--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-4.1.0-trunk-686-pae: Please enable CONFIG_MMC_TOSHIBA_PCI
- From: Ondrej Zary <linux@rainbow-software.org>
- Date: Sat, 11 Jul 2015 19:16:19 +0200
- Message-id: <20150711171619.2937.26322.reportbug@portege>
Package: src:linux
Version: 4.1.1-1~exp1
Severity: wishlist
Dear Maintainer,
please set CONFIG_MMC_TOSHIBA_PCI=m to enable toshsd driver for SD/MMC card
reader found in some Toshiba laptops (as seen in lspci output below).
-- Package-specific info:
** Version:
Linux version 4.1.0-trunk-686-pae (debian-kernel@lists.debian.org) (gcc version 4.9.3 (Debian 4.9.3-1) ) #1 SMP Debian 4.1.1-1~exp1 (2015-07-07)
** Command line:
BOOT_IMAGE=/boot/vmlinuz-4.1.0-trunk-686-pae root=UUID=7bfcf541-c486-4de6-a2f1-bb5f8cfe4fc0 ro
** Not tainted
** Kernel log:
[ 9.402768] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input3
[ 9.402892] ACPI: Lid Switch [LID]
[ 9.403124] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 9.403180] ACPI: Power Button [PWRF]
[ 9.506786] ACPI: AC Adapter [ADP1] (on-line)
[ 9.628384] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 9.838857] ACPI: Video Device [VGA] (multi-head: yes rom: yes post: no)
[ 9.839168] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 9.839914] acpi device:1a: registered as cooling_device2
[ 9.840351] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/device:19/LNXVIDEO:00/input/input5
[ 9.851908] ACPI: Battery Slot [BAT1] (battery present)
[ 9.852165] ACPI: Battery Slot [BAT2] (battery absent)
[ 10.371943] wmi: Mapper loaded
[ 10.823434] toshiba_acpi: Toshiba Laptop ACPI Extras version 0.21
[ 10.827519] toshiba_acpi: KBD function keys not supported
[ 10.832968] input: Toshiba input device as /devices/virtual/input/input6
[ 10.835879] toshiba_acpi: Illumination device not available
[ 10.839845] toshiba_acpi: Keyboard illumination not available
[ 10.844767] toshiba_acpi: Accelerometer not supported
[ 10.845542] toshiba_acpi: USB Sleep and Charge not supported
[ 10.847047] toshiba_acpi: USB Rapid Charge not supported
[ 10.848221] toshiba_acpi: Sleep and Music not supported
[ 10.850462] toshiba_acpi: USB 3 not supported
[ 10.932718] yenta_cardbus 0000:02:0b.0: enabling device (0000 -> 0003)
[ 10.932870] yenta_cardbus 0000:02:0b.0: CardBus bridge found [1179:0001]
[ 11.060853] yenta_cardbus 0000:02:0b.0: ISA IRQ mask 0x04b8, PCI irq 11
[ 11.060917] yenta_cardbus 0000:02:0b.0: Socket status: 30000007
[ 11.060978] yenta_cardbus 0000:02:0b.0: pcmcia: parent PCI bridge window: [io 0xc000-0xcfff]
[ 11.061041] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc000-0xcfff:
[ 11.062004] excluding 0xc000-0xc0ff 0xc400-0xc4ff 0xcf40-0xcf7f
[ 11.065220] yenta_cardbus 0000:02:0b.0: pcmcia: parent PCI bridge window: [mem 0xdfd00000-0xdfdfffff]
[ 11.065284] pcmcia_socket pcmcia_socket0: cs: memory probe 0xdfd00000-0xdfdfffff:
[ 11.065342] excluding 0xdfd00000-0xdfd0ffff 0xdfdf0000-0xdfdfffff
[ 11.065495] yenta_cardbus 0000:02:0b.0: pcmcia: parent PCI bridge window: [mem 0x20000000-0x23ffffff pref]
[ 11.065558] pcmcia_socket pcmcia_socket0: cs: memory probe 0x20000000-0x23ffffff:
[ 11.065640] excluding 0x20000000-0x23ffffff
[ 11.099791] cfg80211: Calling CRDA to update world regulatory domain
[ 11.151181] lib80211: common routines for IEEE802.11 drivers
[ 11.151232] lib80211_crypt: registered algorithm 'NULL'
[ 11.201035] libipw: 802.11 data/management/control stack, git-1.1.13
[ 11.201087] libipw: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 11.226357] snd_intel8x0 0000:00:1f.5: enabling device (0000 -> 0003)
[ 11.318216] ipw2100: Intel(R) PRO/Wireless 2100 Network Driver, git-1.2.2
[ 11.318273] ipw2100: Copyright(c) 2003-2006 Intel Corporation
[ 11.319204] ipw2100: Detected Intel PRO/Wireless 2100 Network Connection
[ 11.355931] intel_rng: FWH not detected
[ 11.846393] ipw2100 0000:02:0a.0: firmware: direct-loading firmware ipw2100-1.3.fw
[ 11.937672] input: PC Speaker as /devices/platform/pcspkr/input/input8
[ 12.003669] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af:
[ 12.004682] excluding 0x170-0x177 0x1e0-0x1e7 0x1f0-0x1f7 0x370-0x377
[ 12.005414] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff:
[ 12.005717] excluding 0x3f0-0x3f7 0x480-0x48f 0x4d0-0x4d7
[ 12.006135] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff:
[ 12.006591] clean.
