Re: HDD-Probleme seit Kernel 2.6.30
Hi Sven,
On Wednesday 05 August 2009 17:37:15 Sven Hartge wrote:
> Matthias Breier <debian@coolinblue.de> wrote:
> > [ 6915.900299] sd 2:0:0:0: [sda] Unhandled error code
> > [ 6915.900304] sd 2:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET
> > driverbyte=DRIVER_OK [ 6915.900313] end_request: I/O error, dev sda,
> > sector 211380689
>
> Hmm, Platte defekt?
Das dachte ich auch erst, insbesondere da dein Gedanke mit dem Timeout durch fehlerhafte
Sektoren durchaus plausibel klingt.
>
> # smartctl -t long /dev/sda
> [ warten ]
> # smartctl -a /dev/sda
Hier die Ausgabe:
-----8<----------8<----------8<----------8<----------8<----------8<----------8<----------8<-----
smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD3200BEVT-75ZCT1
Serial Number: WD-WXE508DY7849
Firmware Version: 11.01A11
User Capacity: 320.072.933.376 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Thu Aug 6 00:17:48 2009 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (10800) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 127) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED
RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 186 185 021 Pre-fail Always -
1666
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 636
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 096 096 000 Old_age Always -
2937
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 626
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 24
193 Load_Cycle_Count 0x0032 192 192 000 Old_age Always -
24207
194 Temperature_Celsius 0x0022 113 087 000 Old_age Always - 34
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
240 Head_Flying_Hours 0x0032 097 097 000 Old_age Always -
2870
241 Unknown_Attribute 0x0032 057 057 000 Old_age Always -
143455980348155
242 Unknown_Attribute 0x0032 200 200 000 Old_age Always -
7094148326
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Extended offline Completed without error 00% 2937 -
# 2 Short offline Completed without error 00% 2568 -
# 3 Short offline Interrupted (host reset) 10% 1759 -
# 4 Short offline Completed without error 00% 1758 -
# 5 Short offline Completed without error 00% 18 -
# 6 Short offline Interrupted (host reset) 80% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
-----8<----------8<----------8<----------8<----------8<----------8<----------8<----------8<-----
Soweit ich die Angaben verstehe, ist alles im grünen Bereich. Ich hatte schonmal eine
defekte Platte, da war insbesonders die Zahl der Reallokationen (Reallocated_Event_Count)
wesentlich höher. Insofern glaube ich eher an ein Treiberproblem.
Tschö
Matthias
Reply to: