] systemd[1]: Mounting POSIX Message Queue File System...
[ 9.002472] systemd[1]: Mounting Debug File System...
[ 9.004750] systemd[1]: Mounting Huge Pages File System...
[ 9.007536] systemd[1]: Starting udev Coldplug all Devices...
[ 9.009923] systemd[1]: Starting Slices.
[ 9.010490] systemd[1]: Reached target Slices.
[ 9.173188] systemd[1]: Started Load Kernel Modules.
[ 9.173860] systemd[1]: Mounted FUSE Control File System.
[ 9.173957] systemd[1]: Starting Apply Kernel Variables...
[ 9.175950] systemd[1]: Mounted Configuration File System.
[ 9.213685] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ 9.214198] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 9.363864] systemd[1]: Started udev Coldplug all Devices.
[ 9.364570] systemd[1]: Starting udev Wait for Complete Device Initialization...
[ 9.412649] systemd[1]: Started Apply Kernel Variables.
[ 9.613094] systemd[1]: Started Increase datagram queue length.
[ 9.634237] systemd[1]: Starting Syslog Socket.
[ 9.634707] systemd[1]: Listening on Syslog Socket.
[ 9.634816] systemd[1]: Starting Journal Service...
[ 9.637463] systemd[1]: Started Journal Service.
[ 10.125719] systemd-udevd[169]: starting version 215
[ 11.618276] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 11.618370] ACPI: Power Button [PWRB]
[ 11.618700] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 11.618777] ACPI: Power Button [PWRF]
[ 12.011436] intel_rng: FWH not detected
[ 12.112593] parport_pc 00:04: reported by Plug and Play ACPI
[ 12.112714] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 12.207231] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 12.257663] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 12.457176] i801_smbus 0000:00:1f.3: SMBus using PCI Interrupt
[ 12.480937] ppdev: user-space parallel port driver
[ 12.700796] iTCO_vendor_support: vendor-support=0
[ 12.903322] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 12.903504] iTCO_wdt: Found a ICH5 or ICH5R TCO device (Version=1, TCOBASE=0xf060)
[ 12.903954] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 12.988656] [drm] Initialized drm 1.1.0 20060810
[ 13.101974] cfg80211: Calling CRDA to update world regulatory domain
[ 13.159253] [drm] Memory usable by graphics device = 128M
[ 13.159327] [drm] Replacing VGA console driver
[ 13.160556] Console: switching to colour dummy device 80x25
[ 13.161376] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 13.161401] [drm] Driver supports precise vblank timestamp query.
[ 13.161512] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 13.166935] [drm] initialized overlay support
[ 13.176632] i915 0000:00:02.0: No connectors reported connected with modes
[ 13.176654] [drm] Cannot find any crtc or sizes - going 1024x768
[ 13.183768] fbcon: inteldrmfb (fb0) is primary device
[ 13.201095] Console: switching to colour frame buffer device 128x48
[ 13.205908] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 13.205975] i915 0000:00:02.0: registered panic notifier
[ 13.227657] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 13.766997] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 13.767493] ieee80211 phy0: hwaddr 00173f2e880a, RTL8185vD + rtl8225z2
[ 13.888474] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 14.024050] snd_intel8x0 0000:00:1f.5: intel8x0_measure_ac97_clock: measured 55933 usecs (2695 samples)
[ 14.024160] snd_intel8x0 0000:00:1f.5: clocking to 48000
[ 14.087233] Adding 1562620k swap on /dev/sda5. Priority:-1 extents:1 across:1562620k FS
[ 14.565863] systemd-journald[159]: Received request to flush runtime journal from PID 1
[ 15.237053] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 15.240956] e100 0000:03:08.0 eth0: NIC Link is Up 100 Mbps Full Duplex
[ 15.244867] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
** Model information
not available
** Loaded modules:
binfmt_misc
arc4
rtl818x_pci
snd_intel8x0
snd_ac97_codec
eeprom_93cx6
snd_pcm
mac80211
snd_timer
snd
i915
soundcore
cfg80211
video
drm_kms_helper
drm
iTCO_wdt
ac97_bus
i2c_algo_bit
serio_raw
iTCO_vendor_support
rfkill
evdev
ppdev
i2c_i801
i2c_core
lpc_ich
mfd_core
shpchp
pcspkr
parport_pc
parport
rng_core
button
processor
thermal_sys
autofs4
ext4
crc16
mbcache
jbd2
dm_mod
sg
sr_mod
sd_mod
crc_t10dif
cdrom
crct10dif_generic
crct10dif_common
ata_generic
ata_piix
libata
scsi_mod
e100
mii
floppy
ehci_pci
uhci_hcd
ehci_hcd
usbcore
usb_common
** Network interface configuration:
# remove the above line if you edit this file
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet static
address 192.168.20.100
netmask 255.255.255.0
gateway 192.168.20.1
dns-nameservers 192.168.20.1
iface eth1 inet dhcp
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 00:30:05:4c:fe:bd brd ff:ff:ff:ff:ff:ff
inet 192.168.20.100/24 brd 192.168.20.255 scope global eth0
valid_lft forever preferred_lft forever
inet6 fe80::230:5ff:fe4c:febd/64 scope link
valid_lft forever preferred_lft forever
3: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 00:17:3f:2e:88:0a brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
wlan0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
lo: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
eth0: 4586869 5220 0 0 0 0 0 0 619719 4174 0 0 0 0 0 0
*** Protocol statistics:
Ip:
5126 total packets received
0 forwarded
0 incoming packets discarded
5126 incoming packets delivered
4072 requests sent out
Icmp:
0 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
0 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
Tcp:
30 active connections openings
7 passive connection openings
0 failed connection attempts
0 connection resets received
1 connections established
4642 segments received
3743 segments send out
0 segments retransmited
0 bad segments received.