[ 12.006681] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7:
[ 12.007179] clean.
[ 12.007277] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff:
[ 12.007335] excluding 0xc0000-0xcbfff 0xe0000-0xfffff
[ 12.007534] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff:
[ 12.007644] clean.
[ 12.007733] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff:
[ 12.007840] clean.
[ 12.007929] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff:
[ 12.008782] clean.
[ 12.160075] snd_intel8x0 0000:00:1f.5: intel8x0_measure_ac97_clock: measured 55155 usecs (2657 samples)
[ 12.160151] snd_intel8x0 0000:00:1f.5: clocking to 48000
[ 12.372483] iTCO_vendor_support: vendor-support=0
[ 12.384675] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 12.384815] iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0xd860)
[ 12.385406] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 12.838378] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input7
[ 13.158341] EXT4-fs (sda3): re-mounted. Opts: (null)
[ 14.248067] cfg80211: Calling CRDA to update world regulatory domain
[ 15.738024] EXT4-fs (sda3): re-mounted. Opts: errors=remount-ro
[ 16.474806] lp: driver loaded but no devices found
[ 16.491492] ppdev: user-space parallel port driver
[ 16.573725] loop: module loaded
[ 16.821455] fuse init (API version 7.23)
[ 17.400079] cfg80211: Calling CRDA to update world regulatory domain
[ 18.658031] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 18.660335] e100 0000:02:08.0 eth0: NIC Link is Up 10 Mbps Half Duplex
[ 18.660570] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
** Model information
not available
** Loaded modules:
fuse
mmc_block
mmc_core
loop
parport_pc
ppdev
lp
parport
joydev
iTCO_wdt
iTCO_vendor_support
pcspkr
lpc_ich
pcmcia
psmouse
evdev
mfd_core
ipw2100
serio_raw
snd_intel8x0
libipw
snd_intel8x0m
lib80211
snd_ac97_codec
cfg80211
snd_pcm
yenta_socket
snd_timer
pcmcia_rsrc
toshiba_acpi
snd
pcmcia_core
rng_core
sparse_keymap
rfkill
wmi
soundcore
ac97_bus
battery
video
shpchp
ac
button
acpi_cpufreq
processor
ext4
crc16
mbcache
jbd2
sg
sd_mod
ata_generic
ehci_pci
uhci_hcd
ehci_hcd
pata_isapnp
ata_piix
e100
mii
usbcore
usb_common
thermal
fan
thermal_sys
libata
scsi_mod
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82855PM Processor to I/O Controller [8086:3340] (rev 03)
Subsystem: Toshiba America Info Systems Device [1179:0001]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [e4] Vendor Specific Information: Len=04 <?>
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Kernel driver in use: agpgart-intel
00:01.0 PCI bridge [0604]: Intel Corporation 82855PM Processor to AGP Controller [8086:3341] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
Memory behind bridge: dff00000-f7ffffff
Prefetchable memory behind bridge: 24000000-240fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1d.0 USB controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 [8086:24c2] (rev 03) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems Device [1179:0001]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at efe0 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 [8086:24c4] (rev 03) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems Device [1179:0001]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at ef80 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller [8086:24cd] (rev 03) (prog-if 20 [EHCI])
Subsystem: Toshiba America Info Systems Device [1179:0001]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 11
Region 0: Memory at 24100000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=0080
Kernel driver in use: ehci-pci
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 83) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=04, sec-latency=64
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: dfd00000-dfdfffff
Prefetchable memory behind bridge: 20000000-23ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1f.0 ISA bridge [0601]: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge [8086:24cc] (rev 03)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Kernel driver in use: lpc_ich
00:1f.1 IDE interface [0101]: Intel Corporation 82801DBM (ICH4-M) IDE Controller [8086:24ca] (rev 03) (prog-if 8a [Master SecP PriP])
Subsystem: Toshiba America Info Systems Device [1179:0001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374
Region 4: I/O ports at bfa0 [size=16]
Region 5: Memory at 24100400 (32-bit, non-prefetchable) [size=1K]
Kernel driver in use: ata_piix
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller [8086:24c5] (rev 03)
Subsystem: Toshiba America Info Systems Device [1179:0205]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 0: I/O ports at 1000 [size=256]
Region 1: I/O ports at 1880 [size=64]
Region 2: Memory at 24100800 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at 24100a00 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: snd_intel8x0
00:1f.6 Modem [0703]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller [8086:24c6] (rev 03) (prog-if 00 [Generic])
Subsystem: Toshiba America Info Systems Device [1179:0001]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 0: I/O ports at 1400 [size=256]
Region 1: I/O ports at 1800 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: snd_intel8x0m
01:00.0 VGA compatible controller [0300]: Trident Microsystems CyberBlade XP4m32 [1023:2100] (rev 91) (prog-if 00 [VGA controller])
Subsystem: Toshiba America Info Systems Device [1179:0002]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 8
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f0000000 (32-bit, non-prefetchable) [size=128M]
Region 1: Memory at efc00000 (32-bit, non-prefetchable) [size=4M]
Region 2: Memory at e0000000 (32-bit, non-prefetchable) [size=128M]
Region 3: Memory at dfff8000 (32-bit, non-prefetchable) [size=32K]
[virtual] Expansion ROM at 24000000 [disabled] [size=256K]
Capabilities: [80] AGP version 2.0
Status: RQ=33 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [90] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
02:08.0 Ethernet controller [0200]: Intel Corporation 82801DB PRO/100 VE (MOB) Ethernet Controller [8086:103d] (rev 83)
Subsystem: Toshiba America Info Systems Device [1179:0001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at dfdff000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at cf40 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: e100
02:0a.0 Network controller [0280]: Intel Corporation PRO/Wireless LAN 2100 3B Mini PCI Adapter [8086:1043] (rev 04)
Subsystem: Intel Corporation Toshiba Satellite M10 [8086:2581]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 8500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at dfdfe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Kernel driver in use: ipw2100
02:0b.0 CardBus bridge [0607]: Toshiba America Info Systems ToPIC100 PCI to Cardbus Bridge with ZV Support [1179:0617] (rev 33)
Subsystem: Toshiba America Info Systems Device [1179:0001]
Physical Slot: 0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=03, sec-latency=0
Memory window 0: 20000000-23ffffff (prefetchable)
Memory window 1: 28000000-2bffffff
I/O window 0: 0000c000-0000c0ff
I/O window 1: 0000c400-0000c4ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Capabilities: [80] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Kernel driver in use: yenta_cardbus
02:0d.0 System peripheral [0880]: Toshiba America Info Systems SD TypA Controller [1179:0805] (rev 05)
Subsystem: Toshiba America Info Systems Device [1179:0001]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 255
Region 0: Memory at dfd00000 (32-bit, non-prefetchable) [disabled] [size=512]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
-- System Information:
Debian Release: 8.1
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable'), (1, 'experimental')
Architecture: i386 (i686)
Kernel: Linux 4.1.0-trunk-686-pae (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: sysvinit (via /sbin/init)
Versions of packages linux-image-4.1.0-trunk-686-pae depends on:
ii debconf [debconf-2.0] 1.5.56
ii initramfs-tools [linux-initramfs-tool] 0.120
ii kmod 18-3
ii linux-base 3.5
Versions of packages linux-image-4.1.0-trunk-686-pae recommends:
ii firmware-linux-free 3.3
pn irqbalance <none>
ii libc6-i686 2.19-18
Versions of packages linux-image-4.1.0-trunk-686-pae suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.02~beta2-22
pn linux-doc-4.1 <none>
Versions of packages linux-image-4.1.0-trunk-686-pae is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
ii firmware-ipw2x00 0.43
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information excluded
--- End Message ---