2 resets sent
Udp:
309 packets received
0 packets to unknown port received.
0 packet receive errors
329 packets sent
UdpLite:
TcpExt:
2 invalid SYN cookies received
4 TCP sockets finished time wait in fast timer
8 delayed acks sent
Quick ack mode was activated 23 times
85 packets directly queued to recvmsg prequeue.
84083 bytes directly received in process context from prequeue
2311 packet headers predicted
79 packets header predicted and directly queued to user
941 acknowledgments not containing data payload received
89 predicted acknowledgments
23 DSACKs sent for old packets
TCPRcvCoalesce: 637
TCPOFOQueue: 673
TCPAutoCorking: 244
TCPOrigDataSent: 1417
IpExt:
InMcastPkts: 108
InBcastPkts: 67
InOctets: 4509465
OutOctets: 558115
InMcastOctets: 3888
InBcastOctets: 6736
InNoECTPkts: 5126
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface [8086:2570] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:101b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [e4] Vendor Specific Information: Len=06 <?>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation 82865G Integrated Graphics Controller [8086:2572] (rev 02) (prog-if 00 [VGA controller])
Subsystem: Fujitsu Technology Solutions Fujitsu-Siemens Scenic E300 i865GV [1734:101b]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at d0000000 (32-bit, non-prefetchable) [size=512K]
Region 2: I/O ports at 1000 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: [d0] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: i915
00:06.0 System peripheral [0880]: Intel Corporation 82865G/PE/P Processor to I/O Memory Interface [8086:2576] (rev 02)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at 60000000 (32-bit, non-prefetchable) [size=4K]
00:1d.0 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 [8086:24d2] (rev 02) (prog-if 00 [UHCI])
Subsystem: Fujitsu Technology Solutions PRIMERGY RX/TX series onboard UHCI [1734:101c]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 1400 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 [8086:24d4] (rev 02) (prog-if 00 [UHCI])
Subsystem: Fujitsu Technology Solutions PRIMERGY RX/TX S2 series onboard UHCI [1734:101c]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 1800 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 [8086:24d7] (rev 02) (prog-if 00 [UHCI])
Subsystem: Fujitsu Technology Solutions PRIMERGY RX/TX S2 series onboard UHCI [1734:101c]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1c00 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4 [8086:24de] (rev 02) (prog-if 00 [UHCI])
Subsystem: Fujitsu Technology Solutions PRIMERGY RX/TX S2 series onboard UHCI [1734:101c]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 2000 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller [8086:24dd] (rev 02) (prog-if 20 [EHCI])
Subsystem: Fujitsu Technology Solutions Device [1734:101c]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at d0080000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci-pci
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev c2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
I/O behind bridge: 00004000-00004fff
Memory behind bridge: d0100000-d01fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1f.0 ISA bridge [0601]: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge [8086:24d0] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Kernel driver in use: lpc_ich
00:1f.2 IDE interface [0101]: Intel Corporation 82801EB (ICH5) SATA Controller [8086:24d1] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Fujitsu Technology Solutions Device [1734:101c]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374
Region 4: I/O ports at 3000 [size=16]
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller [8086:24d3] (rev 02)
Subsystem: Fujitsu Technology Solutions PRIMERGY RX/TX S2 series SMBus [1734:101c]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 2400 [size=32]
Kernel driver in use: i801_smbus
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller [8086:24d5] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1020]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 2c00 [size=256]
Region 1: I/O ports at 2800 [size=64]
Region 2: Memory at d0080800 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at d0080400 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: snd_intel8x0
03:05.0 Ethernet controller [0200]: Belkin F5D7000 v7000 Wireless G Desktop Card [Realtek RTL8185] [1799:700f] (rev 20)
Subsystem: Belkin F5D7000 v7000 Wireless G Desktop Card [Realtek RTL8185] [1799:700f]
Physical Slot: 1
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 4000 [size=256]
Region 1: Memory at d0101000 (32-bit, non-prefetchable) [size=512]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: rtl818x_pci
03:08.0 Ethernet controller [0200]: Intel Corporation 82801EB/ER (ICH5/ICH5R) integrated LAN Controller [8086:1051] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:101a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 66 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d0100000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 4400 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: e100
** USB devices:
not available
-- System Information:
Debian Release: 8.2
APT prefers stable
APT policy: (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 3.16.0-4-686-pae (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=C (charmap=ANSI_X3.4-1968) (ignored: LC_ALL set to C)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-3.16.0-4-686-pae depends on:
ii debconf [debconf-2.0] 1.5.56
ii initramfs-tools [linux-initramfs-tool] 0.120
ii kmod 18-3
ii linux-base 3.5
ii module-init-tools 18-3
Versions of packages linux-image-3.16.0-4-686-pae recommends:
ii firmware-linux-free 3.3
pn irqbalance <none>
pn libc6-i686 <none>
Versions of packages linux-image-3.16.0-4-686-pae suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.02~beta2-22+deb8u1
pn linux-doc-3.16 <none>
Versions of packages linux-image-3.16.0-4-686-pae is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
ii firmware-linux-nonfree 0.43
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information excluded
Reply to: